Installation Instructions

ManualsBrandsAmerican Standard ManualsBathCadet 66" x 32" White/Chrome Freestanding Bathtub with Faucet

All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.

Local building codes vary by location. Observe all local plumbing and building codes.

Your new bath is shipped to you after careful inspection.

To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.

• Level

• Square

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

• Adjustable Wrench

• 3/32" Allen Wrench

• Hacksaw

• Sandpaper

• Screws

• Silicone Caulking

BEFORE YOU BEGIN....

TOOLS:

TOOLS & MATERIALS REQUIRED

MATERIALS:

ROUGH-IN INFORMATION:

FREESTANDING TUB

21-1/2"

(546mm)

1-1/2"

(38mm)

1" (25mm)

FROM INSIDE

EDGE OF COVER

10"

(254mm)

5-5/8"

(143mm)

4-1/16"

(103mm)

64-5/8"

(1641mm)

30-5/8"

(778mm)

FLOOR

CUTOUT

COVER

LOCATION FOR

OPTIONAL FILLER

DRAIN OVERFLOW

SAVE FOR FUTURE USE

FREESTANDING TUB

2764 SERIES

INSTALLATION INSTRUCTIONS

Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation

proceeds smoothly--please read these instructions carefully before you begin.

754782-100 Rev. F 11/14

HIGH GLOSS ACRYLIC SURFACE

NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.

66 x 32 x 23 In. (TUB ONLY)

(1 676 x 813 x 584 mm)

120 Lbs. (54 Kg)

600 Lbs. (272 Kg)

58 Gal. (220 L)

47.25 x 20.5 In. (1200 x 521mm)

56.25 x 23.25 In. (1429 x 591mm)

14.625 In. (371mm)

79 Lbs./Sq.Ft. (386 Kgs/Sq.m)

GENERAL SPECIFICATIONS FOR

2764 SERIES TUBS

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL TO OVERFLOW

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FREESTANDING TUB 2764 SERIES HIGH GLOSS ACRYLIC SURFACE Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. BEFORE YOU BEGIN.... Local building codes vary by location. Observe all local plumbing and building codes. Your new bath is shipped to you after careful inspection.
PAGE 2
1 INSTALLATION INSTRUCTIONS: A. Set up the cover in the desired location. Locate the drain outlet location and supply line locations for the faucet (see faucet instructions). B. Recommend cutting floor cutout - 10" x 5-5/8" (254mm x 143mm) use cover as guide, as shown in rough-in detail. C. Mark lines on the floor for the cover location. Use these to relocate cover. D. Turn the cover over and apply silicone caulking to the bottom of the cover as shown. 2 3 A.
PAGE 3
DRAIN Step 2 DRAIN Step 3 Install Overflow Assembly (H) using supplied Round Gasket (E), Flange Ring (F) and Brass Overflow Nut (G). Finger tighten Brass Overflow Nut (G). Install Drain Shoe (D) using supplied brass Drain Bolt (A), Strainer (B) and Gasket (C) as illustrated. Tighten Drain Bolt (A) to secure. Do not overtighten or Drain Shoe assembly may be damaged. Note: Brass Overflow Nut (G) to be tightened further upon completion of Step 4. Note: The top tub lip MUST be level.
PAGE 4
DRAIN Step 7 TEST DRAIN OPERATION BY TURNING OVERFLOW HANDLE AS FOLLOWS: TO OPEN DRAIN: TO CLOSE DRAIN: Turn knob 1/8 turn clockwise (K). Turn knob 1/8 turn counterclockwise (L). DRAIN KNOB DRAIN KNOB 1/2"-5/8" K OPEN 4 1/2"-5/8" K OPEN A. Apply silicone caulk to the bottom of tub as shown. B. Place tub into cover. Make sure to evenly center the tub onto the cover. The gasket will be compressed between the tub and cover. 5 6 A.
PAGE 5
POST INSTALLATION CLEAN-UP Remove all construction debris from bath. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.