Instructions / Assembly

ManualsBrandsAmerican Standard ManualsAlcove Shower DoorsPassage 60 in. x 72 in. Frameless Sliding Shower Door in Clear Glass

710443-100 Rev. 2 8/20

Product names listed herein are trademarks of AS America Inc.

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. Certain installations may require professional

help. Also be sure your installation conforms to local codes.

INSTALLATION INSTRUCTIONS

PASSAGE

™

60" x 72" FRAMELESS SHOWER DOOR

MODEL: AM801703400 SERIES

REQUIRED TOOLS AND MATERIALS

INSTALLATION PREPARATION

• Please unpack carefully and identify all parts needed for installation by using the Box Contents page as a

reference. Inspect the product and report any damages or missing parts immediately to customer care by

calling 800-442-1902. Follow the prompts for consumer/shower doors.

• These Passage shower doors were developed to be installed with the Passage shower base and Passage

shower walls. If you are using a different base and walls, you may need additional hardware and tools to

complete the installation.

• The Passage shower door dimensions are nominal and meant for a standard 60" (1524mm) alcove. Alcove

sizes may vary based on stud and wall material thickness. Please double check your measurements prior to

starting your install.

• Handle the glass panels carefully and protect the edges. Unequal pressure applied during installation can

cause cracking or breakage, and the sharp corners on the glass panels can cause damage to the wall or

floor materials.

• Ensure adequate wall support is provided to area where shower door is to be installed.

• Shower base and wall material must be installed prior to the door installation.

• Wear protective equipment during installation to avoid injury.

• Please keep these instructions for after care and customer service details.

SAVE FOR FUTURE USE

Regular Screwdriver

Safety Glasses

Phillips Screwdriver

10'

Caulking Gun & Silicone

Drill 1/4" (6mm) & 1/8" (3.2mm)

Drill Bits #2 Square Drive Bit

Level

Tape Measure

Hammer

Pencil

Painter’s

Masking Tape

Utility Knife

3/8" (10mm) Socket Wrench

3/4" (18mm) Open End Wrench

Visit http://www.americanstandard-us.com/passage-collection for coordinating products.

Visit https://youtu.be/GXpYwYBU_2c for step by step video instructions.

WARNING: Product is heavy and REQUIRES TWO PEOPLE for installation.

WARNING: TEMPERED GLASS CANNOT BE DRILLED, CUT OR MODIFIED.

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS PASSAGE™ 60" x 72" FRAMELESS SHOWER DOOR MODEL: AM801703400 SERIES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. Certain installations may require professional help. Also be sure your installation conforms to local codes. Visit http://www.americanstandard-us.com/passage-collection for coordinating products.
PAGE 2
BOX CONTENTS [1] 1x Horizontal Rail INSTALLATION INSTRUCTIONS 1 Installation Instructions PASSAGE™ 60x72 FRAMELESS SHOWER DOOR MODEL: AM801703400 SERIES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
PAGE 3
ASSEMBLY DRAWING [12] [15] [33] [9] [11a] [8] [10] [1] [11b] [13] [14] [16] [22] [24] [20] [21] [19] [31] [23] [32] [2] [25] [17] [27] [28] [5] [26] [3] [7] [6] [29] [4] [30] [1] 1x Horizontal Rail [2] 1x Door Handle [3] 1x Screws M4x35 [4] 1x Wall Anchor [5] 1x Screw Cover Cap [6] 1x Bottom Guide [7] 1x Shim [8] 2x Rollers [9] 2x Fixed Panel Fasteners [10] 2x Door Panel Guards [11] 2x Wall Connectors [12] 2x Connector Base Mounts [13] 2x Cushions [14] 4x Wall Anchors [15] 4x Screws
PAGE 4
1 In Step 1, we will cover attaching the connector base mounts and the wall posts for the stationary glass door panel. This will require parts 11, 12, 13, 14, 15, 21, 22, 23 and 24. NOTE: The Passage Shower Door can be installed with the fixed door panel on the left or right hand side. The illustrations below show the door assembled with the handle on the right side of the shower.
PAGE 5
2 In Step 2, we will cover installing the floor U Channel and Bottom Guide. This will require parts 3, 4, 5, 6, 7, 21, 23, 28, 31 and 32. 2a. Place U Channel [28] and Bottom Guide [6] on the Fixed Wall Post [21] side on the edge of the shower base threshold. NOTE: The smaller side of the Bottom Guide is meant to hold the Fixed Panel [31] (with the rubber Shim [7]), while the larger side is meant to hold the sliding Door Panel [32] (without rubber Shim [7] ).
PAGE 6
3 ! In Step 3, we will cover the assembly and installation of the fixed door panel. This will require parts 6, 7, 17, 21, 22, 23, 24, 27, 28 and 31. NOTE: Product is heavy and REQUIRES TWO PEOPLE for installation. 3a. Ensure clear Shim [7] is in groove on Bottom Guide [6] for Fixed Panel side. NOTE: Place a minimum of 2 clear channel shims in bottom of U channel. Clear channel shims Clear channel shims 3a [7] 3b 3b.
PAGE 7
5 In Step 5, we will cover the installation of the horizontal rails and wall connectors. This will require parts 1, 9, 11a, 12, 31 and 33. [11a] 5a. Screw Limit Block [33] to Wall Connector [11a]. 5a [33] NOTE: Wall Connector [11a] has a threaded hole on one side to accommodate the Limit Block. [11a] 5b. Attach Wall Connector with Limit Block to Connector Base Mount [12] on the Fixed Panel [31] side of shower and tighten 2 allen screws using supplied hex allen key. 5b 5c.
PAGE 8
6 In Step 6, we will cover assembling the rollers and sliding glass panel door. This will require parts 2, 8, 18 and 32. 6a. Separate door handles [2] by removing brass connector with threaded stem from handles. Place the round bushing and clear square gasket over the threaded stem and onto the Sliding Door Panel [32] keeping clear washers between the glass panel. Then place the other handle over brass connector. 6a [2] 6b 6b. Tighten allen screws to secure Door Handle in place. 6c.
PAGE 9
7 ! In Step 7, we will cover attaching the sliding glass door panel to the horizontal rail. This will require parts 1, 6, 8, 10, 16, 19, 20, 21 and 32. NOTE: Product is heavy and REQUIRES TWO PEOPLE for installation. [8] 7a. Carefully place Sliding Door Panel [32] onto Horizontal Rail [1] from inside of shower area and onto the Rollers [8]. 7a [6] 7b. Ensure bottom of Sliding Door Panel [32] onto Horizontal Rail [1] from inside of shower area and onto the Rollers [8]. 7c.
PAGE 10
8 In Step 8, we will cover adjusting the Sliding Door Panel [32]. 8a. Once all assembly is completed, it may be necessary to adjust the Sliding Door Panel [32] for proper operation. This can be achieved by adjusting Rollers [8] attached to the Sliding Door Panel [32] by loosening the metal nut on the Roller. 8a [8] [8] MAX MIN 8b.
PAGE 11
10 In Step 10, we will cover attaching the hardware to the Sliding Wall Post. This will require parts 20, 21 and 26. 10a. Three hole locations are predrilled into the Post [20] and can be used to mark drill locations in the Sliding Wall Post [21] from the inside of shower. Remove Post and drill marked locations using a 1/8" (3.2mm) drill bit. 10b. Place Post [20] back onto Sliding Wall Post [21} and use 3 supplied M4x8 screws, placing white plastic cups through each screw to hold Screw Cover Caps [26].
PAGE 12
MAINTENANCE: Two primary materials are used to manufacture your new American Standard shower enclosure: tempered glass and anodized aluminum. To assure a long lasting finish on the enclosure, wipe it down with a towel after each use. For occasional, more concentrated cleaning efforts Lysol Non-Abrasive Bathroom Cleaner works extremely well. Be sure that any over spray falling on the aluminum frame is rinsed thoroughly and dried.