Installation Manual

ManualsBrandsAlps Electric ManualsElectronicsBluetooth Module

      ALPS Bluetooth

Module UGPZ6 specification Ver. 1.0

June 7, 2005

page1

User Guide Information to 2.4GHz ALPS Bluetooth

Module

Model UGPZ6

Caution: This user guide information is only provided to OEM or module installer.

Do not supply to the end user.

1. Introduction:

The ALPS, UGPZ6 with Bluetooth

wireless technology is a radio device that transmits and receives

radio signals in accordance with the spectrum regulations for the 2.4 GHz unlicensed frequency range.

The following table shows a major function.

Model

No.

Major Function Remarks

UGPZ6

1. Output Power; Bluetooth™ class 2. 2.5mW (+4dBm) Max.

2. External 4 different antennas connected via antenna connector.

3. Voltage regulator built in. Rating of Input voltage: +3.3Vdc, +/-0.2V

4. Flash memory (8M bytes) built in

5. Reference oscillator built in

6. Board to board connection through USB interfaces, V2.0

7.Operating temperature: Nominal; +15 °C to +35 °C

8. Regulatory frequency range

USA, Canada, Europe, Taiwan, Korea, China and Japan: 2400 – 2483.5MHz

There kinds of

External

antenna

 



Electrical features Contents

Program memory 8M bits (256k bytes x 32 bits) Flash memory

RAM 32k bytes x 16 bits

Reference oscillator Built in

Sub clock oscillator Built in

USB interface USB (V2.0) : OHCI and UHCI)



2. Radio part

Bluetooth™ Transceiver Module, model UGPZ6 has fully integrated 2.4GHz radio transceiver with Class2 power,

receiver and frequency-hopping synthesizer.

Then, UGPZ6 has also provision of Adaptive Frequency Hopping (AFH) that is used to improve the performance

of physical links in the presence of interference as well as reducing the interference caused by physical links on

other devices in the ISM band. AFH shall only be used during the connection state.

In order to facilitate power management, each section of the radio may be powered up and down separately.

Various software controllable switches have been implemented to control power to the transmitter, the frequency

synthesizer/VCO, the receiver and the LNA, if provided.

Summary of content (6 pages)

PAGE 1
ALPS BluetoothTM Module UGPZ6 specification Ver. 1.0 June 7, 2005 User Guide Information to 2.4GHz ALPS BluetoothTM Module Model UGPZ6 Caution: This user guide information is only provided to OEM or module installer. Do not supply to the end user. 1. Introduction: The ALPS, UGPZ6 with BluetoothTM wireless technology is a radio device that transmits and receives radio signals in accordance with the spectrum regulations for the 2.4 GHz unlicensed frequency range. The following table shows a major function.
PAGE 2
ALPS BluetoothTM Module UGPZ6 specification Ver. 1.0 June 7, 2005 3. Base band part Bluetooth™ Module contains link controller, which performs all the real-time functions of the Bluetooth™ baseband protocol layer, including data transfer and connection management. The device also controls states of operation enables sniff, park and hold modes of operation. Real-time functions such as frequency-hopping burst timing and clock synchronization are also implemented in this hardware.
PAGE 3
ALPS BluetoothTM Module UGPZ6 specification Ver. 1.0 June 7, 2005 (3) Markings To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter Module FCC ID: CWTUGPZ6 Any similar wording that expresses the same meaning may be used. (4) Caution to user for modification The following caution is expressed on the user’s instruction manual.
PAGE 4
ALPS BluetoothTM Module UGPZ6 specification Ver. 1.0 June 7, 2005 (3) Markings To satisfy Industry Canada exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter Module IC: 1788F-UGPZ6 Any similar wording that expresses the same meaning may be used. 4.3 Europe The UGPZ6 module with CE marking will assist our customer into advance.
PAGE 5
ALPS BluetoothTM Module UGPZ6 specification Ver. 1.0 June 7, 2005 (2) The outer cabinet of the end product shall be fixed by easily access method, such fixing with plus / minus screws to open the outer cabinet by general public. The permanently fixing method, such using security screws are not allowed for mounting method. The labeling to exterior of the end product has a meaning of “Contains transmitter device certified under Japanese radio law ”, or similar wording.
PAGE 6
ALPS BluetoothTM Module UGPZ6 specification Ver. 1.0 June 7, 2005 (4) Markings on end product The following markings are marked on the end product and its package. The user manual describes the meaning of the markings. If there is no spacing on the end product, the sticker is used as an alternate. ２．４ＦＨx 1) “ 2.4 “ means radio operated in 2.4 GHz bands. 2) “ FH “ means modulating type, FH-SS.