Operating instructions

ManualsBrandsAmbient ManualsRemote ControlTOUCH LIGHT

50D0092 Rev 4 Feb 2005 Page 1 of 9 Ambient Technologies

ADivision Of

TLM

TOUCH LIGHT™ On/Off Remote Control

INSTALLATION AND OPERATING INSTRUCTIONS

This wireless wall on/off/ remote control – system provides a safe, reliable, and user-friendly remote control for

millivolt valve gas appliances. The system can be manually turned on and off with the transmitter. Always check

the appliance home owner’s manual for additional information, or warnings regarding accessory installation before

connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately contact the

dealer from whom you purchased the kit. Do not attempt to install any part of the kit unless all parts are in good

condition. Please keep this booklet for future reference.

CONTENTS OF KIT

Description Qty

Touch Light Transmitter 1

Battery Alkaline AA (for Transmitter and receiver) 6

Receiver (Assembly) consists of : 1

Receiver Box

Slide Button-Black (On/RS/Off)

L-Bracket (Floor Mount)

Wall Cover Plate-Black 1

Wall Cover Plate-White 1

Slide Button-White (On/RS/Off) 1

Screws (for Wall Cover Plate) 2

Plug-In Wiring Assembly – 18” Inches 1

Velcro (Loop and Hook) 1

Wall Anchor Screws 2

Wall Anchor 2

Installation Instructions

Screws (for fireplace system control covers)

Wall Bracket

FEATURES/SPECIFICATIONS

• Contemporary Ergonomic Table Top or Wall Mount Transmitter with Large LCD Display

• Battery Powered Transmitter and Receiver

• Easy Access Battery Door

• Pre-Programmed for Quick Installation

• Low battery Indication

• Child Proof Lock-out

• 16 Security Codes

• 2 hour Shut Down (Optional)

• Thermal Safety Shutdown (Transmitter Only)

• Quick Disconnect Wiring Assembly

• Reset Button

Summary of content (9 pages)

PAGE 1
TLM TOUCH LIGHT™ On/Off Remote Control INSTALLATION AND OPERATING INSTRUCTIONS This wireless wall on/off/ remote control – system provides a safe, reliable, and user-friendly remote control for millivolt valve gas appliances. The system can be manually turned on and off with the transmitter. Always check the appliance home owner’s manual for additional information, or warnings regarding accessory installation before connecting this remote control system. Carefully inspect the contents for shipping damage.
PAGE 2
WARNING Important Safety Information • • • • • NOTE Due to the sensitive temperature monitoring components in the transmitter, it is necessary to allow the transmitter to stabilize to room temperature before accurate room temperatures are displayed. If the transmitter is activated from a severe cold condition, allow 15 minutes for accurate temperature readings to appear on the LCD. WARNING Turn appliance OFF and allow to cool before installing or servicing.
PAGE 3
Remote Receiver: The remote receiver may be wall mounted or installed in the appliance per the appliance homeowner’s manual. Refer to the Homeowner’s Manual for special installation instructions. If wall mounted, the remote receiver must be installed in a junction box with cover plate provided. Failure to follow the installation instructions found in the appropriate Homeowner’s Manual will void the warranty and may cause a fire hazard.
PAGE 4
Installing Batteries: The Touch Light transmitter uses two (2) “AA”- size batteries. To install batteries, 1. Press down the battery door tab and lift up and remove the battery door. 2. Install the battery. 3. Close the battery door by snapping in place 4. Repeat the above step for the other battery. 5. When both batteries are installed, the transmitter will initialize for 10 seconds and then is ready for use. 6.
PAGE 5
1. The Touch Light transmitter comes preset from the factory with a 2 hour shutdown timer from its last ON operation. This is done to prevent the appliance from continuing to run if left unattended. 2. You may disable this feature if you wish. To disable, change the Touch Light transmitter privacy (DIP) 3. switch #1 ONLY to the OFF position (by sliding the switch towards the battery door.) Make sure the receiver privacy (DIP) switches are set the same.
PAGE 6
Transmitter: General: The TLM is a touch sensitive On/Off remote control system. The transmitter will operate the remote receiver from 1foot to a maximum of 20 feet. The operational range is reduced when batteries are low or when the receiver is inside a metal enclosure. Initial start up: 1. 2. 3. After initial power up or reset button is pressed, the transmitter is reset. During transmitter reset, all segments of the LCD will be turned on.
PAGE 7
1. 2. 3. Touch both sides of the groove surface with your two index fingers simultaneously for at least 3 seconds to enter child-proof mode. Once you hear two (2) beeps and the child proof icon appears on the LCD display, the child proof mode is activated. You will not able to turn the appliance on or off in this mode. Always place both fingers on the middle of the groove surfaces to ensure a proper touch. To deactivate child proof, repeat step 1.
PAGE 8
Low-battery detection: 1. 2. 3. Battery voltage is checked once a minute. When the battery voltage drops to a certain level, the low-battery warning will come on, and the transmitter will emit three (3) beeps and send signals to turn off the appliance. The transmitter will not function anymore until new batteries are installed. When the batteries are low, the LCD shows a blinking low battery indicator. Change the battery every six months before the battery is too weak for normal operation.
PAGE 9
TROUBLESHOOTING Symptom 1. LED light on receiver blinking or battery icon on LCD on transmitter. 2. LCD display is blank 3. LCD display shows “funny” display 4. Appliance does not come on after a valid touch (beep) Causes 1. Low Battery 1. Wiring / Electrical Connections 2. Privacy (DIP) switch setting on transmitter does not match receiver 3. Transmitter measures temperature exceeding 99 degrees Fahrenheit and shows “HI” on LCD 5. Receiver cannot receive signal. 4.