Installation Instructions

ManualsBrandsAmerican Standard ManualsBathManual Clinic Sink Flush in Chrome

M965022 Rev. 2.0 (7/17)

MANUAL FLUSH VALVE

Exposed Flushometer

for 1-1/2" Top Spud Fixtures

MODEL NUMBERS

6047 Series

7017 Series

OPERATING PRESSURE:

• Overall Range: 20-125 psi **

• Recommended: 25 psi (owing) - 80 psi (static)

FLOW REQUIREMENT:

• 25gpm (94.6 L/min).

** Water pressure over 80 psi is not recommended with most

plumbing xtures

Certied to comply with:

• ASSE 1037

• ANSI/ASME A112.19.2

• ADA Compliant

NOTE TO INSTALLER: Please give this manual to the customer after installation.

To learn more about American Standard Selectronic

Products visit our website at: www.americanstandard-us.com

or e-mail us at: CRTTEAM@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call (844) CRT-TEAM / (844) 278-8326 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-306-1093)

Summary of content (7 pages)

PAGE 1
Installation Instructions MANUAL FLUSH VALVE Exposed Flushometer for 1-1/2" Top Spud Fixtures MODEL NUMBERS 6047 Series 7017 Series OPERATING PRESSURE: • Overall Range: 20-125 psi ** • Recommended: 25 psi (flowing) - 80 psi (static) FLOW REQUIREMENT: • 25gpm (94.6 L/min). ** Water pressure over 80 psi is not recommended with most plumbing fixtures Certified to comply with: • ASSE 1037 • ANSI/ASME A112.19.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping 1. R emove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Roughing-in Dimensions GENERAL DESCRIPTION FINISHED WALL Fig.1 MANUAL FLUSH VALVE Exposed Flushometer for 1-1/2" Top Spud Fixtures 38mm-127mm (1-1/2-5") SUPPLY DN 25 mm (1" I.P.S.) 6047.122 ROUGH-IN DIMENSION 686 mm (27") 108-133 mm (4-1/4" to 5-1/4") 6047.117 660 mm (26") 6047.121 ROUGH-IN DIMENSION 295 mm (11-1/2") -C-L- *CRITICAL LEVEL 6047.122 735 mm (29") 6047.117 ROUGH-IN DIMENSION 609 mm (24") 152 mm (6 " ) (Min.) 6047.
PAGE 4
1 INSTALL SWEAT SOLDER ADAPTER; Fig. 3 CAUTION Fig.3 Fig.3a FINISHED WALL Turn off hot and cold water supplies before beginning. A Note: Install Optional Sweat Solder Adapter (Supplied) for copper pipe supply line. Fig. 3. (A-B)= C 1. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture. 2. Cut the supply pipe 1-1/4" (A-B=C) shorter then the measurement taken in Step 1. File any rough edges off the end of the supply pipe. 3.
PAGE 5
4 INSTALL FLUSH VALVE; Fig. 6a & 6b Fig. 6a 3 1. As shown in Fig. 6a, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 6a. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. 2. Align the FLUSH VALVE (2) (Fig. 6b) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (6).
PAGE 6
ADJUST SUPPLY STOP; Fig. 8 Fig. 8 REMOVE COVER IMPORTANT: To avoid overflowing, the SUPPLY STOP (3) must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. The fixture and drain must be able to handle a continuous flow in case of a flush valve failure. Valve is designed to provide stated flush volume with a 25 GPM flow rate. 3 CLOCKWISE CLOSES CONTROL STOP 1. Remove COVER (2) from SUPPLY STOP (3).
PAGE 7
MANUAL FLUSH VALVE Exposed Flushometer for 1-1/2" top spud Toilets M962921-0070A CAP SEAL M970211-0021100A (MANUAL FLUSH VALVE CAP, 1.1 gpf) M970211-0021280A (MANUAL FLUSH VALVE CAP, 1.28 gpf) M970211-002160A (MANUAL FLUSH VALVE CAP, 1.6 gpf) M970211-0026500A (MANUAL FLUSH VALVE CAP, 6.5 gpf) MODEL NUMBERS 6047 Series 7017 Series M964905K-0071100A (MODEL 6047.111) M964905A-0071600A (MODEL 6047.161) M964905B-0071280A (MODEL 6047.121, 7017.121) M964905H-0076500A (MODEL 6047.117, 6047.