Data Sheet
AL600ULACMCBJ converts a 115VAC 60Hz input Into eight (8) independently con-
trolled 12VDC or 24VDC Fail-Safe and/or Fail-Secure outputs with a total of 6 amp
continuous supply current. Outputs are activated by an open collector sink or normally
open (NO) dry trigger input from an Access Control System, Card Reader, Keypad,
Push Button, PIR, etc. This unit will route power to a variety of access control hard-
ware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. The
outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is designed
to be powered by one common power source (factory installed) which will provide
power for both the board operation and locking devices, or two (2) totally independent
power sources, one (1) providing power for board operation and the other for lock/
accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring,
or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is
individually selectable for any or all of the eight (8) outputs.
AL600ULACMCBJ
Power Supply/Chargers with Multi-Output
Access Power Controllers Rev. DSAL600ULACMCBJ_05182015
Overview
Specifications
AL600ULACMCBJ
Input:
• Input 115VAC 60Hz rated @ 3.5 amp.
• Power supply input options:
a) One (1) common power input for ACM8CB and
lock power (factory installed).
b) Two (2) isolated power inputs - One (1) to power
the ACM8CB and one (1) for lock accessory
power (external power supply is required). Current
is determined by the power supply connected, not
to exceed a maximum of 10 amp total.
• Eight (8) Access Control System trigger inputs.
Input options:
a) Eight (8) normally open (NO) inputs.
b) Eight (8) open collector inputs.
c) Any combination of the above.
Output:
• 12VDC or 24VDC @ 6 amp supply current.
• Class 2 Rated power-limited outputs.
• Eight (8) independently controlled outputs.
Output options:
a) Eight (8) Fail-Safe and/or Fail-Secure power outputs.
b) Eight (8) form “C” 5 amp rated relay outputs
c) Any combination of the above.
• Eight (8) auxiliary power outputs (unswitched)
• Output ratings:
- PTCs are rated @ 2.5 amp.
• Filtered and electronically regulated outputs
(built-in power supply).
Supervision:
• AC fail supervision (form “C” contacts).
- Notification trigger is selectable for
30 seconds (factory set) or 6 hours.
• Low battery and battery presence supervision
(form “C” contact).
Features:
• Fire Alarm disconnect (latching or non-latching) is
individually selectable for any or all of the
eight (8) outputs.
• Fire Alarm disconnect input options:
a) Normally open (NO) or normally closed (NC)
dry contact input.
b) Polarity reversal input from FACP signaling circuit.
• Alarm output relay indicates that FACP input is
triggered (form “C” contact rated @ 1 amp 28VDC
not evaluated by UL).
• Short circuit and thermal overload protection.
Visual Indicators:
• Red LEDs indicate outputs are triggered
(relays energized).
• Green LED indicates FACP disconnect is triggered.
• AC input and DC output LED indicators.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Power Supply Board maximum charge current 0.7 amp.
• Automatic switch over to stand-by battery when AC fails.
• Zero voltage drop when unit switches over to battery
backup (AC failure condition).
Electrical:
• Operating temperature: 0º C to 49º C ambient.
• ACM8CB board main fuse is rated at 10 amp.
• BTU/Hr.:
- 12VDC: 36.85 BTU/Hr.
- 24VDC: 73.70 BTU/Hr.
Mechanical:
• Enclosure Dimensions (H x W x D approx.):
18” x 14.5” x 4.625” (457.2mm x 368.3mm x 117.48mm).
• Enclosure accommodates up to two (2) 18AH batteries.
• Product weight (approx.): 14.85 lbs. (6.74 kg).
• Shipping weight (approx.): 17.1 lbs. (7.76 kg).