User's Manual MX-30 3-CHANNEL DJ MIXER R LTO www.altoproaudio.com Version 1.
the recommended fuse type as indicated in this manual. Do not short-circuit the fuse holder. Before replacing the fuse, make sure that the product is OFF and disconnected from the AC outlet. SAFETY RELATED SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Protective Ground This symbol, wherever used, alerts you to the presence of un-insulated and dangerous voltages within the product enclosure. These are voltages that may be sufficient to constitute the risk of electric shock or death.
PREFACE Dear Customer: Thank you for choosing the eavours. For the LTO MX-30 3-Channel DJ Mixer, which is the result of our LTO AUDIO TEAM's end- LTO AUDIO TEAM, music and audio are more than a profession, it is a passion and an obsession! We have, in fact, been designing professional audio products for a number of years in cooperation with many of the world's major brands. The LTO line represents unparalleled analogue and digital products made by musicians, for musicians.
TABLE OF CONTENTS 1. INTRODUCTION.....................................................................................................................................4 2. FEATURE LIST.......................................................................................................................................4 3. CONTROL ELEMENTS..........................................................................................................................5 3.1 The Top Cover 3.1.1 CHANNEL Section 3.1.
1. INTRODUCTION What a great DJ mixer you have just bought. Your MX-30 is packed with features such as 3 turntable inputs 3 line inputs, 1 microphone input, 3 bands equalizer and gain control for per channel etc.. Through your MX-30 is very easy to operate, for getting the best out of your MX-30, please go through this manual carefully. 2.
3. CONTROL ELEMENTS 3.
3.1.1 The CHANNEL Section CHANNEL 1 -. MIC to PHONO-LINE Switch 1 The channel 1 is equipped with the MIC to PHONO-LINE switch. This switch is used to select microphone input and phono/line Input. When it is in the right position, you can use the PHONO/LINE switch on the rear panel to input the line signal to the phono input connector. 1 PHONO LINE MIC 3 MIN GAIN MAX 4 -30dB +15dB -30dB +15dB -30dB +15dB TREBLE -.
3.1.2 The MAIN OUT Section 9 -. OUT A Control The OUT A control is used to adjust the main level of the AMP output on rear panel. MAIN OUT 9 MIN OUT A -. BAL A Control 10 The BAL A control is used to adjust the stereo balance of the AMP output on rear panel. MAX 10 LEFT BAL A RIGHT 11 -. OUT B Control 11 The OUT B control is used to adjust the main level of the BOOTH output on rear panel. OUT B 12 OFF -.
3.1.5 The CROSSFADER Section -. FADER Control 18 CH 2 Through this crossfader you can fade in between channel 2 and channel 3. The crossfader on your MX-30 is user replaceable. CH 3 18 3.2 The Front Panel REVERSE HOLD SMOOTH MIC IN PHONE OUT 19 20 REVERSE TAP 21 SHARP CROSSFADER CURVE 22 3.2.1 MIC IN Jack 19 This input will accept any unbalanced low impedance microphone. The functions of the microphone will be controlled by the CHANNEL section on the top cover. 3.2.
3.3 The Rear Panel 26 24 25 28 27 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: SHOCK HAZARD - DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR POWER MODEL Apparaten skall anslutas till jordat uttag nar den ansluts till ett natverk ON AMP OFF BOOTH SERIAL GND GND SEND TAPE FROM PFL RETURN TO MAIN LINE PHONO LINE PHONO GND LINE PHONO L Use only with a 250V fuse R AC INPUT MAIN OUT 23 USA / Canada 100-120V 60Hz Fuse:T500mAL UK / Aust 240V 50Hz Fuse:T315mAL 3.
3.3.5 EFFECTS Send and Return You can send the PFL signal through the SEND 29 sockets to a signal processor such as reverb, equaliser, etc.. Then from the same effect unit you bring the signal back into the MX-30 via the RETURN 30 sockets and the audio signal is routed into the MAIN output. 3.3.6 INPUT - PHONO input 31 : The three Channels feature PHONO inputs including RIIA preamplifier for turntable. PIN (RCA) jacks shall be used to connect the turntable.
4. TECHNICAL SPECIFICATIONS INPUTS Phono Inputs 1,2 and 3 40dB gain@1kHz,unbalanced Line Inputs 1,2 and 3 0dB gain, unbalanced Mic Input 40dB gain, servo-balanced Return 0dB gain, unbalanced Headphones typically 125mW@ 1% THD Main Out max +21dBu Booth Out max +21dBu Tape Out typically 0dBu Send typically 0dBu Stereo Bass +15dB/ 30dB@ 50Hz Stereo Middle +15dB/ 30dB@2.
A B C D 1 PHONO LINE PHONO LINE P B A 6 5 4 3 2 1 R L R L R L 2 CHANNEL 3(INPUT) PHONO LINE CHANNEL 2(INPUT) PHONO LINE PHONO LINE PHONO LINE PHONO LINE PHONO LINE PHONO LINE PHONO LINE 3 P B A P B A P B A LEVEL METER 5 4 6 6 3 2 5 4 3 2 1 4 6 1 5 6 3 2 1 4 5 6 3 2 1 5 4 3 2 1 6 5 4 3 2 1 4 P D C P D C P D C 4 PHONE / LINE B A PHONE / LINE B A B A P 12 P CHANNEL 1(INPUT) PHONO LINE P 3 P P 2 P 1 12 11
6. WARRANTY 1. WARRANTY REGISTRATION CARD To obtain Warranty Service, the buyer should first fill out and return the enclosed Warranty Registration Card within 10 days of the Purchase Date. All the information presented in this Warranty Registration Card gives the manufacturer a better understanding of the sales status, so as to purport a more effective and efficient after-sales warranty service.
SEIKAKU TECHNICAL GROUP LIMITED No. 1, Lane 17, Sec. 2, Han Shi W. Road, Taichung, 401 Taiwan http://www.altomobile.com Tel: 886-4-22313737 email: info@altomobile.com Fax: 886-4-22346757 All rights reserved to ALTO Mobile. Due to continued development in response to customer feedback, product features, specifications and/or internal/external design may be changed without prior notice. No photocopying, translation or reproduction of any part of this user manual is allowed without prior written permission.
