User’s Manual For WUS-G09V WUGC-100 Model Number: WUS-G09V, WUGC-100 Revision: 1.0 This document contains confidential proprietary information and is the property of Alpha Networks Inc.. The contents of this document may not be disclosed to unauthorized persons without the written consent of Alpha Networks Inc..
Contents 1.0 SCOPE ..................................................................................................................................................................1 1.1 DOCUMENT ..........................................................................................................................................................1 1.2 PRODUCT FEATURES ...........................................................................................................................................
1.0 Scope 1.1 Document This document is to specify the product requirements for 802.11g USB module. This USB module is based on Conexant chipset that complied with IEEE 802.11b and 802.11g standards from 2.4~2.5GHz, and it can be used to provide up to 11Mbps for IEEE 802.11b and 54Mbps to connect your wireless LAN. With seamless roaming, fully interoperability and advanced security with WEP standard, 802.11g USB module offers absolute interoperability with different vendors’ 802.
2.2 General Requirements 2.2.1 IEEE 802.11b Section # Feature Detailed Description 2.2.1.2 2.2.1.2 Standard Radio and Modulation Schemes Operating Frequency Channel Numbers Ÿ Ÿ IEEE 802.11b DQPSK, DBPSK, DSSS, and CCK Ÿ 2400 ~ 2497MHz ISM band Ÿ Data Rate Media Access Protocol Transmitter Output Power Receiver Sensitivity Ÿ Ÿ 11 channels for United States 13 channels for Europe Countries 14 channels for Japan 11, 5.5, 2, and 1Mbps CSMA/CA with ACK 2.2.1.3 2.2.1.4 2.2.1.5 2.2.1.6 2.2.1.7 2.2.1.
2.2.3 General Section # Feature Detailed Description 2.2.3.1 2.2.3.2 2.2.3.3 Antenna Type Operating Voltage Power Consumption Form Factor and Interface LEDs Ÿ Ÿ Ÿ Ÿ Ÿ Two IPEX connector for external antenna 5VDC +/- 5% 400 mA at transmit mode 250 mA at receive mode with receiving packet High Speed USB2.0 Interface Ÿ Ÿ Act. LED Link LED 2.2.3.4 2.2.3.5 Blink: Transmit data On: Link with Access Point 2.
# Feature Detailed Description 2.3.2.6 Roaming Ÿ # Feature Detailed Description 2.3.3.1 Encryption Ÿ Ÿ Ÿ 2.3.3.2 WEP Management Ÿ Ÿ 2.3.3.3 2.3.3.4 802.1x WPA Ÿ Ÿ Ÿ Ÿ wireless LAN settings Support Automatic or Manual Rescan to associate with access point. 2.3.
# Feature conditions Non-Operating Humidity Conditions 2.8.4 l Detailed Description Ÿ range of 20% and 80% non-condensing. The product is not damaged nor the performance is degraded after exposure to relative humidity ranging from 5% to 95% non-condensing Environmental factors may affect actual range U.S.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.