Specifications

ManualsBrandsAmerican Standard ManualsHome building and Decor7055.105

M965654 Rev. 1.2 (2/15)

Platform with Universal Sensor• Flexible Selectronic

• Easy installation. All electronics in the spout; nothing below deck

• User adjustable above-deck mixing uses ceramic disc

valve for dependability & long life

• Mixing handle can be removed for one time temperature

setting during installation

Installation Instructions

Certified to comply with ASME A112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.NOTE TO INSTALLER: Please give this manual to the customer after installation.

To l ea r n mo re ab ou t A me r ic an S ta n da rd S el ec tro ni c

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

SELECTRONIC

Proximity Integrated Faucet

with optional Above-Deck Mixing

705X.105

705X.115

705X.205

705X.215

MODEL NUMBERS

Product No.'s & Options

Specifications

Faucet Installation

Electrical Installation

Start-up / Maintenance

FAQ’s / Troubleshooting

Parts

3-4

5-9

9-10

M965654 Rev. 1.2 (2/15)

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS

supplied cables, or cutting, splicing or modifying

any components will void the warranty.

Summary of content (11 pages)

PAGE 1
Installation Instructions SELECTRONIC® MODEL NUMBERS Proximity Integrated Faucet with optional Above-Deck Mixing 705X.105 705X.205 705X.115 705X.215 • Flexible Selectronic Platform with Universal Sensor • Easy installation.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.
PAGE 3
Fig. 1 FINISHED WALL OR BACKSPLASH Roughing-in Dimensions 191mm (7-1/2) GENERAL DESCRIPTION: Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in check valves, and flexible stainless steel 16-1/4" reach inlet hose for spout connection.
PAGE 4
ELECTRICAL INSTALLATION Product Fig. 1 Page 4 DC Long Life Power Pack (7053. Series) 3 DC Standard Battery (7055. Series) 3 AC Plug-in (7056. Series) 3 2 3 4 3 AC Hardwire (7059. Series) 3 AC Multi Hook-up (7057. Series) 4 A DC VERSIONS (LONG LIFE POWER PACK & STANDARD BATTERY; Fig. 1 1 Fig. 2 Important: All product with Standard Battery come with electrical connections preaseambled (at the factory). No further action necessary. LONG LIFE POWER PACK VERSION; 1.
PAGE 5
Fig. 3 Unit #1 (Already Installed) Unit #2 Unit #3 Unit #4 4 2 3 1 MAXIMUM OF 15 UNITS PER TRANSFORMER. 10' MAXIMUM CABLE LENGTH BETWEEN UNITS. C MULTI-AC VERSION (DAISY-CHAIN); Fig. 3 Important: Disconnect the first unit’s Y-Adapter from power supply before making daisy-chain connections. Note: For Unit #1 electrical instructions, refer to section B (page 3). For subsequent Units, refer to instructions below... 1.
PAGE 6
D MAKE WATER SUPPLY Fig. 4 CONNECTIONS; Fig. 4 1. Turn off hot and cold water supplies before beginning. 2. Place each SCREEN FILTER (3) on each wall supply outlet. Be sure that SCREEN FILTER (3) is inserted in the correct direction. (See Illustration) 2 BULGE SIDE UP 3. Connect left supply (Marked with a Red Stripe) to Hot FLEXIBLE SUPPLY (1) and right supply (Marked with Blue Stripe) to Cold FLEXIBLE SUPPLY (2) supply. Use adjustable wrench to tighten connections. Do not over tighten.
PAGE 7
B CHANGE SENSOR RANGE; Fig. 2 (Factory set at 6") Fig. 2, 3, 4, & 4a 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. Fig. 2. REMOVE 1 REPLACE 5 2. Disconnect the BLACK POWER SUPPLY CONNECTOR (1) and reconnect. Fig. 3. 3 4 3. While the SENSOR CONTROL LED (2) is blinking slowly, place your hand 1 - 2 in. (25.4-50.8mm) in front of the sensor. Fig. 4.
PAGE 8
C REPLACE SENSOR; Fig. 5 Fig. 5, 6 & 7. 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. See Fig. 2 in this section. DISCONNECT WIRE CONNECTIONS 2. Disconnect both ELECTRICAL CONNECTIONS. Fig. 5. 3. Untighten SENSOR SCREW (1) with a 2.5mm HEX WRENCH. Remove SENSOR ASSEMBLY (2) from FAUCET BODY (3). Remove O-RING (5).
PAGE 9
D CLEAN FILTER SCREEN ON Fig. 8 SOLENOID VALVE; Fig. 8 & 9 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. See Fig. 2 in this section. 2. Disconnect SENSOR CABLE (1) from SOLENOID CABLE (2). Fig. 8. 3. Unthread SOLENOID VALVE (2) from VALVE BODY (3). Fig. 9. 4. Remove FILTER SCREEN (4) from base of SOLENOID VALVE (2). Clean and replace. Fig. 9. 5.
PAGE 10
F CHANGE HOT LIMIT SETTING FROM 95% TO 85%; Fig. 12 2 1. Remove the FAUCET COVER (1) by unthreading the LEVER SCREW (2) and pulling off the LEVER HANDLE (3). Unthread the FAUCET COVER SCREW (4) at the back of the FAUCET. Pull FAUCET COVER (1) up and off. See Fig. 2 in this section. 3 9 2. Replace LEVER HANDLE and rotate counter-clockwise to its stop position (100% cold). Remove HANDLE. 8 SLOT 3. Pull out LIMITER STOP (1) from the VALVE STEM (2). 4.
PAGE 11
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. NO OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES IS INTERNAL SUPPLY STOP OPEN? YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 1 2 1 NO 2 NO DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR.