Installation Guide

ManualsBrandsAmerican Standard ManualsBathStudio S 1-piece 1.0 GPF Single Flush Elongated Low-Profile Toilet in White Seat Included

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench

Hacksaw Wax Ring/Gasket Closet Bolts

Sealant Tape Measure Carpenters Level

ITEMS INCLUDED

x1 T-Handle

x2 T-Bolt Nuts

SAVE FOR FUTURE USE

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

Low Profile Studio

S Toilet

Model 2548A - Elongated, Right Height

with Seat

7302429-100 Rev. 1 2/20

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 140 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. (Certain installations may require professional

help.) Also be sure your installation conforms to local codes.

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

IMPORTANT:

Water supply on the wall is required at 10" (254mm) minimum from centerline of the toilet. See rough-in for outside toilet supply line installation.

For behind toilet or hidden supply line installation, install supply at centerline of toilet 11-1/2" (292mm) above finished floor using 'compact' 1/2"

1/4 to 1/2 turn shutoff valve.

NOTE: Depending upon the compact 1/4 turn supply valve purchased, ensure it will correctly fit and operate at the location behind the trap way

inside the toilet!

Check your supply and hose dimensions. Requires a 1/2" (13mm) Supply Valve and Hose.

The geometry of the toilet gives space for these 2 supply line installation locations.

20" x 1/2" Flexible Supply Hose for outside and inside installation of toilet supply line.

Standard 1/2" Supply valve for outside toilet installation or 1/2" 1/4-1/2 turn compact

supply valve for behind or hidden supply line installation.

REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

Two water supply line locations are suggested with this toilet, outside of toilet or behind toilet locations.

Water supply valve will need to be relocated. Refer to roughin for water supply locations suggested.

SUPPLY

LINE

1" (25 mm)

16-1/2"

(419 mm)

31-1/8"

(790 mm)

5-1/2"

(140 mm)

15-3/8"

(392 mm)

16-3/8"

(416 mm)

12"

(305 mm)

11-1/2"

(292 mm)

FINISHED WALL

FINISHED FLOOR

FINISHED

FLOOR

10"

(254 mm)

18-1/2"

(468 mm)

BEHIND TOILET

SUPPLY LINE

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Low Profile Studio® S Toilet Model 2548A - Elongated, Right Height® with Seat Thank you for selecting American Standard - the benchmark of fine quality for over 140 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
3 4 INSTALL CLOSET BOLTS Install closet bolts in flange channel, turn 90°, and slide into place 6" (152 mm) apart and parallel to wall. CLOSET FLANGE INSTALL WAX SEAL WAX RING Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet.
PAGE 3
7 INSTALL TOILET a. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. ! CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! b. Once toilet is fully installed and flange nuts secured, carefully turn the Regulator to the right (clockwise). This will give additional clearance to connect the supply line coming from behind the toilet to the Regulator.
PAGE 4
REMOVING/CLEANING REGULATOR Depending upon the water quality or debris that can come into the toilet from the water supply, it may be necessary to remove and clean the "Inlet Strainer" in the Regulator to ensure the toilet flushes correctly. a. Shut off water supply to toilet. b. Remove Rear Seat Cover. c. Disconnect water supply hose on Regulator end. (reference Figure 1 in Step 5.) d. Turn Regulator Counter Clock Wise (to the left) and remove regulator. e.