Installation Guide

ManualsBrandsAltronix ManualsElectronicsEoC Receiver and Transceiver Switch

eBridge4SK - 1 -

PLUS

eBridge100SPR - EoC Receiver

eBridge4SPT - 4 Port PoE/PoE+ EoC Transceiver Switch

Installation Guide

Rev. 072313

I.T.E. 43KC

Overview:

The eBridge4SK kit consists of eBridge100SPR and eBridge4SPT which are Coax to CAT-5 Ethernet adapters/media converters that deliver data and power over

coax cable. eBridge4SK enables fast 10/100 Base-T Ethernet digital communication. eBridge4SPT allows you to upgrade your existing infrastructure by replacing

a single analog device with up to four (4) PoE/PoE+ devices. eBridge100SPR passes data and sends power over the coax to the eBridge4SPT. Data transmission

and power over the Coax are possible up to 300m. Maximum range from head end to the PoE camera/device is 610m, taking into consideration that up to 100m

of structured cable may be deployed at each end. Built-in IP management allows for remote camera reset, monitoring and reporting via various IP protocols.

eBridge4SK enables cost-effective system upgrades and eliminates the costs and labor associated with installing new network cabling.

Note: Ethernet maximum distance (see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3).

Features:

*UL Listed Class 2 or limited power source (NetWay1D).

Agency Listings:

• UL/CUL Listed for Information

Technology Equipment (UL 60950-1).

• CE approved.

Input:

• eBridge100SPR - 51-56VDC/60W max. power.*

eBridge4SPT - powered by eBridge100SPR.

Power Output:

• eBridge4SPT: 4 ports PoE+ (30W) per port.

• Total output power: 60W.

Ethernet:

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair Cat-5e or better structured cable.

• Distance: up to 100m.

• Speed: 10/100BaseT, half/full duplex, auto negotiation.

Coax:

• Distance: up to 300m.

• Connectivity: BNC, RG-59/U or similar.

• Throughput is rated to pass 100mbps from camera to receiver.

With the proper headend equipment

multiple Megapixel cameras can be used.

LED Indicators:

• Blue LED - Coax link connection.

LED Indicators (cont’d):

• Green LED - Power (eBridge100SPR only).

• Yellow and Green LED (RJ45) IP Link status, 10/100Base-T/active.

Environmental:

• Operating Ambient Temperature :

eBridge100SPR: -40ºC to 60ºC (-40ºF to 140ºF).

eBridge4SPT: 60W: -40ºC to 75ºC (-40ºF to 167ºF).

• Storage Temperature: -40ºC to 75ºC (-40ºF to 167ºF).

• Humidity: 20 to 85%, non-condensing.

Applications:

• Retrofit digital IP cameras in an analog CCTV installation (up to four (4)

IP cameras expansion per analog camera).

• Works with Megapixel, HD720, HD1080 and VGA (SD) cameras

(see note, pg. 2).

• Extend Network link distance in an industrial environment.

• Upgrade deployed CCTV Coax to a digital network in Retail, Hospitality,

Arenas, Casinos, Airports, Schools, Hospitals, Transportation, etc.

Mechanical:

• Dimensions (H x W x D approx.):

eBridge100SPR: 4.375” x 3.5” x 1” (111.125mm x 88.89mm x 25.4mm)

eBridge4SPT: 1.7” x 5.23” x 8.93” (43.18mm x 132.84mm x 226.82mm)

Z1409

Summary of content (12 pages)

PAGE 1
Rev. 072313 Installation Guide PLUS eBridge100SPR - EoC Receiver eBridge4SPT - 4 Port PoE/PoE+ EoC Transceiver Switch Z1409 I.T.E. 43KC Overview: The eBridge4SK kit consists of eBridge100SPR and eBridge4SPT which are Coax to CAT-5 Ethernet adapters/media converters that deliver data and power over coax cable. eBridge4SK enables fast 10/100 Base-T Ethernet digital communication.
PAGE 2
Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for the application. eBridge100SPR and eBridge4SPT is not intended to be connected to outside plant leads and should be installed indoors within the protected premises. The eBridge100SPR and eBridge4SPT is intended for indoor use only. 1. eBridge100SPR installation: a.
PAGE 3
Fig. 1 Typical Application: eBridge100SPR eBridge4SPT (Front View) 56VDC Input Ethernet Switch Coax up to 300m PoE Output 10/100 Base-T CAT-5e up to 100m CAT-5e up to 100m NVR Network Video Server (Head End Equipment) CAT-5e up to 100m PoE/PoE+ Cameras PoE/PoE+ Cameras Maximum Length of Coax Type vs. Camera Power/PoE Class: Camera Power/ PoE Class 13W/0 or 13W/3 25W 60W RG59/U (23AWG) RG59/U (22AWG) 260.64m 118.9m 50.3m+ 335.28m 150.6m 63.4m+ RG59/U (20AWG) Max. Length (meters) 500m 239.
PAGE 4
3. Open a browser on the computer and enter “192.168.168.168” into the address bar. A dialog box Authentication Required will appear requesting both user name and password enter the default values here. Click on the button labeled Log In. 4. The status page of the eBridge4SPT will appear. This page displays the real time status and health of each device connected to the eBridge4SPT. Network Setup: Click on the tab labeled Network Settings. This will open the Network Setting screen.
PAGE 5
4. HTTP Port: Enter the HTTP port number assigned to the eBridge4SPT module by the network administrator to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and unsecure. Even though HTTP can be used for remote access it is recommended primarily for use with LAN connections. 5. HTTPS Port: Enter the HTTPS port number assigned to the eBridge4SPT module by the network administrator to allow remote access and monitoring. The default inbound port setting is 443.
PAGE 6
network administrator and repeat the email setup sets. After all fields have been programed click the button labeled Reboot Server. A dialog box will display “Please allow up to 30 sec. for server to reboot”. Click OK. All programmed information will be saved after the server has rebooted. Setup: Click on the tab labeled Setup. The eBridge4SPT setup page will open. In this screen the Site ID, Date/Time and Port identification are setup, along with the ability to enable and disable individual ports.
PAGE 7
Man Security Settings: Status Setup Network Settings Security Settings Click on the tab labeled Security Settings. The eBridge4SPT security setting page will open. In this screen the SSL certificate and Key will be entered, the SSL can be enabled or disabled and new username and password can be set. Using an SSL certificate will ensure that when remotely accessing the eBridge4SPT all eBridge4SPT data has been encrypted and there for secure through the assigned HTPPS Port. Site ID: RJ Sports Wear Fig.
PAGE 8
Locality: Brooklyn SSL State: Organization: RJ Sports Wear Inc. Change Username and Password (Fig. 4c, pg. 8): Unit Name: eBridge4SPT 1. Username: Enter the new Username (up to 32 characters) required to access the eBridge4SPT. 2. Password: Enter the new Password (up to 32 alpha numeric required to access Common Name: characters) 192.168.168.168 the eBridge4SPT. Email Address: mike@rjsports.com 3. Confirm Password: Reenter the new Password. Click the button labeled Save Username and Password.
PAGE 9
Heartbeat Timer: The heartbeat timer will send a trap message indicating that the eBridge4SPT is still connected and communicating. Setting the Heart Beat Timer: 1. Click the button labeled Heartbeat Timer Setting. 2. Select the desired time between heartbeat messaging in the Days, Hours, Minutes and Seconds in corresponding fields. 3. Click the button labeled Submit to save settings. Fig. 6 Management Interface Status Setup Network Settings Security Settings v1.99.
PAGE 10
Status Screen: a. Class Power (Watts) (Fig. 7a, pg. 10): Wattage required by the PoE class of the device. b. Actual Power Draw (Watts) (Fig. 7b, pg. 10): Amount of watts being drawn by the connected device. c. Device Status (Fig. 7c, pg. 10): Active or Inactive. d. Port Status (Fig. 7d, pg. 10): Indicates whether port is Enabled or Disabled. Fig. 7 WEBVIEW INTERFACE Management Interface Status Setup Network Settings Security Settings Site ID v1.99.22 Events Log eBridge4SPT Status Wednesday, Jul.
PAGE 11
Notes: eBridge4SK - 11 -
PAGE 12
PoE Output 10/100 Base-T 5.23” (132.84mm) Coax SLOC link LED 1.7” (43.18mm) 8.93” (226.82mm) Fig. 8 8.42” (213.87mm) eBridge4SPT Chassis Mechanical Drawing & Dimensions (H x W x D approx.): 1.7” x 5.23” x 8.93” (43.18mm x 132.84mm x 226.82mm) Shelf Installation A 1- Position and affix rubber pads (C) (included) at each corner on the bottom of the unit (Fig. 9). 2- Place unit in desired location. Fig.