Amazfit Verge User Manual
Contents Watch Operating Instructions & Watch Status .............................................................................................. 3 1. Button Descriptions .................................................................................................................. 3 2. Touch Screen Gesture Operations ........................................................................................... 3 3. Off-Screen Mode ..........................................................................
Watch Operating Instructions & Watch Status 1. Button Descriptions Home Button Watch Status Button Functions Tapping Methods In standby Unlock the watch Short press Initiate the voice function from the watch face Short press Return to the watch face from other interface Short press Turn on the watch Press and hold for 2 seconds Turn off the watch Press and hold for 6 seconds After unlocking Others 2.
. Low-Light Mode In the low-light mode, only the time is displayed on the screen in the standby state (the pointer and the digital time are respectively displayed for the pointer watch face and the digital watch face). The entire watch face will not be displayed until you raise your wrist. When a message notification is received, the watch screen will light up to display the message content. Turning on the low-light mode will reduce the standby time on the watch.
6. System Status Symbol Once your watch is unlocked, the watch face will display system status symbols, each of which represents a different status. In the charging state. In a fully charged state. In a low-battery protection state. When the watch power is 5% or below, it will enter the low-battery protection mode. At this time, the watch must be charged more than 5% before exiting the protection mode. The watch is disconnected from the mobile phone.
Wearing the Watch & Charging Methods 1. Daily Wear To ensure that the optical heart-rate monitor detects the data properly, we recommend wearing the watch with two fingers’ width below your wrist bone, making sure it's fairly snug against your skin. 2. Wear during exercise When running or doing other activities, it is recommended that you wear your watch with a tight fit that is comfortable and does not slide up or down your wrist.
Use of Watch Functions 1. Watch Face Changing Watch Faces When the watch-face interface is pressed and held, the watch-face selection interface will appear, displaying the installed watch faces. You can also change the watch face in the "Amazfit Watch App" > "Profile/Me" > "My Watch" > "Select watch face" on your phone. 2. Widgets & Applications Applications refer to the specific function on the watch which can be used independently such as sleep, heart rate, compass, etc.
Starting an Activity After entering the preparation page for an outdoor activity such as running, the watch will automatically search for the GPS signal. Once the signal is obtained, tap GO to start running. After entering an indoor activity such as an elliptical trainer, tap GO to start the activity. About GPS Search When you enter the exercise preparation page for outdoor activities such as running, the watch will automatically start GPS positioning and alert you when positioning is successful.
Sports Setting Swipe up from the exercise preparation page to display "Sports Setting". Tap to adjust the settings of the running items as needed. i. Exercise Alert Setting the exercise alerts enables you to manage a variety of alerts, such as full-mile alerts, heart rate alerts, and more. It can be set as needed in the exercise settings. ii. Auto Lap You can set automatic lap miles in sports such as running, and you can turn on auto lap alerts.
iii. Pausing an Activity Press the physical button in the unlock state to pause an activity and press it once again to resume. Or slide to the leftmost interface, or tap the Pause button on the interface to control the activity. iv. Stopping an Activity After an activity is paused, select "Save" to end the activity. Select "Resume" to continue and select "Discard" to not to save the current activity.
Single Measurement Mode You can take a single heart-rate measurement when you need it. For more accurate heart-rate readings, please remain steady during the measurement. Continuous Heart Rate Mode After Continuous Heart Rate Mode is enabled, the Heart Rate app will display your heart rate per minute (bpm) as well as the average heart rate, maximum and minimum heart rate, and resting heart rate under the non-sports state during the day.
Playing Music on the Watch You can play audio directly on your watch. When playing with the watch, the music play symbol will be displayed on the watch face. Connecting to a Bluetooth Headset The watch supports Bluetooth headsets which include A2DP. You can select "Bluetooth " to scan the headsets in "Connection" in the "Settings" on the watch. When the connection is completed for the first time, the watch automatically connects to the headset each time the headset is turned on.
To check the sleep data: 1. You can tap the Sleep app on the watch to view; 2. Once the data is synchronized, you can view through Amazfit Watch App > Status > Sleep. 9. Bluetooth Phone Note: Currently the Bluetooth phone feature is only available for Android phones. The Bluetooth connection between the watch and the phone must be maintained when making a call so that the phone can send and receive calls normally.
10. Weather The Weather widget lets you check weather information in recent days at any time. Weather data must be synchronized over the cellular network, so keep your watch connected with your mobile phone to update the weather in a timely manner. 11. Alarms You can set up alarms on the watch. An alarm can be set to vibrate once or to repeat regularly. If you don’t need anymore the alarm you set up, you can remove it from the alarm list.
Watch Notifications 1. Message Notifications When the watch is connected to the phone, the message on the phone can be displayed on the watch. To enable app notifications: enable the specific notifications for Apps in "App Notification Settings" in "Profile" > "Settings" > "Notification Settings" from the Amazfit Watch app. Note: If you bind your Android mobile phone to your watch, please Amazfit Watch app and give it permission for auto-start.
2. Connecting with a Mac Your Mac computer needs to have the Android File Transfer tool installed in order for it to connect with your watch. After connecting the watch to the dock and then to the computer's USB port, the Android File Transfer tool will automatically pop up and display a list of files in the watch. 3. Copying Files When you access your watch through your computer, some folders will be displayed in the watch's root directory. You can copy the corresponding files into these folders.
