C2s Dual-band 2x2 802.11ac WiFi AP/Bridge Model: C2-2221-000 Installation Guide Version 1.0 Date: May, 2016 Altai Technologies Ltd.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide Copyright © 2016 Altai Technologies Limited ALL RIGHTS RESERVED. Altai Technologies Limited Unit 209, 2/F, Lakeside 2, 10 Science Park West Avenue, Hong Kong Science Park, Shatin, New Territories, Hong Kong Telephone: +852 3758 6000 Fax: +852 2607 4021 Web: www.altaitechnologies.com Customer Support Centre: Email: support@altaitechnologies.com ii Altai Technologies Ltd.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide Radio Frequency Interference Requirements This device complies with Part 15 of FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. 3. This device should not be co-located or operating in conjunction with any other antenna or transmitter.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide . C2s access points require professional installation. Please install a lightning arrestor to protect the access point for lightning dissipation during rainstorms. Lightning arrestors are mounted outside the structure and must be grounded by means of a ground wire to the nearest ground rod or item that is grounded. Disclaimer All specifications are subject to change without prior notice.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide Table of contents TABLE OF CONTENTS ...................................................................................................................... V 1. INTRODUCTION ......................................................................................................................1 2. FIELD INSTALLATION...............................................................................................................2 2.1.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 1. Introduction This guide is designed to provide the information needed to mount Altai C2s Super WiFi AP/CPE at the site location. The document is applicable for hardware platform C2s and the following models. Product name: C2s Dual-band 2x2 802.11ac WiFi AP/Bridge It is assumed in this document that a site survey has been performed before the site installation. The appropriate antenna pole and AP locations have been selected.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 2. Field Installation 2.1. Unpack the shipment Check the equipment and the installation kits against the packing list to ensure that the equipment part numbers, parts, and the ancillary equipment included in the shipment match what is specified on the packing list. The shipment consists of a C2s Super WiFi AP/CPE and an installation kit in the container.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 2.2. Hardware Overview LED Panel 2.4G/5G Radio WiFi (AP/STA/Repeater/Bridge Mode) Solid Green: 1. AP Mode on but with no Clients Associated 2. STA/Repeater Mode on but not connected to AP 3.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide Ethernet Reset Reset Button Eth. Port 1 Ports and Button Eth. Port 0 ETH0/PoE IN: It is used to connect to power source (see the Power Options in the following section) and provides 10/100/1000 Mbps network interface for LAN connection. ETH1: It provides 10/100/1000 Mbps network interface for LAN connection with peripherals.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 2.3. Preparation for Installing C2s Before installation, please prepare the following tools: 1) Needle-Nose Pliers (for cable feed-through) 2) Screw Driver (for wall mount) 3) RJ45 Shielded Connector Crimper 4) STP CAT5e/6 Straight Cable x 2 5) Waterproof Sealing Tapes and Electrical Tapes 6) Grounding Cable 7) An 802.3at to Passive PoE Adapter (Optional and ordered separately when using with 802.3at-compliant PoE switch or PoE injector) 2.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 2.5. Mounting Options Option 1: Pole Mount 1. Orient the device to point to the target coverage area (for AP mode) or to the target AP (for Station mode). 2. Loop two cable ties through the slots on the back of the device and then wrap them around the pole. 3. Tighten the cable ties to ensure the device is firmly in place. Option 2: Wall Mount 60mm 1.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 2.6. Power Options and Cable Connection Instructions Option 1: AC Adapter and DC Injector 1. Connect C2s ETH0 port to a DC injector’s “PWR+DATA” port with an Ethernet Cable. 2. Connect a computer to the DC injector’s “DATA” port with another Ethernet Cable. 3. Connect the AC power adapter to the DC injector and plug it into a power socket. 4. Make sure the Power LED light is yellow and ETH 0 LED light is blue/green. Option 2: 802.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 2. Connect a port of an 802.3at PoE Switch to the PoE Adapter “802.3at” port with another Ethernet Cable. 3. Make sure the Power LED light is yellow and the ETH0 LED light is blue/green. 4. Connect a computer to the switch. 8 Altai Technologies Ltd.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 2.7. C2s Waterproof Protection Especially for outdoor installation, waterproof protection can enhance the protection from water Ingress. Both the LAN cable and the unit should be wrapped. 1. Wrap the cable with a layer of rubber tape. Start from 5cm below the connector. Wrap a loop and overlap a half. Continue until it reaches under the connector. 2. Wrap the C2s unit with a layer of rubber tape. Start from 1cm above of the lid.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 3. Wrap the C2s unit with a layer of electrical tape. Start from 1cm above the rubber tape wrapping. Wrap a loop and overlap a half. Continue until it reaches the bottom. 10 Altai Technologies Ltd.
Altai C2s Dual-Band 2x2 802.11ac WiFi AP/CPE Installation Guide 3. Electrical Protection 3.1. Surge Protector It is strongly advised the C2s unit be installed with surge protector (ordered separately), especially for outdoor deployment, to protect it against electrical surge. The surge protector should be grounded properly and installed as close to the C2s unit as possible in order to prevent the C2s from the electrical damage. 3.2.
