Installation Guide

ManualsBrandsAmerican Standard ManualsBathSelectronic Integrated AC Powered Single Hole Touchless Bathroom Faucet with Above-Deck Mixing in Chrome

Installation Instructions

Certified to comply with ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

SELECTRONIC

Integrated Faucet with

Above-Deck Mixing

705X.105

705X.115

705X.205

705X.215

MODEL NUMBERS

Product No.'s & Options

Specifications

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Parts

3-4

5-9

9-10

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS

supplied cables, or cutting, splicing or modifying

any components will void the warranty.

M965654 Rev. 2.0 (9/16)

Summary of content (12 pages)

PAGE 1
Installation Instructions MODEL NUMBERS SELECTRONIC® 705X.105 705X.205 705X.115 705X.215 Integrated Faucet with Above-Deck Mixing CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. Product No.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. UNPACKING The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.
PAGE 3
Fig. 1 FINISHED WALL OR BACKSPLASH Roughing-in Dimensions 191mm (7-1/2) 191mm (7-1/2) 165mm (6-1/2) CLEARANCE 25mm (min) - 127mm (max) (1" min - 5" max) 140mm (5-1/2) Note: All plumbing and electrical wiring must be installed in accordance with applicable codes, regulations and standards. MOUNTING SURFACE CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty.
PAGE 4
ELECTRICAL INSTALLATION Product PWRX Power Kit (PK00.WRK) Plug-in AC Powe Kit (PK00.PAC) Fig. 1 Page 4 4 3 5 4 3 2 Hard-Wired AC Prower Kit (PK00.HAC) 5 MULTI-AC Power Kit (PK00.MAC) 5 1 A PWRX 10-Year Battery Pack Important: The 7055 series faucets come with the standard CR-P2 lithium battery installed in the faucet. No further action required. PWRK™ VERSION; 1. Connect PWRX BATTERY PACK (1) to SENSOR CABLE (2). BRACKET INSTALLATION 2.
PAGE 5
B AC VERSIONS (HARD-WIRED / Fig. 2 PLUG-IN POWER SUPPLY) ; Fig. 2 Important: Turn off power to outlet or control box. 1. Connect PLUG-IN AC POWER SUPPLY (5) or 10' EXTENSION CABLE (2) if using HARD-WIRED AC TRANSFORMER (7) to SINGLE AC ADAPTER (3). 2 10' EXTENSION 2. Connect SENSOR CABLE (4) to the other terminal of the SINGLE AC ADAPTER (3). 6 4 3. Connect PLUG-IN AC POWER SUPPLY (5) to wall outlet, or connect other end of 10' EXTENSION CABLE (2) to the HARD-WIRED AC TRANSFORMER (7).
PAGE 6
D MAKE WATER SUPPLY Fig. 4 CONNECTIONS; Fig. 4 1. Turn off hot and cold water supplies before beginning. 2. Place each SCREEN FILTER (3) on each wall supply outlet. Be sure that SCREEN FILTER (3) is inserted in the correct direction. (See Illustration) 2 BULGE SIDE DOWN 3. Connect HOT FLEXIBLE SUPPLY (marked with red stripe) (1) to hot water control stop (4). Connect COLD FLEXIBLE SUPPLY (marked with blue stripe) (2) to cold water control stop (5). Use adjustable wrench to tighten connections.
PAGE 7
B CHANGE SENSOR RANGE; Fig. 2 (Factory set at 6") Fig. 2, 3, 4, & 4a 1. Remove the FAUCET SPOUT (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET SPOUT SCREW (4) at the back of the FAUCET. Pull FAUCET SPOUT (1) up and off. Fig. 2. REMOVE 1 REPLACE 5 2. Disconnect the BLACK POWER SUPPLY CONNECTOR (1) and reconnect. Fig. 3. 3 4 2 3. While the SENSOR CONTROL LED (2) is blinking slowly, place your hand 1 - 2 in. (25.4-50.8mm) in front of the sensor. Fig.
PAGE 8
C REPLACE SENSOR; Fig. 5 Fig. 5, 6 & 7. 1. Remove the FAUCET SPOUT (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET SPOUT SCREW (4) at the back of the FAUCET. Pull FAUCET SPOUT (1) up and off. See Fig. 2 in this section. DISCONNECT WIRE CONNECTIONS 2. Disconnect both ELECTRICAL CONNECTIONS. Fig. 5. 3. Untighten SENSOR SCREW (1) with a 2.5mm HEX WRENCH. Remove SENSOR ASSEMBLY (2) from FAUCET SPOUT (3). Remove O-RING (5).
PAGE 9
D CLEAN FILTER SCREEN ON Fig. 8 SOLENOID VALVE; Fig. 8 & 9 1. Remove the FAUCET SPOUT (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET SPOUT SCREW (4) at the back of the FAUCET. Pull FAUCET SPOUT (1) up and off. See Fig. 2 in this section. 2. Disconnect SENSOR CABLE (1) from SOLENOID CABLE (2). Fig. 8. 3. Unthread SOLENOID VALVE (2) from VALVE BODY (3). Fig. 9. 4. Remove FILTER SCREEN (4) from base of SOLENOID VALVE (2). Clean and replace. Fig. 9. 5.
PAGE 10
F CHANGE HOT LIMIT SETTING FROM 95% TO 85%; Fig. 12 2 1. Remove the FAUCET SPOUT (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET SPOUT SCREW (4) at the back of the FAUCET. Pull FAUCET SPOUT (1) up and off. See Fig. 2 in this section. 3 9 2. Replace LEVER HANDLE and rotate counter-clockwise to its stop position (100% cold). Remove HANDLE. 8 SLOT 3. Pull out LIMITER STOP (1) from the VALVE STEM (2). 4.
PAGE 11
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 1 2 NO NO 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR. YES REPLACE SOLENOID WATER IS CONTINUOUSLY RUNNING RECONNECT BATTERY TO SENSOR.
PAGE 12
SELECTRONIC® Appropriate finish code CHROME Integrated Faucet with Above-Deck Mixing 002 MODEL NUMBERS 705X.105 705X.115 A912790-0070A VALVE STEM O-RINGS M964171-0070A 1.5 GPM AERATOR 705X.205 705X.215 M964172-0070A 0.5 GPM AERATOR A907405-0020A PLUG BUTTON M954483-0070A SOLENOID VALVE M964187-0020A LEVER ASSEMBLY M951479-0070A DIVERTER CARTRIDGE M911785-0070A SPOUT O-RING PWRX Power Kit PK00.