Installation Sheet

ManualsBrandsAmerican Standard ManualsCommercial ProductsAmerican Standard Pintbrook 0.125 GPF Top Spud Urinal - Includes Flushometer

7302219-100 Rev. A 6/16

Product names listed herein are trademarks of AS America Inc.

RECOMMENDED TOOLS AND MATERIALS

Safety Glasses Tape Measure Adjustable Wrench Blade Screwdriver Pencil Levels

Thread Sealant 1/4" Ratchet Hole Cutting Equipment

BEFORE YOU BEGIN

SAVE FOR FUTURE USE

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTES:

• Pictures may not exactly define contour of china and components.

• Observe all local plumbing and building codes.

• Refer to local codes and manufacturer’s instructions for flush valve requirements.

• Carefully inspect the new urinal for damage.

• Fixture dimensions are nominal and conform to tolerances by ASME Standard A112.19.2.

• Site preparation may require additional tools and hardware.

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. (Certain installations may require professional

help.) Also be sure your installation conforms to local codes.

6002 SERIES

Top Spud

PINTBROOK URINAL

INSTALLATION INSTRUCTIONS

C/L OF

OUTLET

2" N.P.T.

FEMALE

OUTLET

CONNECTION

FINISHED

FLOOR

FINISHED

WALL

MANUAL

OVERRIDE

BUTTON

SUPPLY

DN 20mm

(3/4" I.P.S.)

419mm

(16-1/2")

366mm

(14-7/16")

13mm

(1/2")

292mm

(11-1/2")

102mm

(4")

364mm

(14-5/16")

108mm to 133mm

(4-1/4" to 5-1/4")

140mm

(5-1/2")

326mm

(12-13/16")

64mm

(2-1/2")

575mm

(22-5/8")

334mm

(13-1/8")

WALL HANGERS

(INCLUDED)

16mm

(5/8")

10mm

(3/8")

102mm

(4")

GASKET

2" N.P.T.

INSIDE THREADS

DETAIL OF OUTLET CONNECTION

FINISHED WALL

432mm (17")

MAXIMUM

610mm (24")

OPTIONAL

TO FINISHED

FLOOR

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS PINTBROOK URINAL 6002 SERIES Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. BEFORE YOU BEGIN ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
1 PREPARATION a. b. c. d. e. Turn the water supply OFF. Install or relocate the supply tubing and waste pipe as necessary to conform to the roughing in dimensions. Install the shut off valve. Install adequate support framing for the wall hangers as needed. Determine the position of the waste pipe nipple. When establishing the nipple length, take into account the length of the urinal outlet spud and the distance the female collar will thread onto the waste pipe nipple.
PAGE 3
Installation Inst ru ct io n s SELECTRONIC® DC POWERED PROXIMITY EXPOSED URINAL FLUSH VALVE 0.125, 0.25, 0.5 & 1.0 GPF MODEL NUMBERS 6063.013 6064.013 6062.601 6063.025 6064.025 6063.505 6063.051 6064.051 6063.510 6063.101 6064.101 6063.513 Exposed Flushometer for 3/4" Top Spud Urinals CLOG RESISTANT •S elf-cleaning piston valve prevents clogging and reduces maintenance. ONE SENSOR FITS ALL •O nly 1 sensor for entire Selectronic™ line of faucets, urinals, and ﬂush valves.
PAGE 4
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. UNPACKING All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. Remove the Flush Valve items from the carton. The illustration below shows all items after they have been removed from the carton.
PAGE 5
Roughing-in Dimensions Fig. 1 GENERAL DESCRIPTION: Right or Left Hand Installation SELECTRONIC™ PROXIMITY URINAL FLUSH VALVE Exposed Flushometer for 3/4" Top Spud Fixtures See (Section 5) for converting Flush Valve to Left Hand Installation. FINISHED WALL 73 mm (2-7/8") MANUAL OVERRIDE BUTTON Exclusive, self cleaning piston-type flush valve with proximity operation and manual override. Operates on DC (battery) power. Recommended operating pressure 35 to 80 psi. Can install left or right-handed.
PAGE 6
FLUSH VALVE INSTALLATION Fig. 3 FINISHED WALL 1 INSTALL SWEAT ADAPTER; Fig. 3 CAUTION A Turn water supplies off before beginning (A-B)= C Note: Install Optional Sweat Adapter (Supplied) for copper pipe supply line. CENTER LINE OF FIXTURE SPUD B 32mm (1-1/4") FILE EDGES 1. Measure the distance (A) from the finished wall to the center of the inlet spud on the fixture. 2. Cut the supply pipe 1-1/4" (A-B=C) shorter than the measurement taken in Step 1.
PAGE 7
LUSH OUT SUPPLY LINES; Fig. 6 4 F Fig. 6 2 1. Remove STOP VALVE COVER (1) from STOP VALVE (2). REMOVE COVER 2. Open STOP VALVE (2) with a flat blade screwdriver. 1 3. Turn on water supply to flush line of any debris or sediment. 4. Close STOP VALVE (2) and replace STOP VALVE COVER (1). 2 EFT OR RIGHT HAND 5 L INSTALLATION; Fig. 7 COUNTER-CLOCKWISE OPENS STOP VALVE The unit is shipped with adjustable tailpiece on the right side.
PAGE 8
MAINTENANCE Fig. 9 1 REMOVE COVER DJUST STOP VALVE; Fig. 9 A A IMPORTANT: To avoid overflowing, the STOP VALVE (3) must never be opened to the point where the flow from the valve exceeds the flow capacity of the fixture. 3 2 COUNTER-CLOCKWISE OPENS STOP VALVE 1. After installation is complete, peel off the PROTECTIVE FILM (1) from the sensor. Standing to one side, block the sensor with your hand for 10 seconds. Remove your hand and listen for audible “click” from within the valve.
PAGE 9
C REPLACE BATTERY; Fig. 11, 11a Fig. 11 1. Loosen SET SCREW (1) with 2.5mm Hex Wrench (2) in back of FLUSH VALVE COVER (3). Fig. 11. 3 1 2. Rotate COVER (3) to the right and pull off. Fig. 11. 3. T urn COVER (3) over and disconnect the SENSOR (4) from the BATTERY HOLDER (5). Remove the BATTERY CONTAINER (6) with BATTERY HOLDER (5) and BATTERY (7) inside. Fig. 11a. 2 4. Remove BATTERY HOLDER (5) from BATTERY CONTAINER (6). Fig. 11a. 5. Remove old BATTERY from BATTERY HOLDER (5).
PAGE 10
E SET DETECTION RANGE (If Required); Fig. 13 & 14 Fig. 13 Note: The detection distance is preset and ideal for most installations. Should an adjustment be required, follow the steps below. 6 1 3 1. Loosen SET SCREW (1) with 2.5mm Hex Wrench (2) in back of FLUSH VALVE COVER (3). Fig. 13a. 2. Rotate COVER (3) to the right and pull off. Fig. 13b. VIEW “A” 2 3. T urn COVER (3) over and disconnect CABLE (4) from BATTERY HOLDER (5). Fig. 13. 4.
PAGE 11
TROUBLESHOOTING FLOW CHARTS UNIT DOES NOT FUNCTION IS ANGLE STOP OPEN? NO OPEN VALVE YES CRITICALLY LOW BATTERY . INSTALL NEW BATTERY YES REPEATED DOUBLE FLASH ON SENSOR? NO 1 RECONNECT BATTERY TO SENSOR. FLASH ON SENSOR FOR 5 SECONDS? NO 1 NO 2 2 DEAD BATTERY. INSTALL NEW BATTERY. REPEAT. DAMAGED SENSOR WIRE. REPLACE SENSOR. (ONLY IF ABSOLUTELY NEEDED) YES PUSH MANUAL OVERRIDE BUTTON; WILL THE UNIT FLUSH? DAMAGED SOLENOID.
PAGE 12
SELECTRONIC® DC POWERED PROXIMITY EXPOSED URINAL FLUSH VALVE 0.125, 0.25, 0.5 & 1.0 GPF Standard Battery (6063. Series) Long Life Power Pack (6064. Series) M964942-0020130A COVER ASSEMBLY (0.125 gpf) M964949-0020130A COVER ASSEMBLY (0.125 gpf) M964942-0020250A COVER ASSEMBLY (0.25 gpf) M964949-0020250A COVER ASSEMBLY (0.25 gpf) M964942-0020500A COVER ASSEMBLY (0.5 gpf) M964949-0020500A COVER ASSEMBLY (0.5 gpf) M964942-0021000A COVER ASSEMBLY (1.0 gpf) M964949-0021000A COVER ASSEMBLY (1.