Installation Manual

ManualsBrandsAlpine ManualsAudio7" Multimedia Receiver For The 2007-2018 Jeep Wrangler

Jeep Wrangler

i407-WRA-JK 20210811v1

 1/18

Jeep Wrangler

i407-WRA-JK

Restyle Installation Manual

 Model: Wrangler JK

 Model Year: 2007-2018

Note:

Design and speciﬁcations are subject to change without notice for improvement.

To Ensure Safe Use, Always Follow These Precautions

The installation of this product requires specialized skills and experience. We recommend that you have the

product installed by an Alpine authorized dealer.

Before you use this product, be sure to carefully read this installation manual and the separate user's manual

so that you can use the product correctly. Alpine Electronics bears no responsibility for problems that arise as

a result of failure to follow the instructions in the manuals.

This manual includes a number of symbols that are intended to help you use the product safely, to prevent

harm to you and others, and to protect against damage to property. These symbols and their meanings are

listed below. Make sure you fully understand these symbols before you begin reading the main text.

Explanations of Injury and Damage That May Result from Incorrect Use

Warning

Ignoring the content marked by this indication and using the product incorrectly is

expected to lead to death or serious injury.

Caution

Ignoring the content marked by this indication and using the product incorrectly is only

expected to lead to injury or property damage.

Jeep

Model Year

Wrangler JK 2007-2018

* The speciﬁed vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is

not guaranteed if the manufacturer has made production changes to the listed vehicles above.

Warning: Before you begin wiring, remove the ground wire from the negative

terminal of the battery. Failing to do so can lead to electric shock, injury or damage

to equipment.

Introduction

Congratulations on purchasing the i407-WRA-JK. This installation manual is designed to take you through the

step-by-step installation of the i407-WRA-JK into a 2007-2018 Jeep Wrangler JK. Please familiarize yourself

with the owners manual and if you still have additional questions please call 1-800-TECH-101.

Summary of content (18 pages)

PAGE 1
Jeep Wrangler i407-WRA-JK 20210811v1 1/18 Jeep Wrangler i407-WRA-JK Restyle Installation Manual Model: Wrangler JK Model Year: 2007-2018 Jeep Model Year Wrangler JK 2007-2018 * The speciﬁed vehicles have been tested and have met compatibility specs at the time of testing. Compatibility is not guaranteed if the manufacturer has made production changes to the listed vehicles above. Warning: Before you begin wiring, remove the ground wire from the negative terminal of the battery.
PAGE 2
Jeep Wrangler i407-WRA-JK Types of Precautions Forbidden Forbidden Mandatory Indicates that disassembly is forbidden. Indicates actions that are mandatory (must be performed) Marks content that should receive your full attention. Warning Forbidden Store screws and other small objects where children cannot reach them. If one of thse small objects is swallowed, consult with a doctor immediately. Mandatory Before you begin wiring, remove the ground wire from the negative terminal of the battery.
PAGE 3
Jeep Wrangler i407-WRA-JK 20210811v1 3/18 Tools Required Panel Removing Tool 7mm Sockets #2 Phillips Screwdriver Wire Cutters Extension Ratchet T20 Torx Digital Multimeter Air Saw Wire Strippers Pliers
PAGE 4
Jeep Wrangler i407-WRA-JK 20210811v1 4/18 Accessory List Head Unit Box Parts (i407-WRA) iLX-407 Head Unit Round Head Screws M5#8 (4pcs) Video In/Out Harness Camera/Preout Harness Side Mounting Brackets L&R Documents OM QR Card Alpine Registration Card Aux Power Pig Tail USB Angled Extension Cable Installation Manual Hands Free Microphone iDatalink Maestro Box Parts (ALP-MRR4/ALP-HRN-WRA4) Maestro Flashing Cable USB Micro To Full Size Main Harness FM/AM Antenna Adapter iDatalink Maestro Mod
PAGE 5
Jeep Wrangler i407-WRA-JK 20210811v1 5/18 Programming the iDatalink Maestro Module 1 INSTALL THE WEBLINK PLUG-IN Go to: idatalinkmaestro.com/plugin and follow the installation steps. The Maestro module must be programmed specifically for each vehicle and radio. Take care to enter the correct vehicle information, factory options, head unit model, and head unit serial number.
PAGE 6
Jeep Wrangler i407-WRA-JK 20210811v1 6/18 Factory Unit Disassembly Process (2007-2010 Only) 1 DISCONNECT THE BATTERY BEFORE CONTINUING. FAILURE TO DO SO WILL DISABLE MANY FEATURES. Remove top by releasing 2 rear clips on the back of the top panel and then pull panel forward. 3 Release 2 clips on the top of the bottom panel. This will expose two 7mm screws. Remove using a 7mm socket with ratchet & extension. 5 Extract (4) 7 mm screws and remove the factory radio.
PAGE 7
Jeep Wrangler i407-WRA-JK 20210811v1 7/18 Factory Unit Disassembly Process (2011-2017 Only) 1 DISCONNECT THE BATTERY BEFORE CONTINUING. FAILURE TO DO SO WILL DISABLE MANY FEATURES. Remove the rubber cover from the top center storage area and extract (1) 7mm screw. 2 Remove the knee cover panel and extract (2) 7mm screws located to the right and left sides of the steering wheel column. Left side of steering wheel column. Right side of steering wheel column.
PAGE 8
Jeep Wrangler i407-WRA-JK 20210811v1 8/18 Installation Instructions 1 Plug the OBDII connector on to the OBDII port below the driver side dash and run the extension to the radio cavity. 2 Attach the side brackets using the provided 8mm round head screws. 3 Mount the microphone as illustrated and run the cable to the radio cavity. You will need to use a T20 Torx to remove the visor. For optimal performance it should be mounted by the rear-view mirror as illustrated.
PAGE 9
Jeep Wrangler i407-WRA-JK 20210811v1 9/18 Disconnecting the Uconnect® (only for 2011-2017 vehicles with factory Uconnect®) 1 3 2 Remove the factory climate control panel. It is clipped on and can be removed with a panel removing tool. Extract the (2) 7mm bolts from Uconnect® module. Disconnect the 24pin OEM connector. NOTE: Since the factory Uconnect® system is not going to be used you can unplug the 24 pin connector shown in step 2.
PAGE 10
Jeep Wrangler i407-WRA-JK 20210811v1 10/18 i407-WRA-JK Wiring Diagram AMPLIFIED VEHICLES To Vehicle Connectors WARNING! Failure to follow this procedure will result in no audio from Navigation and Bluetooth sources.
PAGE 11
Jeep Wrangler i407-WRA-JK 20210811v1 11/18 Component Locations IMPORTANT: These would be the typical locations used to install the separate components. The Maestro module and SiriusXM tuner (sold separately) would not have restrictions and could be moved based on the installers discretion.
PAGE 12
Jeep Wrangler i407-WRA-JK i407-WRA-JK HDMI Usage With An iPhone For all phones the USB power source needs to be a 2A source. This will require a separate USB power source to be installed in the vehicle. For all phones the USB power source needs to be a 2A source. This will require a separate USB ANTENNA power source to be installed in the vehicle. Do not use the head unit’s USB to power HDMI devices. This port is meant for Apple CarPlay, Android Auto, and USB flash drives.
PAGE 13
Jeep Wrangler i407-WRA-JK 20210811v1 13/18 i407-WRA-JK Wire Descriptions Vehicle Antenna CAN Interface Connector (included) USB extension cable (included) To Interface Box To USB flash drive, iPhone or Android smartphone Microphone (included) VIDEO IN VIDEO OUT VIDEO IN/OUT cable REMO (Blue/White) To drive recorder, DVD player, etc. To Rear monitor To amplifier or equalizer REVERSE (Orange/White) To plus side of the back lamp signal lead of the car P.
PAGE 14
Jeep Wrangler i407-WRA-JK 20210811v1 14/18 Wire Harness Pin Outs Radio I/O Radio Main 8 16 7 15 6 14 5 13 4 12 3 11 2 10 1 9 Blue 22AWG Red 20AWG Blue/White 22AWG Orange/White 22AWG Yellow/Blue 22AWG Purple 20AWG Gray 20AWG Purple/Black 20AWG Gray/Black 20AWG Green 20AWG White 20AWG Green/Black 20AWG White/Black 20AWG Yellow 18AWG Black 18AWG 18 16 14 12 10 8 6 4 2 Yellow/Black 22AWG Red/Brown 22AWG Yellow/Brown 22AWG 5 6 3 4 1 2 Black 22AWG Yellow/Black 22AWG Red 22AWG Orange/White 22AWG Orange
PAGE 15
Jeep Wrangler i407-WRA-JK 20210811v1 15/18 Connection Of HCE-TCAM1-WRA (Optional Rear Camera) iLX-407 Source Unit Main Harness VIDEO IN/OUT USB HDMI IN CAN I/F ANTENNA Rear View Camera 6-pin Black Connector Rear View Camera MIC SWC CAMERA/PRE OUT SXM/DAB POWER WARNING! The use of this connection This connection goes to is intended for Alpine the camera connector on HCE-TCAM1-WRA rear the main harness. This view camera ONLY.
PAGE 16
Jeep Wrangler i407-WRA-JK 20210811v1 16/18 Adding The KTA-450 (Sold Separately) (2011-2017 Only) To make room for the KTA-450 the tabs on the OEM rear support bracket need to be bent outward about 1/2” as shown in the pictures below. This will help support the rear and amplifier. A protective tape or heat shrink needs to be used so the metal does not cause damage to the amplifier. The push nut from the OEM rear support bracket will also need to be removed.
PAGE 17
Jeep Wrangler i407-WRA-JK 20210811v1 17/18 Set Up Guide 1 2 3 Turn the vehicle’s Ignition switch to ACC. 4 If a rear camera is present, turn it ON in the settings menu. (HOME/SETTINGS/CAMERA/REAR CAMERA/ CAMERA SELECT/REAR/OK). 5 If a front camera is present, turn it ON in the settings menu. (HOME/SETTINGS/CAMERA/FRONT CAMERA/ CAMERA SELECT/FRONT/OK). 6 If the AUX Input is being use be sure to turn it ON in the settings. (HOME/SETTINGS/GENERAL/AUX/AUX SELECT).
PAGE 18
Jeep Wrangler i407-WRA-JK 20210811v1 18/18 Troubleshooting Guide Continued Symptom Possible Cause Remedy One of the power wires does not have proper voltage Test the power wires with a digital multimeter and trace from there. 4 pin Maestro data cable is disconnected or damaged. Check for proper connection or disconnected pins. OBD2 cable is not plugged in. Connect OBD2 connector to the OBD2 port. Main harness is not connected. Check for proper connection or disconnected pins.