Quick Setup Guide Altai CX200 Outdoor 2x2 8 0 2 . 1 1 a c W a v e 2 AP _________________________________________________ Quick Setup Guide Version 1.1 1 Altai Technologies Ltd.
Quick Setup Guide Introduction Thank you for purchasing the Altai CX200 product. This guide provides instructions to install the product and set it up as AP with minimal effort. Package Contents Detachable Antennae - 2.4GHz Antenna x 2 CX200 Main Unit Pole Mount Hose Clamp - 5GHz Antenna x2 Wall Mount Kit - Anchors - Screws Quick Setup Guide Adhesive Label x2 x2 PoE Injector (Optional) 2 Altai Technologies Ltd.
Quick Setup Guide Hardware Overview LED Indicator LED Indicator Power Off AP powered off Flashing Red AP booting up Solid Red AP boot up finished and ready for service LAN (Ethernet) Off LAN disconnected Solid Green LAN connected Flashing Green Data Transmitting/Receiving 2.4 GHz/5G WiFi Off Radio Disabled Radios Solid Green 1. AP mode on but with no client (AP/Station/ association; OR Repeater/Bridge) 2. Station mode on but not connected to remote AP; OR 3.
Quick Setup Guide Ethernet Port and RF Antenna Port 5GHz Dipole 2.4GHz Dipole Antenna Antenna NOTE: To ensure correct antenna connection, check the labels (2.4GHz/5GHz) printed on each antenna body and RF port for easy reference. 5GHz Dipole Antenna 2.4GHz Dipole Antenna Ethernet Port Ethernet Port: Used to connect to power source (see the Power Options in the later section) and provides 10/100/1000 Mbps network interface for LAN connection. RF Antenna Ports: Used to attach 2.
Quick Setup Guide Setup Preparation Wire stripping tool and crimping tool Screwdriver (Slot type and Phillips type) Drill and drill bits Computer with Web Browser: Google Chrome, Mozilla Firefox, or Microsoft Internet Explorer 8 (or above) Two Cat 5e/6 Ethernet cables 802.3af-compliant PoE switch AltaiCare account (Optional) for cloud AP management and user service Ethernet Cable Feed-Through Seal the RJ45 cable Connector with the provided cable gland.
Quick Setup Guide Mounting Options Option 1: Pole Mount (For 1.5 to 2.5 inches of pole diameter) 1 Thread the open end of the hose clamp through the two slots of the mount base. 2 Determine where the AP is to be placed. Tighten the hose clamp to secure the base to the pole. 1 2 6 Altai Technologies Ltd.
Quick Setup Guide Option 2: Wall Mount 1 Determine where the AP is to be placed and use the adhesive label to mark location of the two mounting holes on the wall surface. 2 Use an appropriate drill bit to drill two holes, each with 1/3” (8.1mm) in diameter and 1” (26mm) deep, on the markings. 3 Remove the label. Drive the anchors into the holes and then the screws into the anchors. 4 Align the mounting slots with the screw heads and attach the AP to the wall in place.
Quick Setup Guide Power Options and Cable Connection Instructions You can follow one of the options below for CX200 configuration as described in the following sections. Option 1: 802.3at-Compliant PoE switch 1. Connect the CX200 Ethernet port to an 802.3af-compliant PoE switch with an Ethernet Cable. 2. Connect a computer to the switch. 3. Make sure the Power LED turns into 802.3af – Compliant PoE Switch a solid light for AP configuration. Option 2: PoE Injector (Purchased separately) 1.
Quick Setup Guide 1. Change TCP/IP Setting on Your Computer For Windows 7/8/10 users, 1. Go to Control Panel, click Network and Sharing Center and then choose the adapter that you want to connect to CX200 unit. In this example, adapter “Local Area Connection” is in connection with CX200. Click it and then click Properties. 2. Under the Networking tab, click Internet Protocol Version 4 (TCP/IPv4) in the list box “This connection uses the following items”, and then click Properties. 3.
Quick Setup Guide 2. Access to Web Interface 1. Open a web browser. Type 192.168.1.222 in the address bar and then hit Enter. 2. Login page will come up and you are required to enter username and password. By default, the credentials are: Username: admin Password: admin 3. Click Login. 10 Altai Technologies Ltd.
Quick Setup Guide 3. Configure AP Mode (2.4G/5G) Network Scenario ISP Modem Gateway/Router CX200 (AP Mode) 2.4G + 5G Coverage Internet Modem Ethernet Ethernet Cable Cable Cable Go to Configuration > Wireless > Radio0(2.4G)/Radio1(5G) > General. Below screenshots show an example for 2.4G radio configuration only. Same procedures can be applied to 5G radio configuration. 1. Make sure the box of Enable Radio is checked. Select AP mode for the field of Radio Mode. Then click Submit. 2.
Quick Setup Guide 3. Make sure WLAN is enabled by checking the box. Type in SSID to name the wireless network you want to broadcast and then click Submit. 4. Click the tab WLAN Security. Select WPA2-PSK from the drop down menu of Authentication Mode and select AES for Cipher Mode. Type in a password within 8~64 characters or numbers in Pass Phrase and click Submit. 5. Click Save & Apply at the top right corner to have all changes take effect. 6. Hook up the CX200 as shown in Network Scenario.
Quick Setup Guide 4. Connect with Cloud-Based Controller – AltaiCare Network Scenario: ISP Modem CX200_1 (AP) Local Gateway/ Router CX200_2 (AP) 1. You can manage your CX200 and set up hotspot service for the subscribers with AltaiCare, which is a cloud-based system. 2. Go to Configuration > Network > General. Select Switch Mode for Network Setting and make sure the CX200 can reach Internet and communicate with AltaiCare by inputting valid IP settings either via DHCP or with Static IP configuration.
Quick Setup Guide 3. Click Remote Mgmt and check the box of Enable Remote Management. Select AltaiCare as Management Type and Cloud as Connection Type. 4. Select Full Management if the device is running in AP Mode. For Station Mode, Bridge Mode and Repeater Mode, select Monitor Mode instead. 5. Click Submit and then Save & Apply at the top right corner to make all the changes take effect. 6.
Quick Setup Guide Federal Communication Commission Interference Statement (FCC) – USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Quick Setup Guide Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3.
Quick Setup Guide Warning Only use the power adaptor supplied with CX200. Using a different power adaptor might damage the device. Disclaimer All specifications are subject to change without prior notice. Altai Technologies assumes no responsibilities for any inaccuracies in this document or for any obligation to update information in this document. This document is provided for information purposes only.
