080P Wi-Fi Video Doorbell User Manual V 1.0.
Table of Contents Legal Statement.................................................................................................. 2 Important Safeguards and Warnings......................................................... 3 Device Introduction........................................................................................... 4 Physical Installation........................................................................................... 9 Amcrest Smart Home App Setup.............................
Legal Statement Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Important Safeguards and Warnings The following description is the correct application method for the device. Please read the manual carefully before use to prevent damage or property loss. Operating Requirements • Do not place or install the device in an areas of high exposure to direct sunlight or near high heat generating devices. • Do not install the device in areas of high humidity, dust, or fuliginous areas.
Device Introduction What’s Included? Wi-Fi Doorbell 2 Faceplates Mounting Bracket Chime Kit 4 Mounting Screws 2 Terminal Screws Bracket Screw 2 Extra Wires Wire Connector 2 Wire Nuts 4 Wall Anchors Wire Harness 2 Wire Extenders Screwdriver NOTE A 15/64 masonry drill bit will be required if installing on concrete stucco or brick.
Front Panel The front panel of the device includes PIR detection sensors, IR lights, camera, microphone, speaker, indicator light, and a call button. PIR sensor Camera IR Lights Speaker Indicator Light Call Button Microphone Indicator Light Description The indicator light on the front of the device will display specific status details of the device. For a description of each status please refer to the information provided below.
Rear Panel The rear panel of the device includes a microSD card slot, reset/config button, as well as power input ports which act as a power terminal for your device. Reset/Config Button MicroSD Card Slot Power Input Ports Reset/Config Button • The reset/config button will be used to establish an initial connection during setup. When pressed the device will broadcast a hotspot connection which will be used to connect the device to the mobile app.
Mechanical Chime Wiring Diagram AC Power Mechanical Chime Chime Kit Electronic Chime Wiring Diagram AC Power Electronic Chime Chime Chime Kit Kit Wireless Chime Wiring Diagram For systems using wireless chimes the included Chime Kit is not required. Please see diagrams listed below for more details.
DC Power Bottom The bottom of the device houses a screw hole and a security screw. These are used to secure the device to the included mounting bracket during physical installation.
Physical Installation Before physically installation, please ensure the proper voltage is present in the area you are installing the device. The voltage at the install sight should range between 16V~24V AC to function. If proper voltage is not available, it is highly recommended to contact a licensed electrican to complete the physical installation of your device. The Amcrest Wi-Fi video doorbell does not require a chime to function as long as adequate voltage is being applied to the device.
Locate and Loosen the Screws on your Chime Using the included screwdriver, loosen the screws labeled “FRONT” & “TRANS”. Note: Be careful not to detach or remove the existing wiring. Connecting the Chime Kit Slide the connecting wires from the Amcrest Chime Kit underneath the screws, then retighten the screws. It doesn’t mattery which wires connect to which terminal. Replace the Chime Cover Secure the Amcrest Chime Kit using the included adhesive.
Installing the Wi-Fi Doorbell Everything you need for the installation of your Amcrest Wi-Fi doorbell is included in the box, however, a 15/64 masonry drill bit may be required if installing the device on concrete, stucco or brick. Remove the Faceplate and Bracket 1. Place your fingers in the indentations on the sides of the doorbell, simultaneously pull away and push the faceplate out. 2. Use the included Philips head screwdriver to remove the bracket screw from the doorbell.
Connect Doorbell to Existing Wiring Loosen the terminal screws located on the back of your Wi-Fi Doorbell using the included Phillips head screwdriver. Place your existing doorbell wiring underneath the terminal screws, then re-tighten the terminal screws to secure the wires. NOTE If your existing doorbell wiring is too short, use the included extra wires and wire nuts to extend your wiring. Remove the terminal screws completely then thread the screws through the extra wire.
Turn the Breaker Back On The physical installation is now complete. Turn your breaker back on and the allow the doorbell to power up. It may take the doorbell up to 2 minutes to fully power up. Now it’s time to setup the Amcrest Smart Home App. Amcrest Smart Home To connect your Amcrest Wi-Fi doorbell to your Android or iOS mobile device, download the Amcrest Smart Home app and follow the instructions in the app setup.
Scan the QR Code Scan the QR Code on the back of the doorbell or manually enter the serial number for the device by tapping “Manually enter S/N”. The serial number can be found on the serial tag on the back of the doorbell or on the side panel of the doorbell box. Choose Your Wi-Fi Network Select your Wi-Fi network from the Wi-Fi network list. Enter the password for your home Wi-Fi network. If you would like to save this password to the app, tap on “Save Password” Tap “Connect” to continue.
Chime Settings Amcrest doorbells can only link up to one electronic or one mechanical chime. For more information on linking a chime, refer to “Linking a Chime”. Tap “Next” to continue. Set the Time and Date Live View Set “Time Zone” to your current time zone and set “DST” (Daylight Savings Time) settings if applicable. The main screen will be your devices menu. This is a menu that will display all connected devices and well as quick access to certain settings for your doorbell.
Answering the Door When someone is at the door, you can use these features: MUTE HANG UP Mute or unmute the call. Hang up to end or ignore the call. ACCEPT Tap accept to talk to visitors at the door. Linking a Chime This is only necessary if you have an existing chime system and have installed the chime kit. If you do not link the chime to the Amcrest Smart Home app, the doorbell will not link with your chime.
Multiview The multiview option is used to view up to 4 devices simultaneously on the live view screen. To access the multiview menu, tap on the Multiview icon located on the live view interface. Add a Device Select your Device View Your Devices Tap on the ( + ) icon to begin adding optional devices to the live view screen. Select your device from the optional channels menu. The interface can view up to 4 devices simultaneously.
Full Screen The fullscreen option allows you to view a full screen view of the live feed from your device. When in full screen mode, tap the live view screen to access the live view features for your device. To exit full screen mode, tap on the back arrow ( < ) to revert the live feed back it its original format. HD/SD The HD/SD button will set the live feed for your device in standard definition or high definition.
Manual Snapshot/Record The snapshot and record button allow you to manually take snapshots or video of the live feed. All manual snapshots and videos will be stored in the My Saved Files folder located in the Account section of the Amcrest Smart Home app. Take a Snapshot My Saved Files View you Photo Tap on the Snapshot button to manually take a snapshot of the live view screen. To view the snapshot, use the back arrow ( < ) to access the devices menu.
Amcrest Smart Home Cloud The Amcrest Smart Home Cloud is an optional premium cloud storage service that offers a wide range of storage options for cloud users who wish to have secure cloud based options for their recordings. This is different from Amcrest Cloud service as the Amcrest Smart Home cloud is exclusive to Amcrest Smart Home devices and will not be compatible with other traditional or legacy Amcrest IP cameras or devices.
Amcrest Smart Home Cloud Plans Explained Amcrest offers a wide range of options for cloud users who wish to have secure cloud based options for their recordings. These include our free 1 year cloud plan which offers 3 days of motion detection storage with a 12 second record time and 7 minute cool down to a 30 day motion detection storage plan that offers unlimited recorded as well as no cool down.
Downloading Recordings Due to the current capabilities of the app recordings can only be downloaded via the Cloud Recordings download interface. All recordings retained on a microSD card will have to be downloaded via a microSD card adapter (sold separately) on a computer. For more information on microSD card recordings, please refer to the microSD card section of this manual.
Access Your Account Access Plan Details Change Current Plan Open the Amcrest Smart Home app and log into your account. Tap on My Plans. Select your current plan from the My Plans menu. Tap on the Account tab. Update Cloud Plan Read the provided information on the screen and tap "Change Plan" to continue. Note: The My Plans menu will display all past and present Amcrest Smart Home Cloud plans, unpaid, paid as well as cancelled plans. You can filter this via the "Unpaid", "Paid", and "Cancelled” tabs.
MicroSD Card Recordings This device is capable of providing local storage via an external microSD card (sold separately). Please ensure you are using a class 10 or above microSD card that does not exceed the storage limitation of your device. The microSD card must be formatted to FAT32. This may have to be done manually as most programs do not format to this allocation automatically. When a microSD card is inserted into the device, all motion based recordings will be stored to it.
App Settings The settings menu for your device allows you to configure specific settings such as device information, motion detection, time zone, Wi-Fi and other related settings. All settings are based on the capbilities of the device and may differ between certain models. Please refer to the information below for more information on the settings available for your device. Accessing the Settings Menu The settings menu for your device can be accessed via the live view menu.
Device Information This menu allows you to update the thumbnail image, name, and password for your device. The model number, serial number and other useful information can be accessed via this menu. Tap on Device Thumbnail to update the thumbnail image for your device. The thumbnail can be default, a manually taken snapshot, or uploaded from your smartphone. Tap on Device Name to edit the name of your device. Tap on the Save icon ( ) when finished.
Motion Detection Overview Amcrest Smart Home devices allow you to view motion detection recordings locally, using a microSD card (sold separately) or via Amcrest Smart Home cloud which is a cloud based service where you can remotely view and store motion detection recordings. By default, motion detection is automatically enabled on all Amcrest Smart Home devices. All motion detection settings are adjustable using the Amcrest Smart Home app.
Motion Detection Schedules A motion schedule allows you to set the device to begin recording motion detection events at a designated time. This is useful if you would like the device to only start detecting motion during specific times of the day. If you would like the device to record motion 24/7 you can leave the schedule as default. However, for more information on how to set a motion schedule, please refer to the information provided below. Tap on Motion Schedule.
A blue check mark will be displayed next to the active days. Tap the back arrow ( < ) to exit. Tap on the “Save” button to save your motion schedule. The motion schedule is now applied to your device. Tap the back arrow ( < ) to exit. Motion Sensitivity Motion sensitivity allows you to adjust how sensitive the motion detection will be for your camera. This is based off a minimum and maximum value ranging between 1, having the least amount of sensitivity, and 6 being the max.
Setting Motion Detection Zones Setting motion detection zones allows you to customize activity zones for motion detection areas. This helps to block out and avoid false motion events and is useful for blocking out areas such as trees, bushes, or other areas to avoid To set a motion detection zone, tap on "Clear Zone". Use you finger to highlight the area(s) on the screen that you would like to block motion detection events. Tap on "Save Zone" to save the motion detection zone.
In the account menu, scroll down to the "Push Notification" menu. You will notice 2 toggle switches, one for your devices and one for shared devices. Use these toggle switches to turn smart notifications on or off for your devices or for shared devices. If you would like to turn off motion detection events you can based on device in the Devices menu. To turn off motion events per device toggle the "running man" icon ( ) to the off position.
Storage Status The storage status menu displays any current cloud or microSD card storage options applicable for your device. This option also allows you view current cloud subscriptions applicable to your device as well as format a microSD card right from your smartphone. To access the Storage Status menu, tap on the settings icon ( ) on the live view screen. Tap on the Storage Status option located in the settings menu. The microSD card storage capacity will be displayed in this menu.
Share Device Device sharing allows you to add specific Amcrest Smart Home users to share the live feed of your added device. When you add a shared user, the shared user will have access to your camera and features such as live viewing, recording, playback, and two-way audio. Note: The maximum users allowed on a shared account is 6 users. To access the Share Device menu, tap on the settings icon ( ) on the live view screen. Tap on, "Add a Shared User".
Firmware Update This menu allows you to update the firmware for your device. If a firmware update is available, a red dot will be displayed in this field. It is highly recommended to keep the firmware for your device up to date at all times. To access the Firmware Update opton, tap on the settings icon ( ) on the live view screen. Locate the Firmware Update option. If a firmware update is available there will be a red identifier prompting you that a firmware upgrade is ready.
Reboot The reboot option allows you to reboot your device from the Amcrest Smart Home app. To access the Reboot option, tap on the settings icon ( the live view screen. ) on Tap on the Reboot option and tap “Yes” to continue. The reboot process will take up to 3 - 5 minutes to complete. Allow the device to reboot before accessing the live feed or other related options. Doorbell Tones & Volume This menu allows you to adjust the chime volume and well as speaker volume of the doorbell.
Delete Device The delete device option allows you to unbound and remove the device from your Amcrest Smarthome account. This option is useful if performing a factory reset on the device or setting up the device in a new location. To access the Delete Device option for your device, tap on the settings icon ( ) on the live view screen. Scroll down to the bottom of the settings menu and tap on the Delete Device option. A prompt will appear asking if you are sure you would like to delete the device.
Events Menu The events menu provides quick access to system and device related security and system alerts. The security alerts menu provides information on how many push notifications were sent, per device, per day and provides a way to view each notification that was sent within a 7 day period. The system notification menu retains notifications provided by the developer. This can range from system maintenance messages to firmware update reminders for your device.
Account Menu The accounts menu allows to view and update general account information as well as customize and adjust specific settings for your device. For more information on the options available in the account menu, please refer to the information provided below. To access the Account menu, open the Amcrest Smart Home app and log into your account. Tap on the Account menu option located at the bottom of the interface. All account based options for your account will be displayed in this menu.
The Cloud Downloads menu allows you to view, delete, or download cloud recordings that were downloaded from the cloud recordings interface. Tap on a clip to view the recording, use the trash can icon to delete it, tap on the download button to download the recording to your mobile device. The My Saved Files menu allows you to view, delete, rename, share, and export manually recorded snapshots or videos. Use the video/snapshot icons to view the manually recorded files.
The Leave Feedback allows you to leave feedback to improve the overall experience of the Amcrest Smart Home app. We take this feedback seriously and are always looking for new ways to improve your experience. The About tab allows you to view the current app version you are using as well as a link to our privacy policy. Push Notifications The push notification toggle switches located in the account menu enable and disable push notifications for every device connected to your Amcrest Smart Home account.
Setting a Push Notification Schedule A push notification schedule can be setup which will allow the app only to send push notifications to your device or a shared user’s device during a specific time during the day. For more information on how to setup a push notification schedule, please refer to the information provided below. In the account menu, tap on the Schedule option in the Push Notification menu to display the push notification schedule menu.
Fingerprint Verification The fingerprint verification option allows you to set a fingerprint authentication that will allow you to log into your Amcrest Smart Home app using your fingerprint. Please note, this option will only be applicable to smartphone devices that have fingerprint capabilities. In the accounts menu, tap on the “Fingerprint Verification” toggle switch to enable or disable this feature. A fingerprint must be enabled first on your smartphone before this option can be enabled.
Adding to Blue Iris Amcrest Smart Home devices such as the Amcrest Wi-Fi Doorbell Camera can connect the Amcrest Smart Home app as well as to Blue Iris. This is possible by obtaining the IP address of your device from your network and adding it directly to the software using RTSP. The doorbell must be set up first using the Amcrest Smart Home app before adding it into any additional software. Please note: The doorbell and the computer you are using must be on the same network during setup.
Adding to Amcrest NVR/DVR Most Amcrest Smart Home devices, excluding Smart Home battery cameras, can connect to both an Amcrest DVR and Amcrest NVR. This is possible by obtaining the IP address of your device from your network and adding it directly into your DVR or NVR. The DVR or NVR must be connected to the same network as the Amcrest Smart Home device for this to work. The device you are adding must be added to the Amcrest Smart Home app first before adding it to your device.
Adding to Amcrest View Pro Amcrest Smart Home devices such as deterrent cameras, doorbells, or other related Amcrest Smart Home devices, excluding battery cameras, are capable of connecting to both the Amcrest Smart Home app as well as the Amcrest View Pro app.
Technical Specifications 46
Troubleshooting Installing Without an Existing Chime System? The Amcrest Wi-Fi doorbell requires a 16V~24V AC power connection to function. If new wiring is being installed for your doorbell a third party transformer with 16V~30Va would be efficient to use for installation. Amcrest does not currently sell its own brand of transformers for the doorbell. The Amcrest Wi-Fi doorbell does not require a chime to function as long as adequate voltage is being applied to the device.
Unable to Locate an SSID? If you are having issues obtaining an SSID when adding your device into the Amcrest Smart Home app there may be a miscommunication happening between the app and your mobile device. This appears to be a more common situation among iOS users and we are currently working with Apple to device a solution. There is an easy fix you can use to resolve the issue. For more information on how to resolve this issue, please refer to the information provided below.
