Service Manual

ManualsBrandsAlliance Laundry Systems ManualsElectronicsWireless Network Control

WARNING

This kit is to be installed in accordance with the

manufacturer’s instructions and all codes and re-

quirements of the authority having jurisdiction. In

Canada, this conversion/installation shall be carried

out in accordance with the requirements of the pro-

vincial authorities having jurisdiction and in accord-

ance with the requirements of the CAN/CGA-B149.1

and CAN/CGA-B149.2 installation code. Failure to

follow instructions could result in serious injury,

death or property damage. The qualified agency per-

forming this work assumes all responsibility for this

kit installation.

W013R4

Kit consists of:

203532 Wireless Networ Contk rol

1 F8674006 Wireless Network Harness

2 D503661 Screws

2 55881 Wire Ties

1 XXXXXX Conversion Label

1 F8673901 Network Option Diagram

1 XXXXXX Wireless Control Label

1 8-18-253EN Kit Instructions

Important Instructions

Subject: Wireless Network Control

Ratings: 12VDC

Equipment Radio Type IEEE 802.15.4 Radio

Frequency Band 2.4GHz ISM Band

Frequency of Operation 2405 – 2475 MHz

IMPORTANT: This kit must be installed by a qualified

service person.

NOTE: Refer to appropriate service manual to aid in the

installation of this kit.

IMPORTANT: When reference is made to directions

(right or left) in this instructions, it is from operator's

position facing front of machine.

FCC COMPLIANCE STATEMENT

CAUTION

Changes or modifications not expressly approved

could void your authority to use this equipment .

This device complies with Part 15 of the FCC Rules. Operation to

the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interfer-

DO NOT COPY or TRANSMIT

1 Form No. 8-18-253EN

October 2018

Magnetic 5/16 in. Socket

Special Tools required for this kit:

WARNING

To reduce the risk of electric shock, fire, explosion,

serious injury or death:

• Disconnect electric power to the machine before

servicing.

• Close gas shut-off valve to the machine before

servicing.

• Close steam gate valve to the machine before

servicing.

• Never start the machine with any guards/panels

removed.

• Whenever ground wires are removed during serv-

icing, these ground wires must be reconnected to

ensure that the machine is properly grounded.

W017

Summary of content (11 pages)

PAGE 1
Important Instructions Subject: Wireless Network Control Ratings: 12VDC Equipment Radio Type IEEE 802.15.4 Radio Frequency Band 2.4GHz ISM Band Frequency of Operation 2405 – 2475 MHz WARNING Kit consists of: This kit is to be installed in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction.
PAGE 2
IMPORTANT: Be careful not to damage control panel overlay when prying up tabs. ence received, including interference that may cause undesired operation. INDUSTRY CANADA STATEMENT Topload Washer Illustrated This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 3
. Use a flat blade screwdriver and slightly bend each tab up only far enough to allow getting the jaws of a pliers under each tab and bend to 90 degrees. Make sure each tab is bent up square and straight. © Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 3 Form No.
PAGE 4
7. Install F8674006 Wireless Network Harness between network board "H3" and the electronic control "H1". Refer to Figure 4. 8. Secure the F8674006 Wireless Network Harness using the (2) 55881 Wire Ties as shown in Figure 4 . 9. Place F8673901 Network Option Diagram in control cabinet with existing diagrams. 10. Place XXXXXX Wireless Control Label in the control hood be-hind the control panel. 11. Fill out and place XXXXXX Conversion Label in control hood behind control panel. 12.
PAGE 5
Front Control Washer Illustrated 1 1. IMPORTANT - Disconnect electrical power to machine. Control will not recognize network board until power is cycled to machine. 2 2. Open access panel to gain access to the control area. Refer to Service Manual. 3. Adjust the compliance jumpers on the 203532 Wireless Network Control. Refer to Compliance Jumper (H1) section at the end of these instructions. 4.
PAGE 6
D503661 Screw. Refer to Figure 8 . Repeat for installing second network board. Washer Illustrated 2 1 3 1 2 4 FLW227K 1. Electronic Control 2. "H1" 3. F8674006 Wireless Network Harness 3 SWD273K_SVG 1. 203532 Wireless Network Control 2. Slot 3. D503661 Screws Figure 7 7. Place F8673901 Network Option Diagram in control cabinet with existing diagrams. 8. Place XXXXXX Wireless Control Label in control cabinet be-hind control panel. Figure 8 6.
PAGE 7
11. Reconnect electrical power to the machine. 7. Add one 55881 Wire Tie to backside of electronic control as shown in Figure 10 . 8. Place F8673901 Wiring Diagram in control cabinet with existing diagrams. 9. Place XXXXXX Wireless Control Label in the control cabinet. NOTE: The machine control MUST have been powered down prior to connecting the wireless control assembly in order for the control to recognize the board and to allow communication with it.
PAGE 8
at a reduced power-level, which will reduce the performance of the Wireless Network Control. NOTE: It is the responsibility of the installer to make sure that the Compliance Jumper is set to meet local standards. Incorrect settings will cause the board to be out of compliance and may lead to reduced range and loss of WiFi channels. Figure 11 © Copyright, Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 8 Form No.
PAGE 9
Federal Communications Commission (FCC) Interference Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE.
PAGE 10
Device Classifications Since host devices vary widely with design features and configurations module integrators shall follow the guidelines below regarding device classification and simultaneous transmission, and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities.
PAGE 11
Simultaneous Transmission Evaluation This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications).