RM5 Manual This Manual covers the RM5 Module Version 1.
Allflex RM5 Manual TABLE OF CONTENTS I. Regularity Notices and Conformity .........................................................................................................................................3 II. Label Instructions .....................................................................................................................................................................5 III. Product Safety Notices ...........................................................................
Allflex RM5 Manual I. REGULARITY NOTICES AND CONFORMITY Australia and New Zealand RMA This device has been tested and meets the Electromagnetic Compatibility requirements for CISPR 32 and Radio testing AS/AZS 4268 This device meets Electromagnetic Radiation Human Exposure Standard 2003 for EME -Meets Category A under the Compliance Labelling Notice 2014 USA – FCC Information to the user (FCC Part 15.
Allflex RM5 Manual IC Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Allflex RM5 Manual II. LABEL INSTRUCTIONS The outside of final products that contain a RM5 device must display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: NQY-RM5 IC: 4246A-RM5 Any similar wording that expresses the same meaning may be used. III. PRODUCT SAFETY NOTICES The system must be installed in plastic enclosure compliant with UL94-V0 or in metallic enclosure.
Allflex RM5 Manual 1.0 RM5 OPERATING DESCRIPTION The RM5 is a standalone near field 12VDC RFID reader, design to read ISO11784/5 compliant passive tags. The module consists of an ARM based microcontroller clocked by 17.1776MHz VCXO. An internal PLL generates a 60MHz internal clock that is not used outside the CPU core. The microcontroller generates a 134.
Allflex RM5 Manual 2.0 RM5 EQUIPMENT USE The RM5 module is used in all the NX Series products (cf. Table 1), and it can be used with different antennae (cf. Table 2). NX-R01 NX-R02 NX-M Table 1 – list of NX series products Model NX-R01 NX-R02 NX-R01C NX-R02C NX-R01CA NX-R02CA NX-M01C NX-M02C NX-M01CA NX-M02CA Page 7 of 11 Description Reader Box – 1x RFM. No connectors. LED indicators for power, read, exciter and high noise. Reader Box – 2x RFM. No connectors.
Allflex RM5 Manual NX-AP12060 NX-AP9045 NX-AP6040 Table 2 - List of antennae Model NX-AW50 NX-AP6040 NX-AP9045 NX-AP12060 Page 8 of 11 Description Antenna Wand 50cm Antenna Panel 60x 40cm Antenna Panel 90x 45cm Antenna Panel 120x 60cm NX-AW50
Allflex RM5 Manual 3.0 RM5 BOARD CONNECTIONS • • • • • • 4.0 LEDS – See section 4.0 RELAY1 – Used in Hooktraka mode RELAY 2 -Used in Hooktraka mode RS232- Serial tag output RNET – Communications to a NX-M SYNC – Syncronization input • • • INPUTS – Used in Hooktraka mode LED Output -Output to drive a READ and TXS led POWER – 12v power input. Both connected. LED INDICATORS 1. Power LED – Illuminates green when power is supplied. It also is used as an antenna fault condition LED. See table below.
Allflex RM5 Manual 2. Read LED – Flashes green when a RFID Transponder is in range of the Antenna Read LED Off Read LED time duty cycle None On Flashes every Cycle when a tag is in Range Fault Notes 3.
Allflex RM5 Manual 5.0 RM5 SPECIFIACTIONS General Frequency: RFID Compatibility: User Interface: RS-232 Port: RFID Code output: Input Power: 134.2Khz, Bit 1 124.2Khz +/-2Khz, Bit 0 134.2Khz +/-1.5khz ISO 11784 & 11785, HDX and FDX-B RS-232 Serial Port 9600bps, 8 Data Bits, No Parity, 1 Stop Bit. Decimal or Hex DC 12-14V, 1.5A Physical Operating Temperature: Storage Temperature: Humidity: -20c to +60c -40c to +85c 0 to 100% Performance HDX: FDX: Read Rate: Read Error Rate: Up to 1.
