VOLTEX 50 RV PLUS User Guide RV Cellular Signal Booster
This publication provides instructions for installing Cellular Signal Booster VOLTEX 50 RV PLUS. Copyright© 2018, American Booster Inc. All Rights Reserved. Revision History Date Version Changes 2018, October Version 1.0 Original 2019, February Version 1.1 Certification This equipment complies with the FCC / IC directives. Technical Support : 913 469 6699 www.americanbst.
INDEX Product Introduction 4 Package Contents 5 Installation Guide 6 Step 1. Mount the Outside Antenna 6 Step 2. Connect Cable to the Outside Antenna 7 Step 3. Install the Signal Booster 8 Step 4. Install the Inside Antenna 9 Step 5.
VOLTEX 50 RV PLUS The American Booster® VOLTEX 50 RV PLUS has been designed to provide an advanced solution for boosting your signal and increasing the cellular data speeds in your vehicle. How it works Receives Signal The signal booster’s outside antenna receives voice and data signals from a nearby cell tower. 4 Boosts Signal The signal booster receives the signal from the outside antenna and amplifies the voice and data signals.
Package Contents Signal Booster VOLTEX 50 Code No. : 835T7 Inside Antenna Kit Code No. : 835TF Outside Antenna Kit Code No. : 835TG 5D-FB Cable, (N-SMA) AC/DC Adapter Code No. : 835U3 Hardwire Power Cable Code No. : 836HW Coaxial Cable 20 ft. Code No.
Installation Guide Step 1. Mount the Outside Antenna Choose where you want to have the outside antenna on your RV and make sure the antenna is in a location within the reach of the booster with a 20 ft. coaxial cable. We would recommend mounting the outside antenna on the pole or ladder of your RV.
Step 2. Connect Cable to the Outside Antenna Assuming you don't have any holes, drill a 1 inch hole on your RV for the coaxial cable to pass through the RV and connect the outside antenna to the booster. 1 2 1 inch bit hole WARNING Check if there are no wires, pipes or cables that can be damaged while drilling a hole.
Step 3. Install the Signal Booster 1 Find a place to install the booster. 2 3 From outsid e antenna From inside anten na Mount the bracket. Snap the booster into the bracket. 8 Connect the cables.
Step 4. Connect Inside Antenna to the Booster Place the inside antenna close to your phone or tablet for an optimal performance.
Step 5. Power up the Booster Connect the AC/DC power adapter to the booster and plug into a power source. The power LED will light, indicating that the signal booster is ready for use. Note We provide hardwire DC power cable option as well.
Booster Performance The Booster's performance depends on the signal strength you are receiving through outside antenna.
LED LED Indicators Flashing Green After the Signal Booster is powered on, flashing green will last for 20 seconds. It means that the Signal Booster is being set up for an optimal performance. The Signal Booster will need a few minutes to adapt to the network environment and start boosting the signal at the highest power. The Signal Booster provides real-time self-diagnosis, so in case of flashing or solid red, refer to the Troubleshooting instructions on the next page.
Troubleshooting Instructions to fix flashing or solid red. If you have a good voice signal and fast data speeds even though one or two of LEDs are solid red, you may continue to use the Signal Booster as it is. However, if one of the LED’s has flashing or solid red, your voice signal is weak and data speeds are low, then follow the troubleshooting steps below. 1. Unplug the Signal Booster’s power adapter. 2.
Antenna Kit Options Inside Antenna Options Code No. : 835TF Desktop Antenna with 17 ft. RG58_SMA (Male) cable Code No. : 835LH Patch Antenna with 10 ft. RG174_SMA (Male) cable Outside Antenna Options Code No. : 835LL Magnetic Antenna with 13 ft. RG174_SMA (Male) cable Code No. : 835TG Omni Antenna with N Connector Recommended to use with 5D-FB 20 ft. 50Ω N (Male) to SMA (Male) coaxial cable_8368J Code No. : 836C9 Marine Antenna with 13 ft. RG58_SMA (Male) cable Code No. : 837C4 Truck Antenna with 13 ft.
Specifications Parameter Downlink 700MHz LTE 734MHz ~ 757MHz 800MHz Cellular 1900MHz PCS 2100MHz AWS Composite Power Maximum Gain Noise Figure Impedance RF Connector Power Connector Power Size, inch Weight, lbs Operation Temperature Humidity 869MHz ~ 894MHz 1930MHz ~ 1995MHz 2110MHz ~ 2155MHz 5dBm Uplink Remark 704MHz ~ 716MHz 776MHz ~ 787MHz 824MHz ~ 849MHz 1850MHz ~ 1915MHz 1710MHz ~ 1755MHz 23dBm Band 17 & 13 Band 17 Band 5 Band 25 Band 4 50dB 5dB nominal 50 Ohm SMA Female DC-045B DC 12V / 3A 5
Safety Guidelines WARNING ELECTRIC SHOCK Opening the Signal Booster could result in electric shock and may cause severe injury. DAMAGE TO EQUIPMENT Use only the power supply provided in this package. Operating the Signal Booster with antennas in very close proximity facing each other could lead to a severe damage to the Signal Booster. CAUTION THE SIGNAL BOOSTER SHOULD BE INSTALLED AS CLOSE AS POSSIBLE TO THE POWER SOURCE.
FCC Warning Statements FCC Part 15.105 statement Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IC Warning Statements RSS-GEN, Sec. 7.1.2 – (transmitters) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
WARRANTY Opening or tampering with the Signal Booster will void all warranties. American Booster provides a 2-year warranty with all of its equipment. Every product of American Booster is guaranteed to be free of material defects or component malfunctions. This warranty does not cover to any Signal Boosters that have been exposed to any misuse, abuse, physical damage or inadequate maintenance.
www.americanbst.
