ACONT600AF11MA/ACONT602AF22MA Programmable Comfort Control OWNER’S GUIDE Pub. No.
Quick Reference Card Battery Holder Grasp and pull to see basic operating instructions at a glance. Press down and pull to remove batteries. Batteries should be replaced once a year (see page 17). M28618 CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). Need Help? For assistance with this product please visit www.americanstandardair.
About your new thermostat About your new Comfort Control Appendices Control features.......................................... 2 Programming at a glance........................... 3 Quick reference to controls........................ 4 Quick reference to display......................... 5 Battery replacement................................. 17 In case of difficulty................................... 18 Customer assistance................................ 20 Accessories/replacement parts...............
About your new Comfort Control Congratulations on the purchase of your new Comfort Control. It has been designed to give you many years of reliable service and easy-to-use, push-button climate control. Features • Separately programmable weekday/weekend schedules. • One-touch temp control overrides program schedule at any time. • EnergyStar compliant to greatly reduce your heating/cooling expenses. ® • Large, clear, backlit display is easy to read — even in the dark.
This Comfort Control is ready to go! Your new Comfort Control is pre-programmed and ready to go. All you have to do is set the time and day. Then check the settings below and change if needed: 1. Set time and day (required for proper operation)..........................See page 6 2. Select fan setting (Auto/On): Preset to Auto..................To change, see page 7 3. Select system setting (Heat/Cool): Preset to Heat.......To change, see page 8 4.
Quick reference to controls Digital display (see page 5). Battery holder (see page 17). Temperature Buttons Press to adjust temperature settings (see page 11-13). M28619 Function Buttons Press to select the function displayed just above each button. (Functions change depending on the task.) 69-1831—04 4 Hold Button Press to override programmed temperature control (see page 13).
Quick reference to display screen Current inside temperature In Recovery (see page 16) Current program period Wake/Leave/Return/Sleep (see pages 9-11) Set Clock/Day/Schedule (see pages 6 & 11) Low battery warning (see page 17) Inside 72 Replace Battery Wake Set Clock/Day/ Schedule In Recovery 6:30 Wed Fan Auto AM Heat Setting 72 Auxiliary Heat On System Heat Function buttons Press the button beneath each function to view or change settings (functions change depending on the task) 5 Current tim
Set the time and day Press SET CLOCK/DAY/SCHEDULE, then adjust time Set Clock/Day/ Schedule 4:30 PM Fan Auto System Heat 1. Press the SET CLOCK/DAY/SCHEDULE button, then press s or t to set the clock time. M28602 3. Press DONE to save & exit. Press SET DAY, then select current day Note: If the SET CLOCK/DAY/SCHEDULE option is not displayed, press DONE or RUN SCHEDULE. Wed Done Set Day Set Schedule M28603 69-1831—04 2. Press the SET DAY button, then press s or t to select the day of the week.
Select the fan setting Set Clock/Day/ Schedule Fan Auto Press the FAN button to select Auto or On. System Heat M28604 Set Clock/Day/ Schedule Fan System On Heat In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on. If set to “On,” the fan runs continuously. Use this setting for improved air circulation, or for more efficient air cleaning.
Select the system setting Set Clock/Day/ Schedule Fan Auto Press the SYSTEM button to select: System Heat • Heat: Controls only the heating system. M28606 • Cool: Controls only the cooling system. • Off: Heating and cooling systems are off. Set Clock/Day/ Schedule Fan Auto System Cool M28607 Note: The Auto and Em Heat system settings may not appear, depending on how your Comfort Control was installed.
Save money by setting program schedules It’s easy to program your system for maximum energy savings. You can program four time periods each day, with different settings for weekdays and weekends. WAKE 6:00 am Set to the time you awaken and the temperature you want during the morning, until you leave for the day. LEAVE 8:00 am Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).
EnergyStar® settings for maximum cost savings This Comfort Control is pre-set to use EnergyStar program settings. We recommend these settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period.
To adjust program schedules Set Clock/Day/ Schedule Fan Auto System Cool M28608 Done Set Day Set Schedule M28609 Heat Setting Set Schedule 8:00 AM 62 Leave Mon Tue Wed Thu Fri Done 1. Press SET CLOCK/DAY/SCHEDULE, then SET SCHEDULE. 2. Press s or t to set your weekday Wake time (Mon–Fri), then press NEXT. 3. Press s or t to set the temperature for this time period, then press NEXT. 4. Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period.
Program schedule override (temporary) Press to temporarily adjust temperature. Temporary Inside 69 Run Schedule 6:30 Fan Auto AM Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period. Heat Setting 75 The new temperature will be maintained only until the next programmed time period begins (see page 10).
Program schedule override (permanent) Press to permanently adjust temperature. 69 Run Schedule Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods. Heat Hold Setting Inside 6:30 Fan Auto AM 75 The “Hold” feature turns off the program schedule and allows you to adjust the thermostat manually, as needed.
Auto Changeover (heat/cool) Set Clock/Day/ Schedule Fan Auto System Auto M28613 Press until screen displays “Auto” Note: The Auto system setting may not appear, depending on how your thermostat was installed. 69-1831—04 Auto Changeover is a feature used in climates where both air conditioning and heating are used on the same day. When the system is set to Auto, the Comfort Control automatically selects heating or cooling depending on the indoor temperature.
Built-in compressor protection Cool Setting Inside 75 Set Clock/Day/ Schedule 6:30 Fan Auto AM 75 Cool On System Cool M28614 Message flashes until safe restart time has elapsed This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting.
Adaptive Intelligent Recovery (AIR) Adaptive Intelligent Recovery eliminates guesswork when setting your schedule. It allows the Comfort Control to “learn” how long your furnace and air conditioner take to reach the temperature you want. Just set your program schedule to the time you want the house to reach your desired temperature. The Comfort Control then turns on the heating or cooling at just the right time to reach your scheduled temperature at your scheduled time.
Battery Replacement Batteries are optional (to provide backup power) if your Comfort Control was wired to run on AC power when installed. Press and pull to remove Replace Battery Install fresh batteries immediately when the REPLACE BATTERY warning begins flashing. The warning flashes about two months before the batteries are depleted. M28620 Insert fresh AA alkaline batteries, then reinstall battery holder.
In case of difficulty If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank Temperature settings do not change • • • • Check circuit breaker and reset if necessary. Make sure power switch at heating & cooling system is on. Make sure furnace door is closed securely. If thermostat is battery powered, make sure fresh AA alkaline batteries are correctly installed (see page 17).
In case of difficulty Heating or cooling system does not respond • Press SYSTEM button to set system to Heat. Make sure the temperature is set higher than the Inside temperature. • Press SYSTEM button to set system to Cool. Make sure the temperature is set lower than the Inside temperature. Check circuit breaker and reset if necessary. Make sure power switch at heating & cooling system is on. Make sure furnace door is closed securely. Wait 5 minutes for the system to respond.
Customer assistance For assistance with this product call your HVAC Contractor or visit www.americanstandardair.com Or call the Customer Assistance Helpline toll-free at 1-800-500-2041. M28621 Model number XXXXXXX Date code To save time, please remove the battery holder and note your model number and date code before calling. Accessories/replacement parts XXXXXXX Battery holder............................Part No. THT02506 Cover plate assembly*..... Part No.
Limited 5-year warranty Limited Warranty Low Voltage Room Comfort Controls (Parts Only) This limited warranty is extended by the manufacturer to the original purchaser and to any succeeding owner of the real property to which the low voltage room comfort control is originally affixed and applies to products purchased and retained for use within the U.S.A. and Canada.
Limited 5-year warranty or qualified HVAC technician, (2) applied and installed in accordance with the manufacturer’s recommendations in its Installer’s Guide, and (3) in compliance with all industry standards, national, state, and local codes.
Limited 5-year warranty Some states do not allow limitations on how long an implied limited warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Parts will be provided by our factory organization through an authorized service organization in your area listed in the yellow pages.
69-1831—04 24
25 69-1831—04
6200 Troup Highway Tyler, TX 75711-9010 www.americanstandardair.com ® U.S. Registered Trademark • Patents Pending © 2008 American Standard Heating & Air Conditioning All rights reserved 69-1831—04 M.S. Rev. 11-08 Pub. No.