User's Manual

ManualsBrandsAlps Electric ManualsElectronicsBLUETOOTH(TM) Module

DSGD.

CHKD.

APPD.

TITLE

HARDWARE

SPECIFICATION

SYMB. DATA OR NO. APPD. CHKD. DSGD.

Proprietary Information Confidential page 31

5.Aug.2013 / UGZZF-2 Specification Rev.0.0.1

UGZZF-2

9. REGIONAL REGULATIONS

This Product has taken the following regulatory modular approval by the antenna described in the chapter

9.1, 9.2, 9.3 and 9.4.

a) Japanese Radio Law Certification [Japan]

Article 2-1of the Certification Ordinance 19

b) FCC and IC Certification [North America and Canada]

FCC Part15 SubpartC

RSS-210

c) R&TTE Directive Certification [EU]

EN 300 328 V1.8.1

EN 301 489-1 V1.9.2

EN 301 489-17 V2.2.1

EN62479:2010

EN60950-1:2006+A11:2009+A1:2010+A12:2011

Customer can certify their product without RF test for regulatory RF certification, if following conditionsare satisfied.

Otherwise additional RF certifications are necessary.

1) Antenna type (shape, size, etc.) shall be similar with the tested antenna by ALPS.

2) Antenna gain shall be lower than the tested antenna by ALPS.

3) EMC performance shall satisfy the condition of each certification.

These requirements shall be guaranteed by the customer.

FCC requirements:

 If the FCC ID written in the label which is stuck on the surface of the device can not seen from out side

when it’s installed in a customer’s product, following indication is necessary to be showed on the

product in which the device is installed. And the indication is also necessary to be written in a user

manual of the customer’s product.

“Contains Transmitter Module FCC ID: CWTUGZZF2”, or

“Contains FCC ID: CWTUGZZF2“

 FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

 Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

 This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

Summary of content (2 pages)

PAGE 1
Proprietary Information Confidential page 31 9. REGIONAL REGULATIONS This Product has taken the following regulatory modular approval by the antenna described in the chapter 9.1, 9.2, 9.3 and 9.4. a) Japanese Radio Law Certification [Japan] Article 2-1of the Certification Ordinance 19 b) FCC and IC Certification [North America and Canada] FCC Part15 SubpartC RSS-210 c) R&TTE Directive Certification [EU] EN 300 328 V1.8.1 EN 301 489-1 V1.9.2 EN 301 489-17 V2.2.
PAGE 2
Proprietary Information Confidential page 32 IC requirements:  If the IC Number written in the label which is stuck on the surface of the device can not seen from out side when it’s installed in a customer’s product, following indication is necessary to be showed on the product in which the device is installed. And the indication is also necessary to be written in a user manual of the customer’s product.