Data Sheet

ManualsBrandsAltronix ManualsElectronics5 PTC Access Control Power Supply Charger, 12VDC

Input:

• Input 115VAC, 60Hz, 2.6 amp.

• Input fuse rated @ 3.5 amp/250V.

• Fire Alarm Panel or Access Control System trigger

inputs. N.O. or N.C. supervised trigger input and

polarity reversal trigger input.

Output:

• 12VDC outputs.

• 10 amp supply current.

• Five (5) PTC protected Class 2 Rated power-limited

outputs, rated @ 2 amp.

• Output relay energizes when unit is triggered

(form “C” contact rated 1 amp @ 28VDC).

• Filtered and electronically regulated output.

• Short circuit and thermal overload protection.

Battery Backup:

• Built-in charger for sealed lead acid or

gel type batteries.

• Automatic switch over to stand-by battery

when AC fails.

• Maximum charge current 0.7 amp.

Supervision:

• AC fail supervision (form “C” contacts).

- Notification trigger is selectable for

30 seconds (factory set) or 6 hours.

• Low battery supervision (form “C” contacts).

• Battery presence supervision (form “C” contacts).

• Power fail supervision relay (form “C” contacts).

Visual Indicators:

• AC input and DC output LED indicators

(power supply board).

• Red LEDs indicate condition of power outputs

(multi-output board).

• Power and input trigger LEDs (multi-output board).

Electrical:

• Operating temperature: 0º C to 49º C ambient.

• 61.42 BTU/Hr.

• System AC input VA requirement: 299VA.

Mechanical:

• Enclosure Dimensions (H x W x D approx.):

15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)

- Accommodates up to two (2) 12VDC/12AH batteries.

• Product weight (approx.): 8.95 lbs. (4.06 kg).

• Shipping weight (approx.): 10.25 lbs. (4.65 kg).

Specifications

AL1012ULM

Multi-Output Power Supply/Charger

Rev. DSAL1012ULM_05212015

AL1012ULM multi-output access control power supply/charger is specifically

designed for use with access control systems and accessories. This unit converts

a 115VAC, 60Hz input into five (5) individually PTC protected Class 2 Rated

power-limited 12VDC outputs. Each output will route power to a variety of ac-

cess control hardware devices including Mag Locks, Electric Strikes, Magnetic

Door Holders, etc. These outputs will operate in both Fail-Safe and Fail-Secure

modes. Controlled trigger input is achieved through normally open (N.O.) or

normally closed (N.C.) supervised input or the polarity reversal from an FACP

(Fire Alarm Control Panel). A form “C” dry output relay enables HVAC Shut-

down, Elevator Recall or it may be used to trigger auxiliary devices.

Overview

Agency Approvals

UL 294 UL Listed for Access Control

System Units.

CUL Listed - CSA Standard C22.2

No.205-M1983, Signal Equipment.

AL1012ULM

Summary of content (2 pages)

PAGE 1
AL1012ULM Multi-Output Power Supply/Charger Rev. DSAL1012ULM_05212015 Overview AL1012ULM AL1012ULM multi-output access control power supply/charger is specifically designed for use with access control systems and accessories. This unit converts a 115VAC, 60Hz input into five (5) individually PTC protected Class 2 Rated power-limited 12VDC outputs. Each output will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc.
PAGE 2
Enclosure Dimensions (H x W x D approximate): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.8mm) 5.0” (127.0mm) 5.0” (127.0mm) 1.1” (27.94mm) 1.25” (31.