l Sink Basin Installation Sheet

ManualsBrandsAmerican Standard ManualsBathroom Remodel & Bathroom FixturesBoulevard Vitreous China Rectangular Pedestal Bathroom Sink with Overflow

SAVE FOR FUTURE USE

7301354-100

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

0641 BOULEVARD

0403 TROPIC PETITE

0404 TROPIC GRANDE

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product

is installed properly, please read these instructions carefully before you begin. (Certain installations may require

professional help.) Also be sure your installation conforms to local codes.

OBSERVE LOCAL PLUMBING AND BUILDING CODES

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Drill Tape Measure

Hacksaw Phillips Screwdriver Pipe Wrench Basin Wrench Channel Lock Pliers

Level Saber Saw Plumber’s Putty or Caulking

This lavatory can be installed 4 different ways. Please follow the instructions for your installation method.

1. PEDESTAL 3. ABOVE COUNTER 4. DROP-IN2. WALL-HUNG ON FURNITURE

1. Pedestal installation

1-C

1-A

1-B

1-D

Provide suitable reinforcement behind

finished wall for lavatory mounting screws.

Determine horizontal center line location

of support from fixture.

NOTE: If replacing an existing sink be

certain to shut off water supply before

removing old sink.

C/L of 2X6

Support

Finished

Floor

Mark lavatory and pedestal

screw locations through the

mounting holes.

Approx. Bumper

locations to raise

the lavatory slab

left side.

Top of Pedestal

Place lavatory and pedestal

into installed position. Level

and square the lavatory and

pedestal assembly. Use one

or more bumper cushions to

level and cushion lavatory slab

to pedestal.

For example only

Remove lavatory and pedestal from

installed position. Drill pilot holes for

lavatory and pedestal anchor screws

or lag bolts.

Note: Some models are supplied with

lag bolts, anchor screws, or steel

hangers for lavatory installations only.

Other models and all pedestals are

not provided with mounting hardware.

Various pedestal screw sizes and

types are available to the installer at

local hardware outlets.

not recommended for 0404

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE 0641 BOULEVARD 0403 TROPIC PETITE 0404 TROPIC GRANDE Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
1-E ANCHOR SCREW INSTALLATION Install lavatory anchor screws leaving 1-7/8" threaded end exposed as illustrated. LAG BOLT INSTALLATION Use lag bolts to secure lavatory as illustrated. Lavatory 1-7/8" Lavatory Steel Hanger Lag Bolt Anchor Screw Nut Washer Washer Lavatory IMPORTANT: Final assembly of nut and washer or lag bolt method shown for reference only. 1-G Return the fitted lavatory to the installed position. Connect trap to drain assembly hand tight to check alignment.
PAGE 3
2-F 2-G C B Shut-Off Valves Connect trap to drain assembly hand tight to check alignment. It may be necessary to cut off part of the tailpiece (area “B”) or part of the horizontal leg of the trap (area “C”). Secure joints for watertight assembly. Connect supply line to faucet (finger tight) and carefully bend tubes to engage with the supply shut-off valves. Tighten connections at faucet and shut-off valves for secure seal. 3. Above Counter OR 4.
PAGE 4
3-F 4-F Use the mounting holes on the rear of the lavatory to secure the sink to the wall. 3-G 4-G 3-H 4-H C B Shut-Off Valves Connect trap to drain assembly hand tight to check alignment. It may be necessary to cut off part of the tailpiece (area “B”) or part of the horizontal leg of the trap (area “C”). Secure joints for watertight assembly. Connect supply line to faucet (finger tight) and carefully bend tubes to engage with the supply shut-off valves.