Installation Guide

ManualsBrandsAmerican Standard ManualsBathSelectronic AC Powered 1.5 GPM Single Hole Touchless Bathroom Faucet with Laminar Flow in Polished Chrome

M965651 Rev. 1.5 (10/16)

Installation Instructions

SELECTRONIC

I.C. Faucet

MODEL NUMBERS

6053.193

6055.193

605B.193

Certied to comply with:

•ASMEA112.18.1

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

ore-mailusat:CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

pleasecall(844)CRT-TEAM/(844)278-8326(InCanada:1-800-387-0369)

(InTorontoAreaonly:1-905-306-1093)

Product No.’s & Options 1

Specications 2

Faucet Installation 2-3

Electrical Installation 4-6

Start-up / Maintenance 7-8

FAQ’s / Troubleshooting 9-10

Parts 11

CAUTION: Use only American Standard supplied

transformers and cable sets. Using non-AS

supplied cables, or cutting, splicing or modifying

any components will void the warranty.

I.C. Faucet shown installed on

American Standard 9118.111 Sink

Summary of content (12 pages)

PAGE 1
SELECTRONIC® MODEL NUMBERS 6053.193 6055.193 605B.193 Installation Instructions I.C. Faucet CAUTION: Use only American Standard supplied transformers and cable sets. Using non-AS supplied cables, or cutting, splicing or modifying any components will void the warranty. I.C. Faucet shown installed on American Standard 9118.111 Sink Product No.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping UNPACKING The illustration below shows the fitting and all loose items after they have been removed from the carton. Some items may be packaged partially assembled to other items.
PAGE 3
Roughing-in Dimensions Electronic faucet with proximity operation. Vandal resistant, solid brass construction, single post mounting. Operates on DC (battery/power pack) or AC permanent power (plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/8 compression, built-in check valves, and flexible stainless steel 16-1/4" reach inlet hose for spout connection. (243mm) 9-9/16" (127mm) 5" (53mm) 2-1/8" DIA.
PAGE 4
2 MOUNT CONTROL BOX; Fig. 2 Fig. 2 NOTE: The illustration shows the Infection Control faucet mounted on the American Standard Infection Control Sink. Faucet can be installed on any sink or countertop. For futher instructions regarding faucet installation on the American Standard Infection Control Sink, see instruction sheet No. 7301793-100 (Infection Control Sink System) supplied with Sink. 1.
PAGE 5
ELECTRICAL INSTALLATION Product Fig. 1 1 Page Plug-In AC Power Kit (PK00.PAC) 6 Hard-Wired AC Power Kit (PK00.HAC) 6 Multi-AC Power Kit (PK00.MAC) 7 Fig. 1a 2 Fig. 1b 3 A DC VERSIONS ; Fig. 1 5a • PWRX • STANDARD BATTERY 5 1. Remove CONTROL BOX COVER (1). Fig. 1. 2. Feed the 27" EXTENSION CABLES (2) through the top of CONTROL BOX (3). Fig. 1a. INSTALL BATTERY 4 OR STANDARD BATTERY VERSION ONLY F 3.
PAGE 6
VERSION; Fig. 2 B AC Fig. 2 • PLUG-IN • HARDWARE CAUTION 2 Disconnect AC power supply before opening CONTOL BOX. 3 1 Note: For AC installation, make power supply connection before mounting CONTROL BOX (3) to wall. 1. Remove CONTROL BOX COVER (1). Feed the EXTENSION CABLES (2) from the Faucet through the top of CONTROL BOX (3). Install CONNECTOR LOCKING DEVICE (16). Fig. 2. FOR AC PLUG-IN ONLY 2a. Insert POWER CORD (8) through POWER SUPPLY GROMMET (9).
PAGE 7
Fig. 3 Unit #2 Unit #1 Unit #3 Already installed 10 ft. EXTENSION CABLE AC HARDWIRE POWER SUPPLY AC POWER SUPPLY OR *MAXIMUM OF 15 UNITS PER AC POWER SUPPLY. 10' MAXIMUM CABLE LENGTH BETWEEN UNITS. C MULTI-AC VERSION (DAISY-CHAIN); Fig. 3, 3a Important: All control box covers must be removed before beginning to make daisy-chain connections. Disconnect the first unit’s Y-Adapter from power supply before making daisy-chain connections.
PAGE 8
TEST INSTALLED FAUCET TION DETEC ZONE Fig. 1 TO ENSURE A LAMINAR WATER FLOW, the air must be slowly purged from the spout. To do so, cover the SENSOR (1) while slowly opening the water supply valves. When the water flows as a solid, smooth, steady stream, uncover the SENSOR (1) and fully open the water supply valve. Fig. 1. MAINTENANCE A 1 HAND WASH SENSOR OPERATION; Fig. 1 hen the Sensor detects a user, the water immediately starts W to flow.
PAGE 9
D INSTALL / REPLACE THE BATTERY or Fig. 4 PWRX BATTERY PACK; Fig. 4 CR-P2 2 1 1. Remove CONTROL BOX COVER (1). 2. Disconnect Battery Holder (3) from 27" EXTENSION CABLE (5). 3. Remove old BATTERY from Battery Holder (3). Install new BATTERY (2) making sure the terminal side i s inserted first and shape of the battery follows the shape of the BATTERY HOLDER (3). 4. Reconnect BATTERY HOLDER (3) to 27" EXTENSION CABLE (5). 5.
PAGE 10
F GENERAL CLEANING; Fig. 5 Fig.6 1. Only use a damp, soft cloth to clean the spout and the sensor. 2. For tougher dirt, use a soft cloth with diluted dish washing detergent. Wipe the area using a wet cloth. CAUTION Do not scratch the sensor when cleaning. Avoid using any abrasives or harsh detergents or chemicals. FAQ’S Q: How will I know if the battery needs to be replaced? A: Valve will not open and sensor will continuously blink 2 times interrupted by a pause, for up to 7 days.
PAGE 11
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION ARE EXTERNAL SUPPLY STOPS OPEN? NO OPEN EXTERNAL SUPPLY STOPS. NO OPEN INTERNAL SUPPLY STOP. (HEX KEY NEEDED) YES CRITICALLY LOW BATTERY. INSTALL NEW BATTERY. YES IS INTERNAL SUPPLY STOP OPEN? YES REPEATED DOUBLE FLASH ON SENSOR? NO RECONNECT BATTERY TO SENSOR. DOES SENSOR FLASH FOR 5 SECONDS? 1 2 NO NO 1 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. CHECK FOR DAMAGE TO SENSOR WIRE INSULATION. REPLACE SENSOR.
PAGE 12
SELECTRONIC® I.C. Faucet MODEL NUMBERS 6053.193 6055.193 605B.193 Appropriate finish code CHROME 002 M964142-0070A FLOW RESTRICTOR KIT PWRX Battery Pack 6053 – Series M950361-0070A PWRX BATTERY PACK M964904-0070A SENSOR KIT CR-P2 Lithium Battery 6055 – Series M950510-0070A 27" EXTENSION CABLE A923672-0070A FAUCET SUPPLY HOSE A923654-0070A BATTERY 6V CR-P2 605P400.XXX 4" DECK PLATE Plug-In AC Power Kit PK00.PAC 605P800.