Installation Guide

ManualsBrandsAmerican Standard ManualsMixing ValvesThermostatic Mixing Valve

(In Toronto Area only: 1-905-3061093)

To l e a r n more a b o u t Amer i c a n S tandard Fa u c e t s v i s i t o u r website a t : www.us.amstd.com or U.S.

customer's e-mail us at: faucetsupport@amstd.com

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-3061093)

Installation InstructionsInstallation Instructions

Certiﬁed to comply with ASME A112.18.1M

M965274

2506.192, 2506.195

SELECTRONIC®

Hard-Wired AC Powered Moments

Lavatory Proximity Faucet

PRODUCT NUMBERS

Product No.'s & Options

Speciﬁcations

How to Install

Electrical Hook-up

Maintenance

FAQ,s

Replacement Parts

2-3

4-5

6-7

Summary of content (9 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s SELECTRONIC® Hard-Wired AC Powered Moments Lavatory Proximity Faucet PRODUCT NUMBERS 2506.192, 2506.195 Product No.'s & Options 1 Certified to comply with ASME A112.18.1M © 2007 American Standard Specifications 2 How to Install 2-3 Electrical Hook-up 4-5 Maintenance 6-7 FAQ,s 8 Replacement Parts 9 M965274 NOTE TO INSTALLER: Please give this manual to the customer after installation.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Faucets Are Water Tested At Our Factory. Some Residual Water May Remain In The Faucet During Shipping. 1. Remove the fitting and loose items from the carton. The illustration below shows the fitting and all loose items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions Fig. 1 FINISHED WALL GENERAL DESCRIPTION: 154mm (6-1/16) 159mm (6-1/4) Electronic faucet with proximity operation. Vandal resistant solid brass construction single post mounting. Operates on AC permanent power. Water pressure range from 20 to 125 psi. In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in checks, and flexible stainless steel 15" reach inlet hose for spout connection. 126mm (5) 55.
PAGE 4
2 MOUNT ENCLOSURE; Fig. 2 Fig. 2 1. Determine location of ENCLOSURE (1). It must be located with-in the 14" (356mm) by 21" (533mm) shaded area shown in Figure 2 in order for electrical connections from the spout assembly to be made. NOTE: ENCLOSURE SUPPLY HOSE is 20". Distance between wall supply and ENCLOSURE (1) must be taken into consideration. LAVATORY RIM OR MOUNTING SURFACE 14" (356mm) SUPPLIES ENCLOSURE MOUNTING HOLES 1 2-3/4" (71mm) 2. Remove 4 screws from COVER (2) and pull off COVER (2).
PAGE 5
ELECTRICAL INSTALLATION Fig. 1 1 5 1 ELECTRICAL CONNECTIONS; Fig. 1 CAUTION 4 Before opening ENCLOSURE disconnect AC power supply. 1. Remove ENCLOSURE COVER (1). Fig. 1. 2. Feed the WIRE CONNECTORS (2) through the top of ENCLOSURE (5). Fig. 1a. 3. Remove GROMMET (4) from ENCLOSURE (5). Fig. 1. Fig. 1b Fig. 1a 4" 4. Feed the gray SENSOR WIRE (7) through GROMMET (4), 4" from CONNECTOR. Fig. 1b. Insert gray SENSOR WIRE (7) into SPLIT PLUG (9). Push SPLIT PLUG (9) into GROMMET (4) to seal. Fig. 1d.
PAGE 6
Fig. 2 Unit #1 Unit #2 4 TWO PIECE GROMMET 9 6 3 3 1 3 Unit #3 10 4 2 1 1 4" 1 1 5 2 FOR AC-VERSION Fig. 3a (MULTI HOOK-UP); Fig. 2, 3 TWO PIECE GROMMET 1. See AC Version Electrical Hook-up for first unit of the Multi hook-up. 8 7 2. Remove ENCLOSURE COVERS from all ENCLOSURES. 3. Remove SOLID BLACK INSERT(1) from right side of ENCLOSURE #1 and replace with gray 2-PIECE GROMMET (3). Replace solid black inserts on Unit #2 with gray 2-PIECE GROMMET (3). 2 4. Take the 10 ft.
PAGE 7
MAINTENANCE Fig 1 DETECTION ZONE 1 HAND WASH SENSOR OPERATION; Fig. 1 When the Sensor detects a user, the water immediately starts to flow. Water flow will stop Two seconds after user is out of sensor range. The off delay allows the user to comfortably move his hands without the flow cycling on to off. As a precaution, a safety timer will turn off the water, after the sensor has been blocked for 59 seconds. The water will stay off until the blockage is removed from the detection zone.
PAGE 8
4 HOW TO CLEAN FILTER; Fig. 4 CAUTION Fig.4 Before opening ENCLOSURE disconnect AC power supply. 1. Remove ENCLOSURE COVER. 2. Close SUPPLY STOP (5) with 4mm Hex wrench. Note: Keep water flowing out of faucet while shutting off. 3 3. Pull off Red (1) and Black (2) CONNECTORS from SOLENOID VALVE (3). 4 CLEAN SCREENS 4. Unthread STRAINER (4) using a 7/16" socket. 5. Pull out the STRAINER (4) and clean with an old toothbrush. Rinse thoroughly with water. 6.
PAGE 9
FAQ'S Q: How will I know if battery needs to be replaced? A: Valve does not open and sensor blinks 2 times interrupted by pause for up to 7 days. Q: Why does the faucet operate the opposite of expected-Turns On when not in sensor range, but turns off when in sensor range? A: Sensor wires to solenoid are reversed. Black to & Red to + is correct. Q: Why has the flow rate of the faucet reduced significantly? A: Check and clean aerator and strainer.