Installation Guide

ManualsBrandsAmerican Standard ManualsKitchenQuince Semi-Professional Single-Handle Pull-Out Sprayer Kitchen Faucet in Stainless Steel

Installation

Instructions

Certiﬁed to comply with ANSI A112.18.1M

4433.350

4433.350F15

CAUTION

Turn off hot and cold water

supplies before beginning.

Plumbers' Putty or Caulking

Adjustable Wrench

Phillips Screwdriver

Channel Locks

Recommended Tools

Thank you for selecting American-Standard...the benchmark

of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

SINGLE LEVER

SEMI-PROFESSIONAL

KITCHEN FAUCET

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

QUINCE™

M965242 REV. 1.5

(A) Installation with ESCUTCHEON (1). Apply a

bead of putty to bottom edge of ESCUTCHEON with

PUTTY PLATE (1). Make certain the SEAL (2) is

properly seated in recess of faucet body. Insert

SUPPLY HOSES (3) and SHANK (4) through hole of

ESCUTCHEON with PUTTY PLATE (1) and mounting

surface. Follow mounting instructions below to

secure faucet to mounting surface.

(B) Installation less ESCUTCHEON (1). Discard

ESCUTCHEON with PUTTY PLATE (1). Make certain

the SEAL (2) is properly seated in recess of faucet

body. Insert supply HOSES (3) and SHANK (4)

through mounting hole and seat SPOUT BASE onto

sink or mounting surface. Do not use putty.

Assemble RUBBER WASHER (4), METAL WASHER

(6) and threaded LOCKNUT (7) onto SHANK (3)

from underside of sink or mounting surface. Hand

tighten LOCKNUT (7).

Use a screwdriver to tighten SCREWS (8) on

LOCKNUT (7). Work your way around LOCKNUT (7),

tightening the screws slightly each time until all

are snug to ensure even pressure.

PUTTY

Summary of content (4 pages)

PAGE 1
QUINCE™ Installation Instructions 4433.350 4433.350F15 SINGLE LEVER SEMI-PROFESSIONAL KITCHEN FAUCET Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M965242 REV. 1.
PAGE 2
MAKE WATER SUPPLY CONNECTIONS BLUE STRIPE RED STRIPE Turn off hot and cold water supplies before beginning. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe) to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten. 2 Faucet supplies are 27-1/2" long from faucet base.
PAGE 3
5 SERVICE If faucet drips, operate HANDLE several times from "off" to "on." Do not apply excessive force. Clogged CARTRIDGE outlets or inlets may cause reduced flow. To clean, first turn off water supply then: Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3). Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5). Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8). Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
PAGE 4
QUINCE™ SINGLE LEVER SEMI-PROFESSIONAL KITCHEN FAUCET MODEL NUMBER 4433.350 4433.350F15 M915628-YYY0A SPOUT SPRING M964177-YYY0A SPRAY ARM M964175-0070A SPOUT BUSHING & O-RING KIT M914600-0070A SPRAY ARM BUSHING M950322-YYY220A (2.2 GPM) PULL-DOWN SPRAY M964289-0020A SPRAY HOSE AND SEALS M950322-YYY150A (1.