Installation Guide For WMP-D16 IEEE 802.
以下警語適用於台灣地區: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法 規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用 電波輻射性電機設備之干擾。 本模組於取得認證後將依規定於模組本體標示審驗合格標籤，並要求平台上標示 「本產品內含射頻模組：ID 編號」 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example: Access point, Wireless Router, Notebook, etc.).
Industry Canada Statement Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 5 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
Test Utility Installation: 1. Unzip “ART_V52_build58.zip” to “C:\”. 2. The utility must run on Win2000 or WinXP. Hardware Installation: Before insert the adapter , please execute the below instruction at first !! 1. Win2000 OS : Enter in the directory : C:\ ART_V52_build58\art_driver\bin\2000 Execute the inst_new_drv_2k.bat : WinXP OS : Enter in the directory : C:\ ART_V52_build58\ art_driver\bin\XP\ Execute the inst_new_drv_xp.bat 2.
2. Input the instruction : art \id=2062 Then press enter . ART TEST MODE: 1. Once utility is executed, a menu with test options will appear. To run a test, press the character key that is assigned to the test option. For example, press “c” to run the continuous transmit test, or press “r ” to run the continuous receive test. For example: press “o” to change 11g or 11b test mode, Press “c” to continuous transmit mode . 2. Continuous Transmit Options.
3. Continuous Receive Options Continuous receive options will put the radio into receive mode to allow for radio measurements. Press ESC to return to the main Test Options menu when finished. 1.0 Scope 1.1 Document This document is to specify the product requirements for IEEE 802.11a/b/g MiniPCI Card. This Mini-PCI Card is based on Atheros AR5413 chipset .. With seamless roaming, fully interoperability and advanced security with WEP standard, IEEE 802.
1.2 Product Features Ÿ Compatible with IEEE 802.11a/b/g standard to provide wireless 54Mbps data rate.
2.2 General Requirements 2.2.1 IEEE 802.11a Section # Feature Detailed Description 2.2.1.1 2.2.1.
# Feature Detailed Description 2.2.2.5 2.2.2.6 Data Rate Media Access Protocol Ÿ Ÿ 13 channels for Europe Countries 14 channels for Japan 11, 5.5, 2, and 1Mbps CSMA/CA with ACK 2.2.2.7 Transmitter Output Power Ÿ Typical 18dBm at 11, 5.5, 2, and 1Mbps 2.2.2.8 (Average power) Receiver Ÿ Sensitivity Ÿ Typical –84dBm for 11Mbps @ 8% PER Typical –90dBm for 2Mbps @ 8% PER 2.2.3 IEEE 802.11g Section # Feature Detailed Description 2.2.3.1 2.2.3.
2.2.4 General Section # Feature Detailed Description 2.2.3.1 Antenna Connector Operating Voltage Current Consumption Ÿ Dual UFL antenna connectors Ÿ 3.3VDC +/- 10% Ÿ Ÿ Ÿ Ÿ 520mA at continuous transmit mode 260mA at continuous receive mode 15mA at sleep mode Mini-PCI Type IIIB form factor Ÿ External LED function supported 2.2.3.2 2.2.3.3 2.2.3.4 2.2.3.
2.3 Software Requirements The Configuration Software supports Microsoft Windows 98SE, ME, 2000, and XP. This configuration software includes the following functions: Ÿ Information Information allows you to monitor network status. Ÿ Configuration Configuration allows you to configure parameters for wireless networking. Ÿ Security Supports enhanced security WEP, 802.1x,WPA,WPA2. 2.3.1 Information # Feature Detailed Description 2.3.1.1 General Information Ÿ 2.3.1.2 Current Link Information Ÿ 2.3.1.
# Feature Detailed Description 2.3.2.4 RTS Threshold Ÿ 2.3.2.5 Fragment Threshold Transmission Speed Ÿ Roaming Ÿ 2.3.2.6 2.3.2.7 Ÿ Set the number of bytes used for fragmentation boundary for messages Set the number of bytes used for RTS/CTS boundary This indicates the communication rates. Select appropriate transmission speed to match your wireless LAN settings Support Automatic or Manual Rescan to associate with access point. 2.3.3 Security # Feature Detailed Description 2.3.3.
# Feature Detailed Description and Functionality Report 2.6 Requirements of Reliability, Maintainability and Quality # Feature Detailed Description 2.6.1 2.6.2 MTBF Maintainability Ÿ Ÿ 2.6.3 Quality Ÿ Mean Time Between Failure > 30,000 hours There is no scheduled preventive maintenance required The product quality is followed-up by ALPHA factory quality control system 2.7 Environmental Requirements # Feature Detailed Description 2.7.
檔名: 目錄: 舊資料 範本: WMP-D16 Manual (updated) S:\客服部\明泰\960316H01 WMP-D16 (註 Version 1)\ C:\Documents and Settings\sam\Application Data\Microsoft\Templates\Normal.
