Replacement Part List

ManualsBrandsAmerican Standard ManualsBathFluent Single Hole Single-Handle Bathroom Faucet in Oil Rubbed Bronze

FLUENT

™

M965621

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

MONOBLOCK LAVATORY FAUCET

with

Speed Connect™ Drain

Adjustable Wrench Flat Head Screwdriver Slip Jaw Pliers

Recommended tools

Tubing Cutter

INSTALL FAUCET

Turn off hot and cold water

supplies before beginning.

CAUTION

7186.101

GROOVE

(FAUCET

BASE)

DECK PLATE (OPTIONAL)

Deck Plate (optional)

and must be ordered separatly

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the rst time, every time.

Install SEAL (1) into groove of FAUCET BASE (2).

Feed FLEXIBLE SUPPLIES (3), SHANK (4) and

DRAIN CABLE ASSEMBLY (5) through mounting hole of

lavatory or mounting surface and optional DECK PLATE

(6) if used.

From below, Install RUBBER SEAL with RETAINING

WASHER (7) and LOCKNUT (8) onto faucet SHANK (4).

Before ﬁnal tightening, faucet should be seated ﬂush on

mounting surface.

Adjust faucet so that it is centered and covers mounting

hole. Tighten LOCKNUT (8) using a 15mm or adjustable

wrench. Do not over tighten.

LAVATORY OR

MOUNTING

SURFACE

PUTTY IF REQUIRED

Summary of content (7 pages)

PAGE 1
Installation Instructions 7186.101 FLUENT™ MONOBLOCK LAVATORY FAUCET with Speed Connect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect Drain* Deck Plate (optional) and must be ordered separatly • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. Certified to comply with ANSI A112.18.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto CABLE ATTACHMENT POINT (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 8 1-1/4” O.D. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly, refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING ON With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. 1 OFF COLD HOT Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. 3 Replace AERATOR (3). 4 CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in Sink. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 5
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
FLUENT™ MONOBLOCK LAVATORY FITTING with Speed Connect® M964933-YYY0A HANDLE KIT MODEL NUMBER M964368-OO7OA BUTTON & SCREW KIT (RED/BLUE) M964369-YYYOA BUTTON & SCREW KIT (FINISH) 7186.