Quick Installation Guide IEEE 802.11n Wireless-N USB Dongle (Read Me First) Please install the driver before inserting the USB dongle WiFi Protected Setup (WPS) Pin-Code (Software WPS) or Push-Button Configuration Your other existing wireless peripherals must support WPS feature. After the driver has been installed, simply activate WPS feature on both devices to automatically configure the USB adapter wireless network security. See Page 6.
System Requirements USB 2.0 port (May not work on certain USB 1.1 port, and performance will be greatly reduced) Windows 2000, XP, or Vista operating system CD-ROM drive At least 100MB of available disk space Important Notice: If you want to use all the features provided by the wireless USB dongle or you are using Windows 2000, please install the “Install driver and AmbiCom Wireless Utility” or “Ralink Configuration Tool” during setup.
Driver Installation This guide will help you to install your USB dongle using the minimum set of parameters. For a detail description of the USB features, please refer to the digital manual on the CD. 1. Insert the Wireless Driver Setup CD into your CD-ROM drive. The setup should start automatically. Note: If the Setup screen does not start automatically: I.Click the Windows Start button, and then select Run. II.Browse to the CD-ROM drive and select “setup.exe” 2.
For all models: Windows 2000 operating system user should select “AmbiCom Wireless Utility” or “Ralink Configuration Tool”. Otherwise, see below: WL250N-USB WL300N-USB WL150N-nUSB WL150N-USBx Select “Install driver and Ralink WLAN Utility” for advance wireless features or “Microsoft Zero Configuration Tool” for simple wireless features. should select the “Ralink WLAN Tool” Select “Ralink Configuration Tool” for advance wireless features or “Microsoft Zero Configuration Tool” for simple wireless features.
8. If you have selected “Install driver only” option, doubleclick the wireless icon appear at the bottom right corner. If your wireless network has been setup with a wireless security code, you will need to type the code to gain access.
Wi-Fi Protected Setup (WPS) Pin-Code (Software WPS)/Push Button Configuration Depends on your model, the USB adapter support either PinCode WPS (software based WPS) or both Pin-Code and Push Button WPS features. WPS is a standard for easy and secure to add a new wireless device to your protected wireless home network without typing or configure complex wireless security setting with a compatible devices.
Technical Support Weekdays: 9:00a.m - 6:00p.m. (Monday – Friday. Except holidays) Phone: (408) 321 – 0822 Email: support@ambicom.com Website: www.ambicom.com Disclaimer This product is design for indoor use only. AmbiCom Inc., is not liable for the personal injury and property damage cause by misuse of this product. By using this product, users agree to obey their local regulations, public safety laws, and maintaining safety environment to other user.
USA/Canada During the warranty period, AmbiCom, Inc. will, at its option, either repair or replace defective products with similar parts and products. Should the product be identified as defective, the end user is responsible for returning the product to the place of purchase1 / manufacturer2 and the cost of shipping and handling. Any replaced or repaired product has a ninety-day (90-day) warranty or the remainder of the initial warranty period, whichever is longer.
Compatibility problems with any other software of hardware products. Installation of any other software of hardware products. Physical damage causes by misuse, misapplication or negligence. Warranty Limitations The warranty set forth above is exclusive and no other warranty, whether written or oral is expressed or implied. AmbiCom, Inc. specifically disclaims the implied warranties of merchantability and fitness for a particular purpose. AmbiCom, Inc.
Federal Communication Commission - Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C. The equipment version marketed in US is restricted to usage of the channels 1-11 only.
R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE) The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
