Product User Manual For Wireless Mini-PCI (Ralink Solution) Model Number: WMP-N07-5365A1 ALPHA Proprietary and Confidential Information
Revision History Rev. Date Author Reason for Changes 1.
Contents 1.0 SCOPE.............................................................................................................................................5 1.1 DOCUMENT ....................................................................................................................................5 1.2 PRODUCT FEATURES .......................................................................................................................5 2.0 REQUIREMENTS..............................................
1.0 Scope 1.1 Document This document is to specify the product requirements for Wireless Mini-PCI. This Mini-PCI Card is based on Ralink RT2800 chipset that complied with 802.11n draft 1.0 standard from 2.4~2.5GHz, and it can be used to provide up to 11Mbps for IEEE 802.11b and 54Mbps for 2.4GHz IEEE 802.11g to connect your wireless LAN. With seamless roaming, fully interoperability and advanced security with WEP standard, Wireless Mini-PCI offers absolute interoperability with different vendors’ 802.
2.2 General Requirements 2.2.1 IEEE 802.11b Section # Feature Detailed Description 2.2.1.1 2.2.1.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers y y IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK y 2400 ~ 2497MHz ISM band y Data Rate Media Access Protocol Transmitter Output Power Receiver Sensitivity y y 11 channels for United States 13 channels for Europe Countries 13 channels for Japan 11, 5.5, 2, and 1Mbps CSMA/CA with ACK y 23.
# Feature Detailed Description 2.2.2.3 2.2.2.4 Operating Frequency Channel Numbers y y 2.2.2.5 2.2.2.6 Data Rate Media Access Protocol Transmitter Output Power Receiver Sensitivity y y 2.2.2.7 2.2.1.8 y y y y y y y y y y y 2400 ~ 2483.5MHz ISM band 11 channels for United States 13 channels for Europe Countries 13 channels for Japan From MCS – 0 to MCS –15 as shown in Appendix A CSMA/CA with ACK HT20: 20.68dBm HT40: 20.
2.3 Software Requirements The Configuration Software supports Microsoft Windows 98SE, ME, 2000, and XP. This configuration software includes the following functions: y Information Information allows you to monitor network status. y Configuration Configuration allows you to configure parameters for wireless networking. y Security Supports enhanced security WEP, 802.1x,WPA. 2.3.1 Information # Feature Detailed Description 2.3.1.1 General Information y 2.3.1.2 Current Link Information y 2.3.1.
# Feature Detailed Description 2.3.3.2 WEP Management y y 2.3.3.3 2.3.3.4 802.1x WPA y y y y Four WEP keys can be selected STA with WEP off will never associate any AP with WEP enabled WEP Key Format: Option for Hex format Support EAP-TLS, EAP-TTLS, and EAP-PEAP Support WPA-PSK and WPA-EAP Support Cipher Mode AES and TKIP 2.4 Mechanical Requirements # Feature Detailed Description 2.4.1 2.4.2 2.4.3 Length Width Height y y y 50.8mm 59.59mm 0.99mm 2.
FCC statement in User's Manual (for class B) "Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules.
This exterior label can use wording such as the following: “Contains Transmitter Module NCC ID: Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.