Instructions / Assembly

ManualsBrandsAmerican Standard ManualsBathTown Square S Single Hole Single-Handle Monoblock Bathroom Faucet with Drain and WaterSense 1.2 GPM in Brushed Nickel

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 140 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

INSTALL FAUCET

TOWN SQUARE

MONOBLOCK LAVATORY FAUCET

WITH PUSH DRAIN

INSTALLATION

INSTRUCTIONS

74551XX

Screwdriver Adjustable WrenchChannel Locks

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

COLLAR ON

MOUNTING NUT

GROOVE

(FAUCET

BASE)

MOUNTING SURFACE

Fig. C.

Fig. B.

Fig. A.

PUTTY

IF REQUIRED

M965899 (4/18)

• Installation with ESCUTCHEON PLATE: Apply a light bead of

plumbers putty to underside of ESCUTCHEON PLATE (8)

if mounting surface is uneven. Place ESCUTCHEON PLATE (8)

onto sink or mounting surface. Feed FAUCET SUPPLIES (3),

MOUNTING STUD (4) through ESCUTCHEON PLATE and

PUTTY PLATE and mounting hole of lavatory or mounting

surface. Fig. A.

• Installation less ESCUTCHEON PLATE: Seat SEAL (1)

into under side of FAUCET BASE (2).

• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4)

through the mounting hole of lavatory or

mounting surface. Fig. B.

• From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),

pulling faucet to front of sink, so SUPPLIES (3) rests against

mounting hole. Before nal tightening, make sure collar on

MOUNTING NUT (6) is seated into RETAINING WASHER (5). Fig. C .

• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)

to complete faucet mounting.

Summary of content (4 pages)

PAGE 1
TOWN SQUARE® S INSTALLATION INSTRUCTIONS 74551XX MONOBLOCK LAVATORY FAUCET WITH PUSH DRAIN Thank you for selecting American Standard... the benchmark of fine quality for over 140 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M RECOMMENDED TOOLS Screwdriver Channel Locks 1 INSTALL FAUCET CAUTION Adjustable Wrench Turn off hot and cold water supplies before begining.
PAGE 2
INSTALL DRAIN FROM BELOW FIXTURE 3 REAR OF SINK DRAIN OUTLET 1 2 3 1 2 • Thread TAIL PIECE NUT (1) clockwise onto DRAIN BODY (2). • Install DRAIN (1) by dropping it from the top of the sink. • From under side of SINK install GASKET (2) and MOUNTING NUT (3). Note: Plumber’s putty or caulk is recommended. 4 FLANGE GASKET AND POP-UP KNOB FOAM GASKET NOT VISIBLE 5 CHECK OPERATION OF POP-UP 1 DRAIN FLANGE • Operate DRAIN STOPPER (1) to verify that it opens and closes.
PAGE 3
7 TEST INSTALLED FITTING ON OFF COLD 1 • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. HOT • Remove AERATOR (3). • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). 3 CHECK DRAIN CONNECTIONS • Fill lavatory with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in SINK. • Release DRAIN STOPPER (4) down and check all drain connections and “P” trap for leaks. Tighten if necessary.
PAGE 4
TOWN SQUARE® S MONOBLOCK LAVATORY FAUCET WITH PUSH DRAIN M964369-YYY0A PLUG BUTTON & SET SCREW A918657-0070A HANDLE SCREW M918053-0070A HANDLE ADAPTER MODEL NUMBER M970455-YYY0A HANDLE KIT 74551XX M970518-YYY0A HANDLE KIT WITH RED/BLUE INDEX 7455.114/117 Replace the “YYY” with appropriate finish code M907063-YYY0A CAP M904528-0070A CARTRIDGE NUT POLISHED CHROME 002 BRUSHED NICKEL 295 LEGACY BRONZE 278 POLISH NICKEL 013 M962682-0070A CARTRIDGE M923840-0070A AERATOR (1.