DUAL-FUEL GENERATOR 8000 WATT GASOLINE / 7000 WATT PROPANE Please read and save these instructions. www.jdna.
10000W Dual-Fuel Generator Topi c Page Limited Warrant y 3 Limitations and exclusions 5 S a fet y G u i d e l i n e s 6 G e n e r a l Pr e c a u t i o n s 7 Battery 16 Assembly 17 Operation 18 Spark Plug Service 25 Inspection, Cleaning, Maintenance and Storage 26 Installation 32 Speci fications 34 General Par ts Listing 35 altitude kit altitude kit 2
10000W Dual-Fuel Generator JD North America warrants to the original purchaser who uses the product in a consumer application (personal, residential or household usage) that all products covered under this warranty are free from defects in material and workmanship for 2 years or 300 hours whichever comes first (1-year parts and labor and following 1 year parts only) from the date of purchase. All products covered by this limited warranty which are used in commercial applications (i.e.
10000W Dual-Fuel Generator JD North America JD North America 4
10000W Dual-Fuel Generator Limitations and exclusions This Limited Warranty shall not apply to: 1. Bent or broken crankshaft or resultant damage caused by vibration related to a bent or broken crankshaft. Also, damage caused by loose engine mounting bolts or improper or imbalanced accessories or blades mounted to the crankshaft. 2.
Owner’s Manual Safety Guidelines - Definitions This manual contains important information that you need to know and understand in order to protect YOUR SAFETY and to PREVENT EQUIPMENT PROBLEMS. The following symbols help you recognize this information. Please read the manual and pay attention to these sections. Save These Important Safety Instructions! Read and understand all of these safety instructions. Be sure to retain them f or future use.
10000W Dual-Fuel Generator General Precautions WARNING! FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN SEVERE IN JURY OR DEATH. CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN ALSO RESULT IN DAMAGE TO THE TOOL AND/OR THE ITEM YOU ARE WORKING ON. DANGER CARBON MONOXIDE Using a generator indoors WILL KILL YOU IN MINUTES. Generator exhaust contains high levels of carbon monoxide (CO), a poisonous gas you cannot see or smell. If you can smell the generator exhaust, you are breathing CO.
Owner’s Manual • Gasoline or oil spills must be cleaned up immediately. Dispose of fluids and cleaning materials as per any local, state,or federal codes and regulations. Store oily rags in a covered metal container. If Propane is leaking, the valve must be closed immediately. Check for leaks and deal with them immediately. • Never store fuel or other flammable materials near the generator.
10000W Dual-Fuel Generator General Precautions (cont’d) Work Area • Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Generators create sparks which may ignite the dust or fumes. • Keep bystanders, children, and visitors away while operating a generator. Provide barriers or shields as needed.
Owner’s Manual General Precautions (cont’d) Electrical Safety (cont’d) • All connections and conduits from the generator to the load must only be installed by trained and licensed electricians, and in compliance with all relevant local, state, and federal electrical codes and standards, and other regulations where applicable. • The generator must be earth-grounded for fixed installations in accordance with all relevant electrical codes and standards before operation.
10000W Dual-Fuel Generator General Precautions (cont’d) Personal Safety (cont’d) • Avoid accidental starting. Make sure the power switch is in its “OFF” position, and disconnect the spark plug wire when not in use. • Remove adjusting keys or wrenches before turning the generator on. A wrench or a key that is left attached to a rotating part of the generator may result in personal injury. • Do not overreach. Keep proper footing and balance at all times. • Use safety equipment. Always wear eye protection.
Owner’s Manual General Precautions (cont’d) Servicing Maintain labels and name plates on the generator and engine. These carry important information. If unreadable or missing, contact our service center toll free at 888-896-6881 immediately for a replacement. Generator service must be performed only by a qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a generator, use only identical replacement parts.
10000W Dual-Fuel Generator General Precautions (cont’d) Installation (cont’d) • If the generator is installed outdoors, it must be weatherproofed and should be soundproofed. It should not be run outdoors without protection to the generator and wiring conduit. • The generator weighs 220 lbs (approx). Two or more people should assist when moving or lifting this product. Never lift the generator using the engine or alternator lifting lugs. Connect lifting equipment to the frame of the generator.
Owner’s Manual General Precautions (cont’d) Mechanical (cont’d) • Do not operate the generator with safety guards removed. While the generator is running, do not attempt to reach around the safety guard for maintenance or any other reason. • Keep hands, arms, long hair, loose clothing, and jewelry away from moving parts. Be aware that when engine parts are moving fast they cannot be seen clearly. • Keep access doors on enclosures closed and locked when access is not required.
10000W Dual-Fuel Generator General Precautions (cont’d) Extension Cord If an extension cord (not included) is used, make sure to use only UL approved cords having the correct gauge and length according to the following table: Nameplate Amps (@ full load) Cord Lengths 0 ft.- 50 ft. 50 ft.-100 ft. 100 ft.-150 ft. 150 ft.-200 ft. 0-5 5.1 - 8 16 AWG 16 AWG 16 AWG 14 AWG 12 AWG 10 AWG 12 AWG - 8.1 - 12 12.
Owner’s Manual Battery To start generator electrically you will need have the battery installed correctly. This requires a 12v 18ah lawn tractor battery with the following dimensions: The dimensions are Wx7.5” Dx5” Hx7” (including terminals). A rated cranking amperage of 200. Terminals are regular, not reversed. Photos below demonstrate battery plate attachment.
10000W Dual-Fuel Generator Assembly Unpacking 1. Remove the generator and loose parts box from the carton. 2. Compare the accessory with the inventory list below. Loose Parts (Wheel kit and handle) Check all loose parts against the following list. Contact your dealer toll free at 888.896.
10000W Dual-Fuel Generator Gasoline Starting. 1、Move the GAS-LPG switch clockwise to the vertical position. 2、 Put the circuit breaker to “OFF” position. Disconnect any electric devices. 3、Put the key switch on the “RUN” positi on. The engine switch enables and disables the ignition system. STOP: To stop the engine RUN: To run the engine START: To Start the engine 4. Turn the fuel valve clockwise to the “ON” position. 5. To start a cold engine, move the choke lever to th e CLOSED position.
Owner’s Manual 6. To o perate the Recoil Start: Pull the starter grip lightly until you feel resistance, then pull briskly. Return the starter grip gently. Pulling the starter grip operates the recoil start to crank the engine To operate the Electric start: Push and hold the engine switch on the “START” position for 3~5s and crank the engine. Holding this position longer can damage the starter solenoid and void its warranty. 7.
10000W Dual-Fuel Generator 3. Fully open the LPG cylinder fuel knob. 4. Put the circuit breaker to “OFF” position. Disconnect any electric devices. 5. Move the choke lever to the “CLOSE” position. For restarting a warm engine, move the choke lever to the “OPEN” position. 6. KEY START: Turn the key to the “START” position. , When engine starts, release the key back to the “RUN” position.
Owner’s Manual 7. Move the choke lever to the “OPEN” position. 8. Push the circuit breakers to the “ON” position. Note: If you need to alternate fuel, you can change-over directly the GAS-LPG fuel switch while the generator is running at no-load. Stopping Engin e 1. Put the circuit breaker to “OFF” position. 2. Turn the engine switch to the “STOP” position . STOP 3. Turn the fuel valve lever to the “ OFF” positio n.
10000W Dual-Fuel Generator Operation (cont’d) Powering 120 Volt AC Tools And Equipment: 1. Prior to powering tools and equipment, make sure the generator’s rated voltage, and amperage capacity (120 V AC @ 66.7 AMPs) is adequate to supply all electrical loads that the unit will power. If powering exceeds the generator’s capacity, it may be necessary to group one or more of the tools and/or equipment for connection to a separate generator.
Owner’s Manual Operation (cont’d) Powering 12 Volt DC tools and Equipment: 1. Prior to powering tools and equipment, make sure the generator’s rated voltage, and amperage capacity (12V DC) is adequate to supply all electrical loads that the unit will power. If powering exceeds the generator’s capacity, it may be necessary to group one or more of the tools and/or equipment for connection to a separate generator. 2. Connect the power cord of a 12V DC powered tool or equipment to the DC Terminals.
10000W Dual-Fuel Generator Spark Plug Service In order to service the spark plug, you will need a spark plug wrench (commercially available). Recommended spark plugs: NHSP LD F7TC or NGKBPRGES but we recommend our OEM spark plug. To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. 1. Remove the spark plug cap. 2. Clean any dirt from around the spark plug base. 3. Use a spark plug wrench to remove the spark plug. 4. Visually inspect the spark plug.
Owner’s Manual Inspection, Cleaning, and Maintenance WARNING! ALWAYS MAKE SURE THE ENGINE POWER SWITCH IS IN ITS “STOP” POSITION. DISCONNECT THE SPARK PLUG WIRE FROM THE ENGINE AND ALLOW SUFFICIENT TIME FOR THE ENGINE AND GENERATOR TO COMPLETELY COOL BEFORE PERFORMING ANY INSPECTIONS, MAINTENANCE, OR CLEANING.
10000W Dual-Fuel Generator Fuel Sediment Cup Cleaning The sediment cup prevents dirt or water which may be in the fuel tank from entering the carburetor. If the engine has not been run for a long time, the sediment cup should be cleaned. 1. Turn the fuel valve to the OFF position. Remove the sediment cup, and O-ring. 2. Clean the sediment cup and O-ring in nonflammable or high flash point solvent. 3. Reinstall O-ring, and sediment cup. 4. Turn the fuel valve ON and check for leaks.
Owner’s Manual Maintenance Guide Periodic maintenance and adjustment is necessary to keep the generator in good operating condition. WARNING! Exhaust gas contains poisonous carbon monoxide. Shut off the engine before performing any maintenance. If the engine must be run, make sure the area is well ventilated. • Before each use, inspect the generator.
10000W Dual-Fuel Generator Air cleaner service A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfuncion, service the air cleaner regularly. Service more frequently when operating the generator in extremely dusty areas. WARNING! Using gasoline or flammable solvent to clean the filter element can cause a fire or explosion. Use only soapy water or nonflammable solvent. NOTE: Never run the generator without the air cleaner. Rapid engine wear will result. 1.
Owner’s Manual before use before use before use 30
10000W Dual-Fuel Generator Transporting/Storage 1.Drain the carburetor by loosening the drain screw. Drain the gasoline into a suitable container. ! WARNING Gasoline is extremely flammable and is explosive under certain conditions. Perform this task in a well ventilated area with the engine stopped. Do not smoke or allow flames or sparks in the area during this procedure. DRAIN SCREW 2. Change the engine oil 3. Remove the spark plug, and pour about a tablespoon of clean engine oil into the cylinder.
Owner’s Manual Installation NOTE: PRIOR TO POWERING TOOLS AND EQUIPMENT MAKE SURE THE GENERATOR’S RATED VOLTAGE, WATTAGE AND AMPERAGE CAPACITY IS ADEQUATE TO SUPPLY ALL ELECTRICAL LOADS THAT THE UNIT WILL POWER. IF POWERING EXCEEDS THE GENERATOR’S CAPACITY, IT MAY BE NECESSARY TO GROUP ONE OR MORE OF THE TOOLS AND/OR EQUIPMENT FOR CONNECTION TO A SEPARATE GENERATOR. Electrical and other permits may be required for the installation of emergency power systems.
10000W Dual-Fuel Generator Installation (cont’d) Supporting and Mounting Mount the generator on a concrete slab capable of supporting the weight of the generator. The slab must extend on all sides beyond the frame by at least one foot. Contact a cement contractor for slab specifications if necessary. Attach the frame to the concrete slab using 3/8” diameter expansion anchor bolts (not supplied).
AC Load 120V/240V 8000W (Gasoline) / 7000W (Propane) 10000 W (Gasoline) / 8500W (Propane) 2-AC Duplex 120V Outlets,1-120V Twist-Lock Outlet, 1-120/240V Twist-Lock Outlet EPA approved 76 /Propane 11 hours(approx.) @ 1/2 load 220 lbs.
PARTS LISTING 35
10000W Dual-Fuel Generator Cylinder head system assy. APA Part No. Description JD Pa= rt No. = Qty APGG10000-A-01-JD JF240.1.1-4 HEAD COVER COMP. BOLT 1 APGG10000-A-02-JD JF240.1.1-6 HEAD COVER WASHER COMP 1 APGG10000-A-03-JD JF240.1.1-5 WASHER COVER PACKING 1 APGG10000-A-04-JD JF240.1.3-1 HEAD COVER COMP 1 APGG10000-A-05-JD JF240.1.1-3 HEAD COVER PACKING 1 APGG10000-A-06-JD JF340.2-4 FLANGE BOLT (M10X80) 4 APGG10000-A-07-JD JF168.10-1 SPARK PLUG 1 APGG10000-A-08-JD JF240.
10000W Dual-Fuel Generator Cylinder barrel Description Qty APA Part No. JD Part No. APGG10000-B-01-JD 20.4-M6*16 HEX HEAD FLANGE BOLT (M6X 16) 2 APGG10000-B-02-JD JF340.14.1 OIL LEVEL SWITCH ASSY 1 APGG10000-B-03-JD 20.6-M10 FLANGE NUT (M10) 1 APGG10000-B-04-JD 20.4-M6*12 HEX HEAD FLANGE BOLT (M6X 12) 1 APGG10000-B-05-JD JF420.2.1-1 CRANK CASE 1 APGG10000-B-06-JD 20.2-6207 BALL BEARING (6207) 1 APGG10000-B-07-JD JF168.11.2-8 WASHER( ø8.3×ø17×1) 1 APGG10000-B-08-JD JF168.11.
10000W Dual-Fuel Generator Crankcase cover system assy. JD Part No. Description Qty APGG10000-C-01-JD JF340.17.3 DUCT COVER 1 APGG10000-C-02-JD 20.4-M8*35 FLANGE BOLT (M8 X 35) 1 APGG10000-C-03-JD JF240.15-3B OIL SCALE 1 APGG10000-C-04-JD JF340.15-5 OIL SCALE SEAL RING 1 APGG10000-C-05-JD 20.1-35*52*7 OIL SEAL 1 APGG10000-C-06-JD JF340.15-2 FLANGE BOLT (M8X35) 6 APGG10000-C-07-JD JF340.15-1B CRANKCASE COVER 1 APGG10000-C-08-JD JF340.11.
10000W Dual-Fuel Generator Crankshaft system assy. 2 D Descript io n A PA Par t N o . JD Part No. APGG10000-D-01-JD JF420.4.2 CRANKSHAFT COMP.(Tapper shaft) 1 APGG10000-D-02-JD JF340.
10000W Dual-Fuel Generator Piston & Connecting Rod Assy. A PA Par t N o . JD Pa= rt No. = Descript io n Qty APGG10000-E-01-JD JF420.3-1C COMPRESSION RING A 1 APGG10000-E-02-JD JF420.3-2C COMPRESSION RING B 1 APGG10000-E-03-JD JF420.3-3C-1 OIL RING A 1 APGG10000-E-04-JD JF420.3-3C-2 OIL RING B 1 APGG10000-E-05-JD JF340.3-6 PISTON PIN CLIP (20 mm) 1 APGG10000-E-06-JD JF420.3-5C PISTON 1 APGG10000-E-07-JD JF390.3-4 PISTON PIN 1 APGG10000-E-08-JD JF420.3.
10000W Dual-Fuel Generator Valve Train Assembly A PA Par t N o . JD Part No. Descript io n Qty APGG10000-F-01-JD JF168.1.2-17 PIVOT ADJUSTING NUT 2 APGG10000-F-02-JD JF340.1.2-8 ROCKER ARM PIVOT 2 APGG10000-F-03-JD JF340.1.2-9 ROCKER ARM 2 APGG10000-F-04-JD JF340.1.2-7 PIVOT BOLT (M8) 2 APGG10000-F-05-JD JF340.1.2-16 PUSH ROD GUIDE PLATE 2 APGG10000-F-06-JD JF340.1.2-14 ROD PUSH 2 APGG10000-F-07-JD JF340.1.2-15 VALVE LIFTER 2 APGG10000-F-08-JD JF340.
10000W Dual-Fuel Generator Recoil Starter Assy. 1 Qty A PA Par t N o . JD Pa= rt No. = APGG10000-G-01-JD JF340.13.1 RECOIL STARTER ASSY. 1 APGG10000-G-02-JD JF340.13.1-7 SETTING SCREW 1 APGG10000-G-03-JD JF340.13.1-6 SPRING RETAINER 1 APGG10000-G-04-JD JF340.13.1-8 PLATEN SPRING 2 APGG10000-G-05-JD JF340.13.1-5 STARTER DETENT 2 APGG10000-G-06-JD JF340.13.1-4 DETENT SPRING 2 APGG10000-G-07-JD JF340.13.1-3 RECOIL STARTER REEL 1 APGG10000-G-08-JD JF340.13.
10000W Dual-Fuel Generator Fan Cover Assy. Qty A PA Par t N o . JD Part No. Descript io n APGG10000-H-01-JD JF420.12-1 SHROUD APGG10000-H-02-JD 20.4-M6*12 FLANGE BOLT (M6 X 12) 4 APGG10000-H-03-JD JF340.13.2 FAN COVER COMP.
10000W Dual-Fuel Generator Carburetor Assy. 3 1 4 2 APA Part No. JD Part No Description 5 Qty APG10000GL-I-01-JD JF420GL.9-4 PROPANE SUPPLY HOSE 1 APG10000GL-I-02-JD JF420GL.9.2 CARBURETOR 1 APG10000-I-03-JD JF340.9-3 CARBURETOR PAPER GASKET 1 APG10000-I-04-JD JF340.9-1A CARBURETOR INSULATING PLATE 1 APG10000-I-05-JD JF340.
10000W Dual-Fuel Generator Flywheel Assy. 5 2 4 3 J A PA Par t N o . JD Part No. Descript io n Qty APGG10000-J-01-JD JF420.4.1 FLYWHEEL 1 APGG10000-J-02-JD JF168.4.2-2 SPECIAL WOODRUFF KEY 1 APGG10000-J-03-JD JF340.12-1 COOLING FAN 1 APGG10000-J-04-JD JF340.13-1 STARTER PULLEY 1 APGG10000-J-05-JD JF240.
10000W Dual-Fuel Generator Ignition System Assy. Qty A PA Par t No . JD Pa= rt No. = APGG10000-K-01-JD JF340.10.2-1 NOISE SUPPERSSOR CAP ASSY 1 APGG10000-K-02-JD JF340.10.2-2 IGNITION COIL ASSY 1 APGG10000-K-03-JD JF340.10.2-3 STOP SWITCH CORD 1 APGG10000-K-04-JD JF340.10-3 STOP SWITCH CORD HOLDER 1 APGG10000-K-05-JD 20.4-M6*25 FLANGE BOLT (M6 X 25) 1 APGG10000-K-06-JD JF340.
10000W Dual-Fuel Generator Starter Motor Assy. Qty APA Part No. JD Part No. Descript io n APGG10000-L-01-JD JF340.18-1 STARTER MOTOR 1 APGG10000-L-02JD JF340.18-2 SOLENOID 1 APGG10000-L-03-JD 20.
10000W Dual-Fuel Generator Control Assy. Qty A PA Par t N o . JD Part No. APGG10000-M-01-JD JF340.11.4 CONTROL ASSY. 1 APGG10000-M-02-JD JF340.11.4-1 CONTROL BASE COMP. 1 APGG10000-M-03-JD JF340.11.4-3 CONTROL ADJUSTING SPRING 1 APGG10000-M-04-JD JF340.11.4-4 PAN SCREW (M5 X 34) 1 APGG10000-M-05-JD 20.4-M6*12 FLANGE BOLT (M6 X 12) APGG10000-M-06-JD JF340.11.2-5A THROTTLE RETURN SPRING APGG10000-M-07-JD JF340.11.2-6 GOVERNOR SPRING 1 APGG10000-M-08-JD JF340.11.
10000W Dual-Fuel Generator Muffler Assy. 3 4 N Part No. APA Part No. Descript io n APG10000-N -01-JD 20.4-M8*16 FLANGE BOLT (M8 X 16) 4 APG10000-N -02-JD 20.4-M6*12 FLANGE BOLT (M6 X 12) 4 APG10000-N -03-JD JD6500.17.10.1.5-1 MUFFLER STAY COMP. 1 APG10000-N -04-JD JD6500.17.10.1.5-2 MUFFLER PROTECTOR SEAL 1 APG10000-N -05-JD JD6500.17.10.1.5-3 MUFFLER SIDE PROTECTOR 1 APG10000-N -06-JD JF340.7.2-3 MUFF. INNER PROTECTOR COM 1 APG10000-N -07-JD JF340.7.
10000W Dual-Fuel Generator Air Cleaner Qty APA Part No. JD Part No. APGG10000 -O-01-JD JF240.6.2-1 AIR CLEANER COVER COMP 1 APGG10000 -O-02-JD JF240.6.2-2 AIR CLEANER ELEMENT 1 APGG10000 -O-03-JD 20.6-M5 FLANGE NUT (M5) 6 APGG10000 -O-04-JD JF240.6.2-4 AIR CLEANER SEPARATOR 1 APGG10000 -O-05-JD JF240.6.2-3 AIR CLEANER SEAL 1 APGG10000 -O-06-JD JF240.6.2-5 AIR CLEANER CASE COMP 1 APGG10000 -O-07-JD JF240.6.
10000W Dual-Fuel Generator Fuel Tank Assy. 1 2 9 10 P 5 6 3 6 4 7 8 APA Part No. JD Part No Descript io n APGG10000 -P-01-JD JD6500W-U.1.5-1.2 FUEL TANK CAP COMP. 1 APGG10000 -P-02-JD JD6500W-U.1.5-1.1 FUEL FILTER 1 APGG10000 -P-03-JD JD10000W-U.1.5-1C FUEL TANK COMP. 1 Qty APGG10000 -P-04-JD JF168.8-1A FUEL TUBE 1 APGG10000 -P-05-JD JF168.8-5 FUEL SWITCH 1 APGG10000 -P-06-JD JF168.8-3 CLAMP, FUEL TUBE 2 APGG10000 -P-07-JD JF168.
10000W Dual-Fuel Generator Control Box Assy. 4 10 1 2 13 14 3 11 6 12 5 5 7 8 9 Description Q QTY APA Part No. JD Part No. APGG10000 -Q-01-JD HC001-MB CONTROL PANEL COMP. 1 APGG10000 -Q-02-JD 21.3.1-13 ENGINE SWITCH ASSY. 1 APGG10000 -Q-03-JD 21.3.4-15 DC 12V OUTPUT 1 APGG10000 -Q-04-JD 21.3.16-2 HOURS METER 1 APGG10000 -Q-05-JD 21.3.4-5 120V RECEPTACLE(Ru-22) 1 APGG10000 -Q-06-JD 21.3.7-7 CIRCUIT BREAKER (SINGLE, 20A) 1 APGG10000 -Q-07-JD 21.3.
10000W Dual-Fuel Generator Frame Comp Assy. 2 1 APA Part No. Description JD Part No. Qty APGG10000-R-01-JD JD6500.17.10.1-J109 GENERATOR FRAME 1 APGG10000-R-02-JD 21.3.25-11 .
10000W Dual-Fuel Generator Generator 7 11 APA Part No. JD Part No Description Qty. APGG10000 -S-01-JD 7KW.25.3A STATOR COVER 1 APGG10000 -S-02-JD 7.5KW.25.02B STATORASSY 1 APGG10000 -S-03-JD 5KW.25.2-8A COOLING FAN 1 APGG10000 -S-04-JD 5KW.25.4A BRUSH ASSY 1 APGG10000 -S-05-JD 20.4-M5*16*0.75 TAPPING SCREW 3 RR HOUSING 1 APGG10000 -S-06-JD JF240.22-1 APGG10000 -S-07-JD 20.9-M5 SPRING WASHER (5mm) 4 APGG10000 -S-08-JD 20.
10000W Dual-Fuel Generator Generator APA Part No. JD Part No. Description Qty HEX.BOLT (M5 X 20) 2 2KW.25.5-1 VOLT CHANGE TERMINAL BR-AC-W 1 20.9-M5 PLAIN WASHER (5mm) 4 APGG10000-S-18-JD 20.4-M5*16*0.
10000W Dual-Fuel Generator Wheel & Hand Assy.3 7 7 7 14 14 16 15 1 2 2 6 4 6 4 5 12 12 15 16 13 9 11 9 9 9 7 6 6 3 2 2 1 14 14 13 10 11 8 8 T APA Part No JD Part No Description Qty. APGG10000 -T-01-JD JD6500.17.10.1-1 PIN SPLIT 2 APGG10000 -T-02-JD JD6500.17.10.1-2 WSHER PLAIN 4 APGG10000 -T-03-JD 8 inch wheel WHEEL 2 2 APGG10000 -T-04-JD JD6500.17.10.1-J109.1-1 BAFFLE APGG10000 -T-05-JD JD6500.17.10.1-J109.1 SHAFT 1 APGG10000 -T-06-JD 20.
