Faucet Installation Instructions

ManualsBrandsAmerican Standard ManualsBathroom Remodel & Bathroom FixturesRetrospect Ceramic Specialty Console Bathroom Sink with Overflow

Plumbers' Putty or CaulkingAdjustable Wrench Phillips ScrewdriverChannel Locks

TOOLS REQUIRED

Installation

Instructions

M968301

Certified to comply with ANSI A112.18.1M

SPOUT ASSEMBLY

VALVE INSTALLATION

5/16'' MIN.

SPOUT

BASE

SPOUT

Insert VALVE BODY (1) through hole from underside

of SINK (2). Threads of VALVE BODY (1) should extend

at least 5/16 inch above SINK (2) top. If necessary,

adjust LOCKNUT (3). Make sure RUBBER WASHER (6)

is installed.

Place RUBBER RING (4) on LAVATORY (2) and thread

DECK ADAPTER (5) onto VALVE BODY (1) until snug

against internal stop.

TEE AND HOSE INSTALLATION

2373.801

2373.821

Connect COUPLING NUT (3) on TEE (1) to SPOUT SHANK (2).

Tighten COUPLING NUT (3).

Connect COUPLING NUTS (4) of HOSE to each valve outlet and

tighten securely.

HOSE

Install RING WASHER (1) into SPOUT

BASE. Insert SPOUT SHANK (2) through

SPOUT ESCUTCHEON (3) and into center

hole of lavatory or mounting surface.

Assemble RUBBER WASHER (4),

BRASS WASHER (5) and LOCKNUT (6)

onto threads of SPOUT SHANK (2)

from underside of mounting surface.

Insert LIFT ROD (7) through SPOUT

and cut out of BRASS WASHER (5).

Turn off hot and cold water supplies before beginning.

CAUTION

VALVE

OUTLET

WIDESPREAD LAVATORY FAUCET

with POP-UP DRAIN

ENFIELD

Tubing Cutter

Align SPOUT and tighten LOCKNUT (6).

Cut out in BRASS WASHER (5) and

RUBBER WASHER (4) should be

positioned as shown.

CUT OUT

LAVATORY OR

MOUNTING

SURFACE

Set VALVE BODIES (1) so that their outlets are facing

toward center of lavatory and then tighten LOCKNUT (3)

using WRENCH (7) supplied with faucet.

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years.

To ensure that your installation proceeds

smoothly--please read these instructions carefully before you begin.

Summary of content (4 pages)

PAGE 1
Installation Instructions ENFIELD WIDESPREAD LAVATORY FAUCET with POP-UP DRAIN 2373.801 2373.821 Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M968301 TOOLS REQUIRED Channel Locks Tubing Cutter 1 Adjustable Wrench 2 SPOUT ASSEMBLY CAUTION Turn off hot and cold water supplies before beginning.
PAGE 2
4 INSTALL POP-UP DRAIN Push Tail piece (11) down into Trap (C) (threaded end up). Thread Locknut (5), Washer (4) and Gasket (3) (Bevel side up) onto Drain Body (10). 1 Apply a bead of Putty (D) to underside of Flange (2). Feed Drain Body (10) up through Sink (A) and thread the Flange (2) fully onto Drain Body (10). Tighten Locknut (5) firmly, keeping the pivot rod hole pointed towards the back of the sink. 2 D A E Assemble Pivot Rod (9) as shown in Figure-4A.
PAGE 3
6 INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. See figure "A". Tighten STEM SCREW (3) to secure ADAPTER (1). 4 Find correct position of LEVER HANDLE ASSEMBLY (4) or CROSS HANDE ASSEMBLY (5) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4, 5). THREAD ON TO DECK ADAPTER 5 Thread LEVER HANDLE ASSEMBLY (4) or CROSS HANDE ASSEMBLY (5) onto DECK ADAPTER (6) until snug against mounting surface.
PAGE 4
ENFIELD WIDESPREAD LAVATORY FAUCET MODEL NUMBER M962246-YYY0A LIFT ROD 2373.801 2373.