THE BEST BATH OR SHOWER EXPERIENCE? THE ONE NOBODY INTERRUPTS. Thank you for buying an American Standard bath or shower product. We’re so grateful you did, and you will be too. Not just while you’re waking up each morning, but also every time a dirty gardener, sweaty soccer player, or muddy dog gets cleaned up. How do we know? Just like you, we’ve lived with that same beautiful chaos called life for almost 150 years.
OWNERS MANUAL Ovation Curve™ Neo-Angle Shower Door AM00847400 INSTALLATION INSTRUCTIONS Thank you for selecting American Standard – the benchmark of fine quality for over 150 years. To ensure this product is installed properly, please read these instructions carefully before you begin. Certain installations may require professional help. Also be sure your installation conforms to local codes.
INSIDE THE BOX Left Hand Opening Right Hand Opening Image shown may vary from product purchased. RECOMMENDED TOOLS AND MATERIALS Installation steps will indicate which tools should be used with asscociated letter Drill 1/4"&(61/8" mm)) 1/4" (6mm) (3.2mm) Drill Bits Drive Drill Bits#2 #2 Square Square Drive BitBit Caulking Gun Level Drill A B C D Phillips Screwdriver Utility Knife Regular Drill Screwdriver 1/8" (3.2 mm) 1/4" (6mm) & 1/8" (3.
BOX CONTENTS 1x Installation Instruction [1] 2x Wall Posts [2] 2x Side Covers [3] 1x Support Bar [4] 1x Bottom Threshold [5] 1x Bottom Gasket [6] 1x Side Gasket [7] 1x Magnetic Seal [8] 1x Magnetic Seal [9] 1x Door Panel [10] 1x Fixed Panel A [11] 1x Fixed Panel B [12] 1x Handle Set [13] 2x Hinges [14] 6x Screws M4x16 [15] 6x Adjust Fixtures [16] 2x Screws ST4x35 [17] 2x Wall Brackets [18] 6x Caps [19] 1x Fixing (L) [20] 1x Fixing (R) [21] 2x Screws ST4x25 [22] 10x Wall Anchors [23] 8x Screws ST4x35 [24] 1
ASSEMBLY DRAWING [17] [16] [18] [01] [03] [10] [06] [22] [23] [08] [07] [15] [14] [09] [13] [12] [02] [11] [25] [05] [21] [19] [1] 2x Wall Posts [2] 2x Side Covers [3] 1x Support Bar [4] 1x Bottom Threshold [5] 1x Bottom Gasket [6] 1x Side Gasket [7] 1x Magnetic Seal [8] 1x Magnetic Seal [9] 1x Door Panel [04] [10] 1x Fixed Panel A [11] 1x Fixed Panel B [12] 1x Handle Set [13] 2x Hinges [14] 6x Screws M4x16 [15] 6x Adjust Fixtures [16] 2x Screws ST4x35 [17] 2x Wall Brackets [18] 6x Caps [24
DETERMINING DOOR OPENING SIDE NOTE: Before installing the shower door, determine the door opening side. If it is to be a Left Hand Opening (as illustrated), proceed to step 1. If it is to be a Right Hand Opening (as illustrated), disassemble both hinges as per the images below and reassemble to prepare the hinges for Right Hand Opening.
INSTALLATION INSTRUCTIONS IMPORTANT GENERAL INFORMATION This unit is best installed by two people. Cover drain with tape prior to installation to prevent the loss of small parts. Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using Box Contents and Assembly Drawing as a reference. Before discarding the carton check to see that no small hardware parts have fallen to the bottom of the box.
1 INSTALLING WALL POSTS • In this step, you’ll need following parts: [1] x2, [22] x8, [23] x8, [26] x1 • In this step, you’ll need the following tools: B, C, D, G, I, J 1e 1a L [26] J [26] [26] R View from Outside [1] [1] L 1b B 1a 1a 1f C D B Shower Wall [26] L J 6mm [1] [1] [1] 1c [22] 1g I Shower Wall C ≈ 3/4"-1" 19-25 mm Shower Wall 6mm D 1d View from Outside 1h [22] G [1] [23] Round Head Screw ST4x35 I Shower Wall 1a.
2 INSTALLING FIXED PANEL A & B • In this step, you’ll need following part: [10] x1, [11] x1, [15] x6, [14] x6 • In this step, you’ll need the following tool: G [10] View from Inside View from Outside View of Countersunk Hole 2a B View from Inside 2c [15] [1] [1] [10] [14] Screw M4x16 2d 2b [15] [1] [10] [1] [10] G [15] View from Inside [10] [11] 2a. Insert Fixed Panel A [10] into narrow slot of Wall Post [1]. 2b.
3 INSTALLING DOOR PANEL AND HINGES • In this step, you’ll need following parts:[4] x1, [6] x1, [9] x1, [13] x2, [19] x2 [10] [11] [9] 3c 3a 3b [19] [10] [10] [6] [4] 3b 3e 3c [9] [13] View from Outside [10] [13] [10] [25] 3a View from Inside 3f 3d [10] [13] 3e [10] [9] [10] [13] [9] [10] [9] [9] View from Inside Correct Alignment Incorrect Alignment 3a. Slide notch of Fixing L [19] into bottom of Fixed Panel A [10].
4 INSTALLING BOTTOM GASKET AND MAGNETIC SEALS • In this step, you’ll need following parts: [5] x1, [7] x1, [8] x1 • In this step, you’ll need the following tools: A, H 4a 4b [9] [7] [11] View from Outside [9] [5] [8] [7] 4c 4b 4d [9] [9] [5] 4e Shower Base [5] A [7] 4f [7] [7] 4a [9] [9] H 4a. Open Door Panel [9] and install Bottom Gasket [5] on bottom of door panel. Note the direction of the gasket in illustration 4a. 4b.
5 ADJUSTING DOOR PANEL • In this step, you’ll need following part: [27] • In this step, you’ll need the following tool: H 5a [8] [8] [7] 5a [7] [11] [9] Incorrect Fit 5e [10] 5b [27] [11] [9] Correct Fit 5d [11] [9] [9] Shower Base Threshold [7] 5c [10] 5b [8] H [9] Shower Base Threshold 5e Correct Fit Incorrect Fit Incorrect Fit 5a.
6 MOUNTING BOTTOM THRESHOLD TO DECK OF BASE • In this step, you’ll need following parts: [18], [21] • In this step, you’ll need the following tools: C, F [20] 6a = [19] [4] = Base Threshold C 6b [18] 6c [21] Screw ST4x25 [4] [19] 3.2mm F [19] View from Inside 6a. Verify that the Bottom Threshold [4] is positioned evenly in front of deck of shower base. 6b. Drill a 3.2mm hole through the Fixing L [19] into the deck of the shower base. 6c.
7 INSTALLATION OF SUPPORT BAR • In this step, you’ll need following parts: [3], [16], [17], [18] • In this step, you’ll need the following tool: G 7a 7b G Bracket Mount [17] [3] [16] Bracket Mount Screw ST4x35 [24] [3] 7c 7d [17] [25] [18] [3] View from Inside 7e [6] [9] 7f [6] [10] [10] [9] Incorrect Fit [6] [10] [9] Correct Fit 7a.
8 INSTALLING HANDLE SET AND SIDE COVERS • In this step, you’ll need following parts: [2], [12] View from Inside 8a 8c [24] 8c [9] [10] [1] [12] [2] 8a 8b 8d [9] [10] [1] [12] [2] View from Inside 8a. Remove short end of threaded nut and washers from Handle Set [12]. This end of the Handle Set should be installed nearest the door hinges. Ensure the clear washers are installed inside and outside of Door Panel [9] as illustrated. Lightly snug threaded nut. 8b.
9 APPLYING SEALANT ON HINGE COVER PLATE • In this step, you’ll need the following tool: A 9a Hinge Cover A 9b [13] Hinge Cover View from In side 9a. Apply Sealant [A] around the Hinge Cover [13] as illustrated. 9b. Line up the 4 studs of the Hinge Cover [13] over the Hinge [13] and snap into place. 10 APPLY SEALANT TO SHOWER DOOR • In this step, you’ll need the following tool: A A View from In side Allow 24 hours for silicone to dry before use 10a.
POST INSTALLATION CLEAN-UP Remove all construction debris from bath. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter’s naphtha can be used to remove excess adhesives and/or wet oil-base paint.
WARRANTY SHOWER DOORS 10 YEAR WARRANTY AS America, Inc. (“American Standard®”) warrants to the original non-commercial owner that it will, at its sole option, repair or replace this product or any part of this product, if it confirms that the product is defective in materials or workmanship under normal use and maintenance for 10 years. This warranty is non-transferable to subsequent purchasers or owners.
TELL US WHAT YOU THINK! Please leave us a product review or story at americanstandard.com/reviews Great Tub 03/13/2018 06:52:29 CDT American Standard Bathtubs Saver 60 Inch by 34 Inch Integral Apron Bathtub. Left Hand Drain Love the tub. It is very roomy and would definitely buy it again. Our old tub cracked so we got this one to replace it. This one feels like it is more durable and not as flimsy as the last one. Register your warranty and sign up for an idea-filled newsletter at americanstandard.
LA MEILLEURE EXPÉRIENCE DE BAIN OU DE DOUCHE? CELLE QUE PERSONNE N’INTERROMPT. Merci d’avoir acheté une baignoire ou une douche American Standard. Nous sommes si contents que vous l’ayez fait, vous le serez également. Pas seulement au réveil le matin, mais aussi chaque fois qu’un jardinier sale, qu’un joueur de soccer en sueur ou qu’un chien couvert de boue doit se nettoyer. Comment le savons-nous? Tout comme vous, nous vivons dans ce même désordre qu’est la vie depuis presque 150 ans.
MANUEL DU PROPRIÉTAIRE Porte de douche Néo-angle Ovation Curve AM00847400 MC CONSIGNES D’INSTALLATION Merci d’avoir choisi American Standard, la référence en matière de qualité supérieure depuis plus de 150 ans. Pour vous assurer de l’installation adéquate de ce produit, veuillez lire ces consignes avant de commencer. Certaines installations peuvent nécessiter l’aide d’un professionnel. Assurez-vous que votre installation respecte les codes locaux.
CONTENU DE LA BOÎTE Ouverture à gauche Ouverture à droite L’illustration peut être différente du produit acheté. OUTILS ET MATÉRIEL RECOMMANDÉS Les outils à utiliser seront indiqués par la lettre correspondante à chacune des étapes de l’installation. Pistolet de calfeutrage A Tournevis à Drill tête plate Drill Forets 1/4 po (6 mm) 1/4" (6mm) & 1/8" (3.
CONTENU DE LA BOÎTE 1x consignes d’installation [1] 2x Poteaux muraux [2] 2x Revêtements latéraux [3] 1x Barre d’appui [4] 1x Seuil [5] 1x Joint du bas [6] 1x Joint latéral [7] 1x Scellant magnétique [8] 1x Scellant magnétique [9] 1x Panneau de porte [10] 1x Panneau fixe A [11] 1x Panneau fixe B [12] 1x Poignée [13] 2x Charnières [14] 6x Vis M4x16 [15] 6x Fixations de réglage [16] 2x Vis ST4x35 [17] 2x Chevilles murales [18] 6x Capuchons [19] 1x Pièce de fixation (gauche) [20] 1x Pièce de fixation (droite)
DESSIN DE MONTAGE [17] [16] [18] [01] [03] [10] [06] [22] [23] [08] [07] [15] [14] [09] [13] [12] [02] [11] [25] [05] [21] [19] [1] 2x Poteaux muraux [2] 2x Revêtements latéraux [3] 1x Barre d’appui [4] 1x Seuil [5] 1x Joint du bas [6] 1x Joint latéral [7] 1x Scellant magnétique [8] 1x Scellant magnétique [9] 1x Panneau de porte [24] [04] [10] 1x Panneau fixe A [11] 1x Panneau fixe B [12] 1x Poignée [13] 2x Charnières [14] 6x Vis M4x16 [15] 6x Fixations de réglage [16] 2x Vis ST4x35 [17] 2x
CHOIX DU SENS D’OUVERTURE DE LA PORTE REMARQUE : A vant de commencer l’installation, déterminez de quel côté il vaut mieux que la porte s’ouvre. Si elle s’ouvre à gauche (voir l’illustration), commencez à l’étape 1. Si elle s’ouvre à droite (voir illustration), démontez et réinstallez les deux charnières comme indiqué sur les images ci-dessous.
CONSIGNES D’INSTALLATION RENSEIGNEMENTS GÉNÉRAUX IMPORTANTS l est plus facile d’installer cette unité à deux personnes. Couvrez le drain avec du ruban avant l’installation pour éviter de perdre des petites pièces. Déballez votre produit avec soin et vérifiez qu’il n’est pas endommagé par le transport. Étalez et identifiez toutes les pièces au moyen de la page Contenu de la boîte et du dessin de montage. Avant de jeter la boîte, assurez-vous qu’aucune pièce n’y est tombée.
1 INSTALLATION DES POTEAUX MURAUX • Pièces requises pour cette étape : [1] x2, [22] x8, [23] x8, [26] x1 • Outils requis pour cette étape : B, C, D, G, I, J 1e 1a L [26] J [26] [26] R Vue de l'extérieur [1] [1] L 1b B 1a 1a 1f C D B Mur de douche [26] L J 6mm [1] [1] [1] 1c [22] 1g I Mur de douche C ≈ 3/4 -1 po Mur de 19-25 mm douche 6mm D 1d Vue de l'extérieur 1h G [1] [23] Vis à tête ronde ST4x35 [22] I Mur de douche 1a.
2 INSTALLATION DES PANNEAUX FIXES A ET B • Pièces requises pour cette étape : [10] x1, [11] x1, [15] x6, [14] x6 • Outil requis pour cette étape : G [10] Vue de l'intérieur Vue de l'extérieur Vue du trou fraisé 2a B Vue de l'intérieur 2c [15] [1] [1] [10] [14] Vis 2d 2b [15] [1] [10] [1] [10] G [15] Vue de l'intérieur [10] [11] 2a. Insérez le panneau fixe A [10] dans la fente étroite du poteau mural [1]. 2b.
3 INSTALLATION DU PANNEAU DE PORTE ET DES CHARNIÈRES • Pièces requises pour cette étape :4] x1, [6] x1, [9] x1, [13] x2, [19] x2 [10] [11] [9] 3c 3a 3b [19] [10] [10] [6] [4] 3b 3e 3c [9] [13] Vue de l'extérieur [10] [13] [10] [25] 3a Vue de l'intérieur 3f 3d [10] [13] 3e [10] [9] [10] [13] [9] [10] [9] [9] Vue de l'intérieur l’ajustement correct l’ajustement incorrect 3a. SFaites glisser l’encoche de la pièce de fixation gauche [19] dans le bas du panneau fixe A [10].
4 INSTALLATION DU JOINT DU BAS ET DES SCELLANTS MAGNÉTIQUES • Pièces requises pour cette étape : [5] x1, [7] x1, [8] x1 • Outils requis pour cette étape : A, H 4a 4b [9] [7] [11] Vue de l'extérieur [9] [5] [8] [7] 4c 4b 4d [9] [9] [5] 4e Base de douche [5] A [7] 4f [7] [7] 4a [9] [9] H 4a. Ouvrez le panneau de porte [9] et installez le joint du bas [5] sur le bas du panneau de porte. Remarquez bien le sens du joint dans l’illustration 4a. 4b.
5 RÉGLAGE DU PANNEAU DE PORTE-L • Pièce requises pour cette étape :[27] • Outil requis pour cette étape : H 5a [8] [8] [7] 5a [7] [11] [9] l’ajustement incorrect 5e [10] 5b [27] [11] [9] l’ajustement correct 5d [11] [9] [9] Seuil de la base de douche [7] 5c [10] 5b [8] H [9] Seuil de la base de douche 5e Ajustement correct Ajustement incorrect 5a.
6 INSTALLATION DU SEUIL SUR LA PLATEFORME DE LA BASE • Pièces requises pour cette étape : [18], [21] • Outils requis pour cette étape : C, F [20] Seuil de la base 6a = [19] = [4] C 6b [18] 6c [21] Vis ST4x25 [4] [19] 3.2mm F [19] Vue de l'intérieur 6a. Vérifiez que le seuil [4] est positionné de manière égale devant la plateforme de la base de douche. 6b. Percez un trou de 3,2 mm à travers la pièce de fixation gauche [19] dans la plateforme de la base de douche. 6c.
7 INSTALLATION DE LA BARRE D’APPUI • Pièces requises pour cette étape : [3], [16], [17], [18] • Outil requis pour cette étape : G 7a 7b G Support de montage [17] [3] [16] Vis ST4x35 Support de montage [24] [3] 7c 7d [17] [25] [18] [3] Vue de l'intérieur 7e [6] [9] 7f [6] [10] [9] [10] l’ajustement incorrect [6] [9] [10] l’ajustement correct 7a.
8 INSTALLATION DE LA POIGNÉE ET DES REVÊTEMENTS LATÉRAUX • Pièces requises pour cette étape : [2], [12] Vue de l'intérieur 8a 8c [24] 8c [9] [10] [1] [12] [2] 8a 8b 8d [9] [10] [1] [12] [2] Vue de l'intérieur 8a. Retirez l’écrou fileté et les rondelles de l’extrémité courte de la poignée [12]. Cette extrémité de la poignée doit être installée le plus près des charnières de la porte.
9 APPLICATION DE SCELLANT SUR LA PLAQUE DE PROTECTION DE LA CHARNIÈRE • Outil requis pour cette étape :A 9a Couvercle de charnière A 9b [13] Couvercle de charnière Vue de l'intérieur 9a. Appliquer du scellant [A] autour de la plaque de la charnière [13] comme illustré. 9b. Alignez les 4 goujons de la plaque de la charnière [13] sur la charnière [13] et mettez-les en place.
NETTOYAGE APRÈS L’INSTALLATION AS America, Inc. (« American Standard ») garantit à l’acheteur original qu’il retirera tous débris de construction de la douche, à sa demande. L’enduit de carrelage peut être retiré avec un bâtonnet de bois ou un abaisse-langue. N’utilisez pas de brosses métalliques ni tout autre instrument métallique sur la surface de la douche. En général, de l’eau tiède et du détergent liquide pour la vaisselle conviennent pour nettoyer après l’installation.
GARANTIE GARANTIE DE 10 ANS SUR LES PORTES DE DOUCHE AS America, Inc. (« American Standard® ») garantit au propriétaire original non commercial qu’il réparera ou remplacera, à son entière discrétion, ce produit ou toute pièce de ce produit qui révèle un défaut de fabrication ou de main-d’œuvre dans des conditions normales d’utilisation et d’entretien durant une période de 10 ans. La présente garantie ne peut être transférée à un achat ou un propriétaire subséquent.
FAITES-NOUS PART DE VOS COMMENTAIRES! S’il vous plaît laissez-nous une critique de produit ou une histoire à americanstandard.com/reviews Baignoire géniale 03/13/2018 06:52:29 HAC American Standard Économiseur de baignoire 60 pouces par 34 pouces intégral Baignoire à tablier. Renvoi à gauche J’adore la baignoire. Il est très spacieux et l’achèterait certainement à nouveau. Notre vieille baignoire s’est fissurée, alors nous avons eu celle-ci pour la remplacer.
¿LA MEJOR EXPERIENCIA DE TINA O DUCHA? LA QUE NADIE INTERRUMPE. Gracias por comprar una tina o ducha American Standard. Estamos muy agradecidos y usted también lo estará. No solo cuando se esté despertando cada mañana, sino también cada vez que se lave un jardinero sucio, un jugador de fútbol sudado o un perro embarrado. ¿Cómo lo sabemos? Tal como usted, hemos vivido con el mismo caos hermoso de la vida por casi 150 años.
MANUAL DEL PROPIETARIO Puertas de ducha Neo-Ángulo Ovation Curve™ AM00847400 INSTRUCCIONES DE INSTALACIÓN Gracias por elegir American Standard, el parámetro de excelente calidad por más de 150 años. Para asegurar la instalación adecuada de este producto, por favor lea las instrucciones con atención antes de comenzar. Algunas instalaciones pueden requerir ayuda profesional. Asimismo, asegúrese de realizar la instalación de conformidad con los códigos locales.
DENTRO DE LA Apertura a la izquierda Apertura a la derecha La imagen puede variar del producto comprado. RECOMMENDED TOOLS AND MATERIALS Installation steps will indicate which tools should be used with asscociated letter Pistola de calafateo Nivel Taladro A B C Destornillador Drill común Broca de 1/8" (3.2 mm) 1/4" (6mm) & 1/8" (3.2mm) cuadrada DrillBroca Bits #2 Square Drive#2 Bit Drill DestornilladorPhillips Broca de &1/4" mm)) 1/4" (6mm) 1/8" (6 (3.
CONTENIDO DE LA CAJA 1x Instrucciones de instalación [1] 2x postes de pared [2] 2x tapas laterales [3] 1x barra de soporte [4] 1x umbral inferior [5] 1x junta inferior [6] 1x junta lateral [7] 1x empaque magnético [8] 1x empaque magnético [9] 1x panel de puerta [10] 1x panel fijo A [11] 1x panel fijo B [12] 1x juego de manijas [13] 2x bisagras [14] 6x tornillos M4x16 [15] 6x accesorios de ajuste [16] 2x tornillos ST4x35 [17] 2x soportes de pared [18] 6x tapas [19] 1x fijación (L - izquierda) [20] 1x fijaci
DIAGRAMA DE ENSAMBLAJE [17] [16] [18] [01] [03] [10] [06] [22] [23] [08] [07] [15] [14] [09] [13] [12] [02] [11] [25] [05] [21] [19] [1] 2x postes de pared [2] 2x tapas laterales [3] 1x barra de soporte [4] 1x umbral inferior [5] 1x junta inferior [6] 1x junta lateral [7] 1x empaque magnético [8] 1x empaque magnético [9] 1x panel de puerta [04] [10] 1x panel fijo A [11] 1x panel fijo B [12] 1x juego de manijas [13] 2x bisagras [14] 6x tornillos M4x16 [15] 6x accesorios de ajuste [16] 2x torn
DETERMINAR EL LADO DE APERTURA DE LA PUERTA NOTA: Antes de instalar la puerta de la ducha, determine el lado de apertura de la puerta. Si va a ser una apertura a la izquierda (como se ilustra), proceda al paso 1. Si va a ser una apertura a la derecha (como se ilustra), desmonte ambas bisagras según las imágenes de abajo y vuelva a montarlas para preparar las bisagras para la apertura a la derecha.
INSTRUCCIONES DE INSTALACIÓN INFORMACIÓN GENERAL IMPORTANTE Se recomienda que dos personas instalen la unidad. Cubra el desagüe con cinta antes de realizar la instalación para no perder las piezas pequeñas. Desempaque la unidad con cuidado y fíjese que no haya sido dañada durante el envío. Despliegue las piezas e identifíquelas usando el diagrama de ensamblaje y la lista de contenido de la caja como referencia. Antes de desechar la caja, asegúrese de que no haya piezas pequeñas de ferretería en el fondo.
1 INSTALACIÓN DE LOS POSTES DE PARED • En este paso, necesitará las siguientes piezas:[1] x2, [22] x8, [23] x8, [26] x1 • En este paso, necesitará las siguientes herramientas: B, C, D, G, I, J 1e 1a L J [26] [26] R Vista desde el exterior [1] [1] L 1b B 1a 1a 1f C Pared de ducha [26] L D B [26] J 6mm [1] [1] [1] 1c [22] ≈ 3/4"-1" 19-25 mm Pared de ducha 1g I Pared de ducha C 6mm D 1d Vista desde el exterior 1h [22] I G [1] Pared de ducha Tornillo de cabeza redonda ST4
2 INSTALACIÓN DE LOS PANELES FIJOS A Y B • En este paso, necesitará las siguientes piezas: [10] x1, [11] x1, [15] x6, [14] x6 • En este paso, necesitará las siguientes herramienta: G [10] Vista desde el interior Vista desde el exterior Vista del agujero avellanado B 2a Vista desde el interior 2c [15] [1] [1] [10] [14] Tornillo M4x16 2d 2b [15] [1] [10] [1] [10] G [15] Vista desde el interior [10] [11] 2a. Inserte el panel fijo A [10] en la ranura angosta del poste de pared [1]. 2b.
3 INSTALACIÓN DEL PANEL DE LA PUERTA Y LAS BISAGRAS • En este paso, necesitará las siguientes piezas: [4] x1, [6] x1, [9] x1, [13] x2, [19] x2 [10] [11] [9] 3c 3a 3b [19] [10] [10] [6] [4] 3b 3e 3c [9] [13] Vista desde el exterior [10] [13] [10] [25] 3a Vista desde el interior 3f 3d [10] [13] 3e [10] [9] [10] [13] [9] [10] [9] [9] Vista desde el interior Alineación correcta Alineación incorrecta 3a.
4 INSTALACIÓN DE LA JUNTA INFERIOR Y LOS EMPAQUES MAGNÉTICOS • En este paso, necesitará las siguientes piezas: [5] x1, [7] x1, [8] x1 • En este paso, necesitará las siguientes herramientas: A, H 4a 4b [9] [7] [11] Vista desde el exterior [9] [5] [8] [7] 4c 4b 4d [9] [9] [5] 4e Base de ducha [5] A [7] 4f [7] [7] 4a [9] [9] H 4a. Abra el panel de la puerta [9] e instale la junta inferior [5] en la parte inferior del panel de la puerta.
5 AJUSTE DEL PANEL DE LA PUERTA • En este paso, necesitará las siguientes pieza:[27] • En este paso, necesitará las siguientes herramienta: H 5a [8] [8] [7] 5a [7] [11] [9] Ajuste incorrecto 5e [10] 5b [27] [11] [9] Ajuste correcto 5d [11] [9] [9] Umbral de la base de ducha [7] 5c [10] 5b [8] H [9] Umbral de la base de ducha 5e Ajuste correcto Ajuste incorrecto Ajuste incorrecto 5a.
6 MONTAJE DEL UMBRAL INFERIOR A LA CUBIERTA DE LA BASE • En este paso, necesitará las siguientes piezas:[18], [21] • En este paso, necesitará las siguientes herramientas: C, F Umbral de la base [20] 6a = [19] = [4] C 6b [18] 6c [21] Tornillo ST4x25 [4] [19] 3.2mm F [19] Vista desde el interior 6a. Verifique que el umbral inferior [4] esté colocado uniformemente frente a la cubierta de la base de la ducha. 6b.
7 INSTALACIÓN DE LA BARRA DE SOPORTE • En este paso, necesitará las siguientes piezas: [3], [16], [17], [18] • En este paso, necesitará las siguientes herramienta: G 7a 7b G Soporte de montaje [17] [3] [16] Soporte de montaje Tornillo ST4x35 [24] [3] 7c 7d [17] [25] [18] [3] Vista desde el interior 7e [6] [9] 7f [6] [10] [9] [10] Ajuste incorrecto [6] [9] [10] Ajuste correcto 7a.
8 INSTALACIÓN DEL JUEGO DE MANIJAS Y DE LAS TAPAS LATERALES • En este paso, necesitará las siguientes piezas: [2], [12] Vista desde el interior 8a 8c [24] 8c [9] [10] [1] [12] [2] 8a 8b 8d [9] [10] [1] [12] [2] Vista desde el interior 8a. Retire el extremo corto de la tuerca roscada y las arandelas del juego de manijas [12]. Este extremo del juego de manillas debe instalarse lo más cerca posible de las bisagras de la puerta.
9 APLICACIÓN DE SELLADOR EN LA PLACA DE CUBIERTA DE LA BISAGRA • En este paso, necesitará las siguientes herramienta: A 9a Cubierta de bisagra A 9b [13] Cubierta de bisagra Vista desde el interior 9a. Aplique el sellador [A] alrededor de la cubierta de la bisagra[13] como se ilustra. 9b. Alinee los 4 montantes de la cubierta de la bisagra [13] sobre la bisagra [13] y encaje en su sitio.
LIMPIEZA POSTERIOR A LA INSTALACIÓN AS America, Inc. (“American Standard”) garantiza al comprador consumidor original que, a opción del primero, retirará todos los desechos de construcción. La lechada de los azulejos puede retirarse usando un palito de paleta o un abate lengua de madera. No utilice cepillos de alambre ni otro implemento de metal sobre la superficie de la tina. La limpieza posterior a la instalación generalmente puede realizarse usando agua tibia y detergente líquido para vajilla.
GARANTÍA GARANTÍA POR 10 AÑOS DE LAS PUERTAS DE DUCHA AS America, Inc. (“American Standard®”) garantiza al comprador no comercial original que, a criterio exclusivo del primero, reparará o reemplazará este producto o cualquiera de sus partes, si confirma que el producto presenta defectos en los materiales o la mano de obra en condiciones de uso y mantenimiento normal por 10 años. Esta garantía es intransferible a compradores o dueños posteriores al comprador originario.
¡DÍGANOS QUÉ PIENSA! Déjenos una reseña o una historia del producto en americanstandard.com/reviews Gran tina 03/13/2018 06:52:29 CDT American Standard Tina de 60 pulg. por 34 pulg. Integral Tina con delantal. Drenaje izquierdo Amo la bañera. Es muy espacioso y definitivamente lo compraría de nuevo. Nuestra vieja bañera se rompió, así que compramos esta para reemplazarla. Este se siente como si fuera más duradero y no tan endeble como el anterior.