Installation Guide

ManualsBrandsAmerican Standard ManualsBathBaby Devoro 1.28 GPF Single Flush Toilet Tank Only in White

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

a. Close toilet supply valve and flush tank

completely. Towel or sponge remaining

water from tank and bowl.

b. Disconnect and remove supply line.

NOTE: If replacing valve, first shut off main

water supply!

c. Remove old mounting hardware, remove

toilet and plug floor waste opening to

prevent escaping sewer gases.

d. Remove closet bolts from flange and clean

away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean

and level before new toilet is installed!

SAVE FOR FUTURE USE

7301860-100

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

BABY DEVORO - 1.28 GPF TWO-PIECE TOILET

Model 2315

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product

is installed properly, please read these instructions carefully before you begin. (Certain installations may require

professional help.) Also be sure your installation conforms to local codes.

CLOSET

FLANGE

CLOSET

BOLTS

FINISHED WALL

FINISHED

FLOOR

SUPPLY

REQ'D.

10"

(254mm)

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent

damage), and install wax ring evenly

around waste flange (horn), with tapered

end of ring facing toilet. Apply a thin bead

of sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange

so bolts project through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers

marked "THIS SIDE UP" must face up!

CLOSET

BOLT

NUT

TAPERED

WASHER

FLANGE

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

INSTALL CLOSET BOLTS

Install closet bolts in flange

channel, turn 90

, and slide

into place 6" (152mm) apart

and parallel to wall.

REMOVE OLD TOILET

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE BABY DEVORO - 1.28 GPF TWO-PIECE TOILET Model 2315 Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
6 7 RUBBER GROMMET RUBBER GASKET TANK MTG. BOLTS BOLT CAP CLOSET FLANGE WASHER/NUT CLOSET BOLT WASHER NUT INSTALL TANK a. Insert rubber grommets through holes in the tank then insert bolts through holes in the grommets. b. Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening. c. With tank parallel to wall, alternately tighten nuts until tank is snugged down evenly against bowl surface.
PAGE 3
10 A Adjust Water Level To Level Indicated On Tank By Turning Water Level Adjustment Knob To Move Float Cup Up Or Down.
PAGE 4
12 TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 13. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: LIFT ARM FIRST • The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided. • The flush valve is leaking because it's worn, dirty or misaligned with tank ball or flapper (replace with a new flapper).
PAGE 5
INSTRUCCIONES DE INSTALACIÓN CUIDADO Y MANTENIMIENTO BABY DEVORO - INODORO DE 2 PIEZAS 1.28 GPF Modelo 2315 ! PRECAUCIÓN: EL PRODUCTO ES FRÁGIL. ¡MANÉJESE CON CUIDADO PARA EVITAR QUE SE QUIEBRE Y LA POSIBILIDAD DE QUE USTED SE LASTIME! NOTA: Es posible que las ilustraciones no definan exactamente el contorno de la pieza y sus componentes.
PAGE 6
7 EMPAQUE DE HULE PERNOS DE MONTAJE DEL TANQUE TAPA DEL TORNILLO DE FIJACIÓN REBORDE DEL INODORO ARANDELA TUERCA EMPAQUETADURA DE GOMA ARANDELA/ TUERCA TORNILLO DE FIJACIÓN DEL INODORO INSTALACIÓN DEL TANQUE a. Inserte los empaques de hule en las perforaciones de la base del tanque y después introduzca los tornillos en los empaques de hule. b.
PAGE 7
10 A Ajuste el nivel del agua hasta donde se indica en el tanque girando la perilla de ajuste del nivel del agua para mover el flotador hacia arriba o hacia abajo.
PAGE 8
12 SOLUCIÓN DE PROBLEMAS LEVANTE PRIMERO EL BRAZO IMPORTANTE: Elimine siempre la arena y el óxido que pueda haber en el sistema. • Compruebe que el paso de agua está cerrado. Retire la parte SUPERIOR de la válvula; para ello, levante el brazo y hágalo girar con la parte superior 1/8 de vuelta de derecha a izquierda, haciendo una leve presión sobre la tapa. • Coloque un recipiente sobre la VÁLVULA abierta para evitar derrames y abra y cierre el paso del agua varias veces. Deje el paso de agua cerrado.
PAGE 9
INSTRUCTIONS D'INSTALLATION ENTRETIEN ET NETTOYAGE BABY DEVORO - 1,28 GPF TOILETTE DEUX PIÈCES Nous vous remercions d'avoir choisi American Standard, synonyme de qualité supérieure depuis plus de 100 ans. Pour s'assurer que ce produit soit bien installé, veuillez lire ces instructions attentivement avant de commencer. (Certaines installations peuvent requérir une aide professionnelle.) Assurez-vous également que votre installation se conforme aux codes locaux. ! ATTENTION: CE PRODUIT EST FRAGILE.
PAGE 10
6 7 RONDELLE EN CAOUTCHOUC BOULONS DE MONTAGE DE RÉSERVOIR JOINT DE CAOUTCHOUC CACHE-BOULON COLLERETTE RONDELLE/ ÉCROU BOULON DE LA TOILETTE RONDELLE INSTALLATION DU RÉSERVOIR a. Insérer les rondelles en caoutchouc dans les trous de montage du réservoir puis placer les boulons de fixation. ÉCROU INSTALLER LA TOILETTE b.
PAGE 11
10 A Ajustez le niveau d'eau sur le niveau indiqué sur le réservoir en tournant le bouton d'ajustement de niveau de l'eau dans la tasse de flotteur de mouvement vers le haut ou vers le bas.
PAGE 12
DÉPANNAGE SI LA VALVE DE REMPLISSAGE SE FERME, MAIS CONTINUE TOUJOURS À FUIR LENTEMENT, répéter l'étape 12. SI LA VALVE DE REMPLISSAGE SE FERME ET S'OUVRE, MÊME LORSQUE PERSONNE NE L'UTILISE, cela indique qu'il y a une fuite d'eau parce que: • l'extrémité du tube de remplissage de la cuvette est inséré dans le tuyau de trop-plein, sous le niveau d'eau dans le réservoir.