THE BEST BATH OR SHOWER EXPERIENCE? THE ONE NOBODY INTERRUPTS. Thank you for buying an American Standard bath or shower product. We’re so grateful you did, and you will be too. Not just while you’re waking up each morning, but also every time a dirty gardener, sweaty soccer player, or muddy dog gets cleaned up. How do we know? Just like you, we’ve lived with that same beautiful chaos called life for almost 150 years.
OWNERS MANUAL Ovation Curve™ 3-piece Wall Sets 2961BWT60.011 / 2961SWT60.011 / 2961SWT48.011 INSTALLATION INSTRUCTIONS Thank you for selecting American Standard – the benchmark of fine quality for over 150 years. To ensure this product is installed properly, please read these instructions carefully before you begin. Certain installations may require professional help. INSTALLATION PREPARATION • Please unpack carefully and identify all parts needed for installation by using the Box Contents as a reference.
RECOMMENDED TOOLS AND MATERIALS Level Tape Measure 1234567891 01 1 Installation steps will indicate which tools should be used with asscociated letter 1234567891 0 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Square Pencil C D A B Painter’s Masking Tape Caulking Gun Hole Saw Safety Equipment E F G H Jig Saw with fine tooth blade Drill I J Suction Cups - optional K SOLD SEPARATELY x8 Tubes Waterproof Instant Grab Construction Adhesive x2 Tubes Tub & Tile Sealant x3 4x8' x 7/16" thic
1 ALCOVE STUD INSTALLATION NOTE: Shower walls must be installed over a combination of studs and OSB board. 60" (1524 mm) 7-3/4" (197 mm) 10-3/4" (273 mm) 10-3/4" (273 mm) 10-3/4" (273 mm) 10-3/4" (273 mm) 7-3/4" (197 mm) REQUIRED 2x4's 9-1/4" (235 mm) 30" (762 mm) 12-1/2" (318 mm) 34-1/2" (876 mm) 7-3/4" (197 mm) Alcove Stud Installation for 60" Tub or Shower Base Refer to Alcove Stud Installation illustration above for recommended 2x4 location.
2 OSB BOARD INSTALLATION 26-3/16" (665 mm) FOR 60"ALCOVES 11" (279 mm) REFERENCE CHART 7-3/4" (197 mm) REFERENCE CHART 1x4 SHOWER DOOR SUPPORT OSB BOARD REFERENCE CHART OSB BOARD 2" (50.8 mm) FROM FIXTURE DECK SCREW TO ALCOVE FRAMING BACK WALL OSB BOARD — CUT/LOCATION 2" (50.8mm) FROM FIXTURE DECK 1-1/4"(31.
3 DRY FITTING SIDE WALLS 1X4 TOP FLANGE WALL POCKET ILLUSTRATION SHOWN USING TUB ALCOVE FRAMING TILE FLANGE PROVIDE A 1/8" GAP BETWEEN DECK OF TUB/BASE. 3a. Place Side Wall into position in the alcove until corner is correctly in place, fitting squarely on top of shower base or tub with approximately a 1/8" gap. TIP: Can use paint mixing paddle as spacers for this. Check the vertical edges of the panel with a level that they are plumb. 3b.
5 FINAL DRY FIT 5a. Once all the panels are dry fitted correctly in place with no gaps, secure the bottom of each side panel to the tub/base with tape. 5b. Remove the Rear Wall Panel and mark both Left and Right Wall Panel locations, top and bottom, so when the Side Panels are removed for the addition of adhesive on the OSB board, the panels can be returned back to the same locations. 5c. Unscrew and remove both Left and Right Side Panels.
7 INSTALLATION OF EXTRUDED WALL CONNECTORS APPROXIMATE SHIM LOCATIONS POSITION WALL CONNECTOR STRIP AT TANGENT LINE OF RADIUS WALL CONNECTOR STRIP PUSH WALL CONNECTOR UP AGAINST THIS SURFACE SIDE PANEL WALL CONNECTOR STRIP FIG. A FIG. B WALL CONNECTOR PLACEMENT SIDE WALL FIG. C CUTAWAY VIEW LOOKING DOWN FROM TOP 7a. Remove one of the Extruded Wall Connectors and place onto the inside edge of one of the Side Wall Panels as illustrated (Fig. A).
8 APPLICATION OF ADHESIVE, REAR PANEL VERTICAL LINES 6" SPACING Once all panels are correctly in position, remove the Rear Wall Panel and apply adhesive on the rear OSB board around the outer edges in vertical lines with 6" spacings as illustrated. NOTE: Rear Wall Panel will use approximately 4 tubes of adhesive; if some remains after completing the application pattern, apply remaining amounts on OSB in dollops until all tubes are empty.
POST INSTALLATION CLEAN-UP Remove all construction debris. Install any accessories, shelves or doors according to manufacturer’s installation instructions. Post installation clean-up can be completed using 50/50 mixture of isopropyl alcohol and water. AFTERCARE AND CLEANING ! WARNING: Cleaning products with labels that say “not suitable for use with ABS, acrylic or polystyrene” SHOULD NOT BE USED. Read all labels carefully. Clean shower walls with warm soapy water and soft sponge.
WARRANTY SHOWER WALLS 10 YEAR LIMITED WARRANTY AS America, Inc. (“American Standard®”) warrants to the original non-commercial owner that it will, at its sole option, repair or replace this product or any part of this product, if it confirms that the product is defective in materials or workmanship under normal use and maintenance for 10 years. This warranty is non-transferable to subsequent purchasers or owners.
TELL US WHAT YOU THINK! Please leave us a product review or story at americanstandard.com/reviews Great Tub 03/13/2018 06:52:29 CDT American Standard Bathtubs Saver 60 Inch by 34 Inch Integral Apron Bathtub. Left Hand Drain Love the tub. It is very roomy and would definitely buy it again. Our old tub cracked so we got this one to replace it. This one feels like it is more durable and not as flimsy as the last one. Register your warranty and sign up for an idea-filled newsletter at americanstandard.
LA MEILLEURE EXPÉRIENCE DE BAIN OU DE DOUCHE? CELLE QUE PERSONNE N’INTERROMPT. Merci d’avoir acheté une baignoire ou une douche American Standard. Nous sommes si contents que vous l’ayez fait, vous le serez également. Pas seulement au réveil le matin, mais aussi chaque fois qu’un jardinier sale, qu’un joueur de soccer en sueur ou qu’un chien couvert de boue doit se nettoyer. Comment le savons-nous? Tout comme vous, nous vivons dans ce même désordre qu’est la vie depuis presque 150 ans.
MANUEL DU PROPRIÉTAIRE Ensemble mural Ovation Curve MC 3 pièces 2961BWT60.011 / 2961SWT60.011 / 2961SWT48.011 CONSIGNES D’INSTALLATION Merci d’avoir choisi American Standard, la référence en matière de qualité supérieure depuis plus de 150 ans. Pour vous assurer de l’installation adéquate de ce produit, veuillez lire ces consignes avant de commencer. Certaines installations peuvent nécessiter l’aide d’un professionnel. Assurez-vous que votre installation respecte les codes locaux.
OUTILS ET MATÉRIEL RECOMMANDÉS Niveau Ruban à mesurer 1234567891 01 1 Les outils à utiliser seront indiqués par la lettre correspondante à chacune des étapes de l’installation.
1 INSTALLATION DES MONTANTS POUR ALCÔVES REMARQUE : Les murs de douche doivent être installés sur une combinaison de montants et de panneaux OSB.
2 INSTALLATION DES PANNEAUX OSB 26-3/16 po (665 mm) POUR ALCÔVES DE 60 po 11 po (279 mm) TABLEAU DE 7-3/4 po RÉFÉRENCE (197 mm) TABLEAU DE RÉFÉRENCE 1x4 SUPPORT DE PORTE DE DOUCHE OSB TABLEAU TABLEAU DE RÉFÉRENCE OSB TABLEAU 2 po (50.8 mm) À PARTIR DE LA PLATE-FORME DE FIXATION SOUS-PLANCHER 1-1/4 po(31.
3 MONTAGE SANS ADHÉSIF DES PAROIS LATÉRALES 1X4 BRIDE SUPÉRIEURE POCHETTE MURALE ILLUSTRATION À L’AIDE DE LA BAIGNOIRE CADRE D’A LCÔVE BRIDE DE CARREAU PRÉVOIR UN ESPACE DE 1/8 PO ENTRE LA PLATE-FORME DE BAIGNOIRE/BASE DE DOUCHE Placez la paroi latérale dans l’alcôve jusqu’à ce que le coin soit correctement en place, s’adaptant carrément sur le dessus de la base de douche ou de la baignoire avec un espace d’environ 1/8 po.
5 AJUSTEMENT FINAL MARQUEZ L’EMPLACEMENT DES MURS LATÉRAUX 5A Une fois que tous les panneaux sont fixés sans adhésif et correctement en place, sans espace, fixez le bas de chaque panneau latéral à la baignoire/base avec du ruban adhésif, retirez le panneau mural arrière et marquez les emplacements des panneaux muraux gauche et droit, en haut et en bas, de sorte que lorsque les panneaux latéraux sont retirés pour l’ajout d’adhésif sur le panneau OSB, les panneaux peuvent être remis aux mêmes emplacements
7 INSTALLATION DES CONNECTEURS MURAUX EXTRUDÉS EMPLACEMENT APPROXIMATIF DES CALES POSITIONNER LA BANDE DE CONNEXION MURALE SUR LA LIGNE TANGENTE DU RAYON BANDE DE CONNEXION MURALE POUSSER LE CONNECTEUR MURAL CONTRE CETTE SURFACE PANNEAU LATÉRAL BANDE DE CONNEXION MURALE FIG. A FIG. B PLACEMENT DE CONNEXION MURALE PANNEAU LATÉRAL FIG. C VUE EN COUPE DU HAUT VERS LE BAS 7a.
8 APPLICATION D’ADHÉSIF, PANNEAU ARRIÈRE LIGNES VERTICALES ESPACEMENT DE 6 PO Une fois tous les panneaux correctement positionnés, retirez le panneau mural arrière et appliquez de l’adhésif sur le panneau OSB arrière autour des bords extérieurs en lignes verticales avec un espacement de 6 po comme illustré.
NETTOYAGE APRÈS L’INSTALLATION Retirez tous les débris de construction. Installez tous les accessoires, étagères ou portes, selon les consignes d’installation du fabricant.. Pour le nettoyage après installation, vous pouvez utiliser un mélange 50/50 d’eau et d’alcool isopropylique. ENTRETIEN ET NETTOYAGE ! AVERTISSEMENT: Les produits nettoyants comportant la mention «ne convient pas à l’utilisation avec ABS, acrylique ou polystyrène» NE DOIVENT PAS ÊTRE UTILISÉS. Lisez attentivement les étiquettes.
GARANTIE GARANTIE LIMITÉE DE 10 ANS SUR LES PAROIS DE DOUCHE AS America, Inc. (« American StandardMD ») garantit au propriétaire original non commercial qu’elle réparera ou remplacera, à sa seule discrétion, ce produit ou toute partie de ce produit, si elle confirme que le produit présente un défaut de matériaux ou de fabrication dans des conditions normales d’utilisation et d’entretien pendant 10 ans. Cette garantie n’est pas transférable aux acheteurs ou propriétaires subséquents.
FAITES-NOUS PART DE VOS COMMENTAIRES! S’il vous plaît laissez-nous une critique de produit ou une histoire à americanstandard.com/reviews Baignoire géniale 03/13/2018 06:52:29 HAC American Standard Économiseur de baignoire 60 pouces par 34 pouces intégral Baignoire à tablier. Renvoi à gauche J’adore la baignoire. Il est très spacieux et l’achèterait certainement à nouveau. Notre vieille baignoire s’est fissurée, alors nous avons eu celle-ci pour la remplacer.
¿LA MEJOR EXPERIENCIA DE TINA O DUCHA? LA QUE NADIE INTERRUMPE. Gracias por comprar una tina o ducha American Standard. Estamos muy agradecidos y usted también lo estará. No solo cuando se esté despertando cada mañana, sino también cada vez que se lave un jardinero sucio, un jugador de fútbol sudado o un perro embarrado. ¿Cómo lo sabemos? Tal como usted, hemos vivido con el mismo caos hermoso de la vida por casi 150 años.
MANUAL DEL PROPIETARIO Juegos de pared Ovation Curve™ de 3 piezas 2961BWT60.011 / 2961SWT60.011 / 2961SWT48.011 INSTRUCCIONES DE INSTALACIÓN Gracias por elegir American Standard, el parámetro de excelente calidad por más de 150 años. Para asegurar la instalación adecuada de este producto, por favor lea las instrucciones con atención antes de comenzar. Algunas instalaciones pueden requerir ayuda profesional. Asimismo, asegúrese de realizar la instalación de conformidad con los códigos locales.
HERRAMIENTAS Y MATERIALES RECOMENDADOS Nivel Cinta métrica 1234567891 1234567891 01 1 Los pasos de instalación le indicarán qué herramientas deben utilizarse con la letra asociada 0 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Escuadra Lápiz C D A B Cinta selladora de pintor Pistola de calafateo Taladro Sierra de perforación Lentes de seguridad E F G H Sierra caladora con dientes finos Taladro I J Ventosas – opcional K SE VENDEN POR SEPARADO x8 tubos de adhesivo de construcción de a
1 INSTALACIÓN DE LOS MONTANTES DE LA ALCOBA NOTA: Las paredes de la ducha deben instalarse sobre una combinación de montantes y tableros OSB.
2 INSTALACIÓN DE TABLEROS OSB 26-3/16" (665 mm) PARA ALCOBAS DE 60" 11" (279 mm) CUADRO DE 7-3/4" REFERENCIA (197 mm) CUADRO DE REFERENCIA OSB BOARD CUADRO DE REFERENCIA 2" (50.8 mm) DESDE LA CUBIERTA DE ACCESORIOS 1-1/4"(31.8mm) DISTANCIA DESDE LA CUBIERTA PARA 1x4 CONTRAPISO CONTRAPISO TABLERO OSB DE PARED IZQ./DER.
3 MONTAJE A SECO DE LAS PAREDES LATERALES 1X4 BRIDA SUPERIOR CAVIDAD DE LA PARED ILUSTRACIÓN CON TINA ESTRUCTURA DE LA ALCOVA BRIDA DEL AZULEJO DEJE UN ESPACIO DE 1/8" ENTRE LA CUBIERTA DE LA BAÑERA/BASE Coloque la pared lateral en su posición en la alcoba hasta que la esquina esté correctamente colocada, encajando en la parte superior de la base de la ducha o de la tina con una separación de aproximadamente 1/8". CONSEJO: Puede utilizar la paleta de mezcla de pintura como espaciador para esta tarea.
5 AJUSTE EN SECO FINAL MARQUE LAS UBICACIONES DE LOS PANELES LATERALES 5A Una vez que todos los paneles estén montados a seco y correctamente colocados en su sitio, sin huecos, fije la parte inferior de cada panel lateral a la tina/base con cinta adhesiva, retire el panel de pared trasero y marque las ubicaciones de los paneles izquierdo y derecho, arriba y abajo, de modo que cuando se retiren los paneles laterales para añadir el adhesivo en el tablero OSB, los paneles puedan volver a colocarse en las m
7 INSTALACIÓN DE LOS CONECTORES DE PARED UBICACIÓN APROXIMADA DE LOS CALCES POSICIONAR LA TIRA DEL CONECTOR DE PARED EN LA LÍNEA TANGENTE DEL RADIO TIRA DEL CONECTOR DE PARED EMPUJE EL CONECTOR DE PARED CONTRA ESTA SUPERFICIE SIDE PANEL TIRA DEL CONECTOR DE PARED FIG. B COLOACIÓN DEL CONECTOR DE PARED PANEL LATERAL FIG. C VISTA EN CORTE MIRANDO HACIA ABAJO DESDE LA PARTE SUPERIOR FIG. A 7a.
8 APLICACIÓN DE ADHESIVO, PANEL LATERAL VERTICAL LINES 6" SPACING Una vez que todos los paneles estén correctamente colocados, retire el panel trasero de la pared y aplique el adhesivo en el tablero OSB trasero alrededor de los bordes exteriores en líneas verticales con espaciamientos de 6” como se ilustra.
LIMPIEZA POSTERIOR A LA INSTALACIÓN Retire todos los desechos de construcción. Instale todos los accesorios, estantes o puertas según las instrucciones de instalación del fabricante. La limpieza posterior a la instalación puede realizarse con una mezcla de mitad alcohol isopropílico y mitad agua. CUIDADO Y LIMPIEZA ADVERTENCIA: Los productos de limpieza cuyas etiquetas indiquen “no adecuado para usar con ABS, ! acrílico o poliestireno” NO DEBEN USARSE. Lea todas las etiquetas con atención.
GARANTÍA GARANTÍA LIMITADA DE 10 AÑOS PARA LAS PAREDES DE DUCHA AS America, Inc. (“American Standard®”) garantiza al comprador no comercial original que, a criterio exclusivo del primero, reparará o reemplazará este producto o cualquiera de sus partes, si confirma que el producto presenta defectos en los materiales o la mano de obra en condiciones de uso y mantenimiento normal por 10 años. Esta garantía es intransferible a compradores o dueños posteriores al comprador originario.
¡DÍGANOS QUÉ PIENSA! Déjenos una reseña o una historia del producto en americanstandard.com/reviews Gran tina 03/13/2018 06:52:29 CDT American Standard Tina de 60 pulg. por 34 pulg. Integral Tina con delantal. Drenaje izquierdo Amo la bañera. Es muy espacioso y definitivamente lo compraría de nuevo. Nuestra vieja bañera se rompió, así que compramos esta para reemplazarla. Este se siente como si fuera más duradero y no tan endeble como el anterior.