Installation Guide

ManualsBrandsAmerican Standard ManualsBathTown Square S 8 in. Widespread 2-Handle Bathroom Faucet with Drain Assembly and WaterSense 1.2 GPM in Legacy Bronze

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 140 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED

TOOLS

TOWN SQUARE

DUAL CONTROL

WIDESPREAD LAVATORY FAUCET

INSTALLATION

INSTRUCTIONS

74558XX

Certied to comply with ANSI A112.18.1M

M965900 (4/18)

Wrench

(Supplied)

Adjustable Wrench

Channel Locks

Flat Blade Screwdriver

Phillips Screwdriver

INSTALL SPOUT

CAUTION

Turn off hot and cold water

supplies before begining.

INSTALL VALVE BODIES

Fig. A.

• Insert SHANK (1) and HOSE (2) through center hole.

• Thread LOCKNUT (3) onto SHANK (1) from underside of sink or

mounting surface.

• Align and center SPOUT (4). Tighten LOCKNUT (3).

SPOUT BASE

Fig. A.

Fig. B.

7 Blue Stripe (COLD)

7 Red Stripe

(HOT)

Fig. B.

• Remove LOCKNUT (6) from SIDE VALVE SHANKS (5).

• Insert Hot and Cold SIDE VALVE HOSES (7),

FLEXIBLE SUPPLIES (7a) into mounting holes.

• Thread LOCKNUT (6) onto each SIDE VALVE

SHANK (5) from underside of sink or

mounting surface.

• Align and center SIDE VALVES. Tighten

LOCKNUTS (6).

Summary of content (4 pages)

PAGE 1
TOWN SQUARE® S INSTALLATION INSTRUCTIONS 74558XX DUAL CONTROL WIDESPREAD LAVATORY FAUCET Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. RECOMMENDED TOOLS Certified to comply with ANSI A112.18.1M Phillips Screwdriver Wrench (Supplied) Channel Locks Flat Blade Screwdriver 1 INSTALL SPOUT CAUTION Fig. A.
PAGE 2
INSTALL POP-UP DRAIN • Apply a bead of putty to underside of FLANGE (1). 1 2a 1 • Drop FLANGE (1) into LAVATORY DRAIN (2). From below assemble RUBBER GASKET (3), METAL WASHER (4) and LOCK NUT (5). Do not tighten. 2 3 4 5 2b 4 • Place SEAL (1) with small end facing up into TAILPIECE (2) and tighten against DRAIN BODY (4). PIVOT ROD (3) opening in TAILPIECE (2) should face the rear of the lavatory. Tighten LOCK NUT (5) with channel locks. Do not over tighten.
PAGE 3
TEST INSTALLED FITTING 1 • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. 1 • Remove AERATOR (3). • Operate HANDLE (1) to flush water lines thoroughly. 3 • Replace AERATOR (3). CHECK DRAIN CONNECTIONS • Fill lavatory with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in SINK. • Release DRAIN STOPPER (4) down and check all drain connections and “P” trap for leaks. Tighten if necessary.
PAGE 4
TOWN SQUARE® S DUAL CONTROL WIDESPREAD LAVATORY MODEL NUMBER 74558XX M970460 -YYY0A HANDLE KIT M970461-YYY0A LIFT ROD & ROD (7455.8X7) M970524 -0020A HANDLE KIT WITH RED INDEX (HOT) 7455.811/814 M970526 -0020A HANDLE KIT WITH BLUE INDEX (COLD) 7455.214/217 M923840-0070A AERATOR (1.