Installation Guide

ManualsBrandsAmerican Standard ManualsPlumbingBedpan Washer Offset Diverter Assembly, Polished Chrome

Installation Instructions

(In Toronto Area only: 1-905-3061093)

Certiﬁed to comply with:

• ASSE 1037

• CSA B125.3

• ADA Compliant

NOTE TO INSTALLER: Please give this manual to the customer after installation.

MANUAL FLUSH VALVE

with BEDPAN WASHER

M965403 REV. 1.1

MODEL NUMBERS

To lear n more about Amer i c a n S tandard Fa u c e t s v i s i t o u r website a t : www.americanstandard.com

or U.S. customer's e-mail us at: faucetsupport@americanstandard.com

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-3061093)

6047.800

6047.815

6047.820

6047.860

6047.8006047.860 6047.820

6047.815

For Use with 1-1/2" Top Spud Toilets

Summary of content (8 pages)

PAGE 1
I n s t a l l a t i o n I n s t ru c t i o n s MANUAL FLUSH VALVE with BEDPAN WASHER MODEL NUMBERS 6047.800 6047.815 6047.820 6047.860 For Use with 1-1/2" Top Spud Toilets 6047.860 6047.820 6047.800 6047.815 Certified to comply with: • ASSE 1037 • CSA B125.3 • ADA Compliant © 2013 AS America, Inc. M965403 REV. 1.1 NOTE TO INSTALLER: Please give this manual to the customer after installation. To learn more about American Standard Faucets visit our website at: www.americanstandard.com or U.S.
PAGE 2
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. 1. Remove the Bedpan Washer items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 3
Fig. 1 GENERAL DESCRIPTION: Roughing-in Dimensions FINISHED WALL FLUSH VALVE with BEDPAN WASHER For Use with Exposed Flushometer and 1-1/2" Top Spud Toilets 108mm-133mm (4-1/4" to 5-1/4") FINISHED WALL ADJUSTABLE 245mm (9-5/8") MAX. SUPPLY DN 25mm (1" I.P.S.) 358mm (14-1/16") 90˚ 708mm (27-7/8") ADJUSTABLE 207mm (8-1/8") MAX. 619mm (24-3/8") 322mm (12-11/16") 222mm (8-3/4") FOR 1-1/2" TOP SPUD FIXTURES 38mm (1-1/2") OFF-SET TAILPIECE Fig. 2 RECOMMENDED TOOLS; Fig. 2 1. 2. 3. 4. 5.
PAGE 4
1 INSTALL TAILPIECE and DOWN Fig. 3 TUBE with VACUUM BREAKER; Fig. 3 1. Slide the COUPLING NUT (3) onto the TAIPIECE (4 or 4a). Place SEAL WASHER (2) with the tapered side facing down into the COUPLING NUT (3). 5 2. Thread and tighten COUPLING NUT (3) to DIVERTER ASSEMBLY (1). 3. Slide COUPLING NUT (3a) onto the DOWN TUBE (5). Place SEAL WASHER (2a) with the tapered side facing up into the COUPLING NUT (3a). TAPERED SIDE UP 3a 2a 4. Thread and tighten COUPLING NUT (3a) to DIVERTER ASSEMBLY (1).
PAGE 5
3 INSTALL BEDPAN WASHER; Fig. 5 Fig. 5 1. Install BEDPAN WASHER ASSEMBLY (1) into SPUD ASSEMBLY (2) on fixture. Push the ASSEMBLY (1) down until the TAILPIECE (3) seats on the internal stop. Do not fully tighted SPUD COUPLING NUT (4). 2. TAILPIECE (3) may be cut to obtain the correct rough-in dimensions for flush valve. 1 3 2 4 4 INSTALLATION OF FLUSH VALVE (6047.820 / 6047.860 Only) Fig. 6 CAUTION Fig.
PAGE 6
INSTALL FLUSH VALVE; Fig. 8 Fig. 8 & 8a 3 1. As shown in Fig. 8, insert the side INLET FLANGE (1) on the FLUSH VALVE (2) into the SUPPLY STOP (3). Lubricate the INLET FLANGE O-RING (4) with water if necessary. Lightly tighten COUPLING NUT (5). Fig. 8. Important: Do not use lubricants (other than water) or any type of thread sealing paste or tape. 2. Align the FLUSH VALVE (2) (Fig. 8a) directly above the DOWN TUBE (7) and VACUUM BREAKER COUPLING NUT (6). Make sure that GASKET (10) is installed.
PAGE 7
8 FLUSH OUT SUPPLY LINES; Fig. 10 Fig. 10 1. Remove COVER (1) from SUPPLY STOP (2). Make sure supply stop is closed. 3 2. Remove FLUSH VALVE CAP (3). Pull out PISTON (4). Replace FLUSH VALVE CAP (3) and tighten. 4 2 3. With a flat blade screwdriver open SUPPLY STOP (2). to flush line of any debris or sediment. COUNTER-CLOCKWISE OPENS CONTROL STOP 4. Close SUPPLY STOP (2). Remove FLUSH VALVE CAP (3). Replace PISTON (4). Replace FLUSH VALVE CAP (3) and tighten.
PAGE 8
11 TEST INSTALLAED BEDPAN WASHER; Fig. 13 Fig. 13 1. Check alignment of FLUSH VALVE (1) and DIVERTER VALVE ASSEMBLY (2) and fully tighten all connections. 2. Push the DIVERTER ARM and SPRAY (3) down, parallel to the toilet rim. Flush the toilet to activate the SPRAY (4). 1 3. Check all connections for leaks. 4. Return the DIVERTER ARM and SPRAY (3) to the up-right position. 2 3 4 7 M965403 REV. 1.