UB YST-SW216 Subwoofer System OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
FCC INFORMATION (for US customers) We Want You Listening For A Lifetime 1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used.
Thank you for selecting this YAMAHA subwoofer system. CAUTION: Read this before operating your unit Please read the following operating precautions before use. YAMAHA will not be held responsible for any damage and/or injury caused by not following the cautions below. • To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
SPECIAL INSTRUCTIONS FOR U.K. MODEL IMPORTANT: THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
PLACEMENT One subwoofer will have a good effect on your audio system, however, the use of two subwoofers is recommended to obtain more effect. A If using one subwoofer, it is recommended to place it on the outside of either the right or the left front speaker. (See fig. A .) If using two subwoofers, it is recommended to place them on the outside of each front speaker. (See fig. B .) The placement shown in fig.
CONNECTIONS Choose one of the following two connecting methods that is more suitable for your audio system. ■ Choose 1 (pages 3-4) when you want to enjoy 5.1 surround system ■ Choose 2 (pages 5-6) when you want to output the low frequency signals Caution Unplug the subwoofer and other audio/video components before making connections. Notes • All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”.
CONNECTIONS ■ Using one subwoofer Subwoofer OUTPUT TO SPEAKERS INPUT 2 OUTPUT TO SPEAKERS HIGH CUT /MONO VOLUME INPUT 2 Mono pin cable (not included) HIGH CUT HIGH LOW INPUT 1 FROM AMPLIFIER Audio pin cable (not included) /MONO POWER ON OFF HIGH LOW INPUT 1 FROM AMPLIFIER To AC outlet Amplifier ■ Using two subwoofers Mono pin cable (not included) OUTPUT TO SPEAKERS INPUT 2 HIGH CUT OUTPUT TO SPEAKERS /MONO INPUT 2 HIGH CUT /MONO HIGH LOW HIGH LOW INPUT 1 FROM AMPLIFIER INPUT
CONNECTIONS Connecting to speaker output terminals of the amplifier 2 Select this method if your amplifier has no line output (pin jack) terminal. If your amplifier has two sets of front speaker output terminals and both terminals can output sound signals simultaneously. • Connect one set of front speaker output terminals of the amplifier to the INPUT 1 terminals of the subwoofer, and connect the other set of front speaker output terminals of the amplifier to the front speakers.
CONNECTIONS If your amplifier has only one set of front speaker output terminals. Connect the speaker output terminals of the amplifier to the INPUT 1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the front speakers.
CONNECTIONS Connecting to the INPUT 1/OUTPUT terminals of the subwoofer For connection, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from the subwoofer or the speakers, or both of them. Make sure that the + and – polarity markings of the speaker cables are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass.
CONTROLS AND THEIR FUNCTIONS Subwoofer rear panel OUTPUT TO SPEAKERS INPUT 2 2 OUTPUT TO SPEAKERS HIGH CUT /MONO 34 INPUT 2 HIGH CUT VOLUME HIGH LOW INPUT 1 FROM AMPLIFIER /MONO 1 POWER ON VOLUME OFF HIGH LOW INPUT 1 FROM AMPLIFIER 7 1 POWER switch Press this switch to the ON position to turn on the power to the subwoofer. When the power of the subwoofer is on, the power indicator (4) on the rear panel light up in green.
ADJUSTING THE SUBWOOFER BEFORE USE Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and the front speakers by following the procedures described below. Subwoofer rear panel OUTPUT TO SPEAKERS INPUT 2 1,6 OUTPUT TO SPEAKERS HIGH CUT /MONO INPUT 2 HIGH CUT VOLUME HIGH LOW INPUT 1 FROM AMPLIFIER /MONO 3 POWER ON VOLUME OFF HIGH LOW INPUT 1 FROM AMPLIFIER 5 1 2 3 Set the VOLUME control to minimum (0).
ADJUSTING THE SUBWOOFER BEFORE USE Frequency response The frequency response of this subwoofer dB 90 HIGH CUT HIGH 80 70 60 HIGH CUT LOW 50 40 20 50 100 200 500Hz The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer is combined with a typical front speaker system. ■ EX.1 When combined with a 4” or 6.
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY II In 1988, Yamaha brought to the marketplace speaker systems utilizing YST (Yamaha Active Servo Technology) to give powerful, high quality bass reproduction. This technique uses a direct connection between the amplifier and speaker, allowing accurate signal transmission and precise speaker control.
TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center. Problem Cause What to Do Power is not supplied even though the POWER switch is set to the ON position. The power plug is not securely connected. Connect it securely. No sound. The volume is set to minimum. Raise the volume up.
SPECIFICATIONS Type .....Advanced Yamaha Active Servo Technology II Power Consumption .............................................. 45 W Driver........................................25 cm (10”) cone woofer Magnetic shielding type Dimensions (W x H x D) ...................................... 340 mm x 340 mm x 385 mm (13-3/8” x 13-3/8” x 15-5/32”) Output Power .............. 50 W (100 Hz, 5 Ω 10 %T.H.D) Dynamic Power ............................................ 100 W, 5 Ω Input Impedance ...............
© 2006 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND SCANDINAVIA A.