User's Manual

ManualsBrandsAltenergy Power System ManualsElectronicsZigbee module

昱能科技

NO.1 Yatai Road, Jiaxing, Zhejiang, China

浙江省嘉兴市南湖区亚太路 1 号

+86 57383986967 | APsystems.com

User Manual for APS2530H

The model used ZigBee PRO protocol to send RF signals for device communication.

The model can be used after pairing with a dedicated device which was installed with a

receiver dongle.

APS2530H was used as a dongle which need to be installed in customer’s device. It

offers UART to communicate with customer’s device according predefined protocol.

1:product figure(APS2530H)

2: Technical specifications

RF operating frequency: 2402MHz ~ 2483MHz

Reference frequency: 2.400GHz

Channel spacing: 5MHz

Channel wide：2MHz

Modulation method: OQPSK

Communication rate: 250Kbps

Summary of content (6 pages)

PAGE 1
User Manual for APS2530H The model used ZigBee PRO protocol to send RF signals for device communication. The model can be used after pairing with a dedicated device which was installed with a receiver dongle. APS2530H was used as a dongle which need to be installed in customer’s device. It offers UART to communicate with customer’s device according predefined protocol. 1:product figure(APS2530H) 2: Technical specifications RF operating frequency: 2402MHz ~ 2483MHz Reference frequency: 2.
PAGE 2
Output power: 15DBm Communication mechanism: applied ZigBee frequency hopping mechanism, passively frequency hopping. Average operating current：<20mA Operating voltage：2V-3.6V Max remitting current: 20mA Max rate：250Kbit/s Receiving sensitivity： -95dbm Receiving current：<24mA Max receiving distance：>100M Normal operating receiving distance： 100M 昱能科技 NO.1 Yatai Road, Jiaxing, Zhejiang, China 浙江省嘉兴市南湖区亚太路 1 号 +86 57383986967 | APsystems.
PAGE 3
. Installation and usage instructions Installation Notes: users can use SMT or DIP to connect to ZIGBEE module. It must be ensured that the interface of the module(VCC,GND,RESET,UART) is accurately connected with the customer's equipment. Make sure the IPEX interface is properly connected to the antenna. Instructions for use: Users can interact with the zigbee module through the serial port.
PAGE 4
P0_7 P1_0 P1_1 P1_2 P1_3 P1_4 P1_5 P1_6 P1_7 P2_0 P2_1 P2_2 VCC GND RESET_N Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Power Ground Digital input Port0.7 Port1.0 – 20-mA drive capability Port1.1 – 20-mA drive capability Port1.2 Port1.3 Port1.4 Port1.5 Port1.6 Port1.7 Port2.0 Port2.1 Port2.2 2-V–3.6-V digital power-supply connection Connect to GND Reset, active-low Package Size 4.
PAGE 5
- - - control Unit or any of its components. EF Radiation Exposure and Hazard Statement: To ensure compliance with FCC RF exposure requirement, this device must be installed in a location such that antenna of the device will b greater than 20cm away from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to installation instructions provided in this manual.
PAGE 6
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF exposure warning This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d’exposition aux radiations de la IC définies pour un environnement non contrôlé.