Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com Appendix H: Client: Alinco, Inc. Model: DJ-S45T Standards: FCC 15.121 & IC RSS-215 Report: 2005166 Manual Please see the following pages.
UHF FM TRANSCEIVER DJ-S45 CQ/T/E Instruction Manual Thank you for purchasing this ALINCO FM transceiver. This instruction manual contains important safety and operating instructions. Please read it carefully before using the transceiver and be sure to keep it for future reference. ALINCO, INC.
Contents Contents NOTICE / Compliance Information Statement .....................3 Before Operating the Transceiver .........................................5 1.Functions and Features .......................................................6 1-1 Standard Accessories ..............................................................6 2.Accessories ..........................................................................7 2-1 Attaching and Detaching Accessories.....................................
Contents 4-7 Receiving ..............................................................................20 4-7-1 Adjusting Squelch Level ..............................................20 4-7-2 Monitor Function..........................................................21 4-8 Transmitting ..........................................................................21 4-8-1 Switching of Transmission Output Level ( DJ-S45 T/E only) ........................................................22 5.Parameter Setting Mode ...
NOTICE / Compliance Information Statement NOTICE / Compliance Information Statement DJ-S45 T This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
NOTICE / Compliance Information Statement UHF FM Transceiver DJ-S45 T This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Before Operating the Transceiver Caution The use of transceiver in the following places is prohibited. •Aboard aircraft •In airports •In ports •Within or near the operating area of business wireless stations or their relay stations. Before using the transceiver in any of the above places, obtain any necessary permission from the proper authorities, and be mindful of the local laws that govern radio operation.
1.Functions and Features 1. Functions and Features ■ 39 different Tone Squelch function (CTCSS) ■ TOT (Time Out Timer) function ■ Tone Call function (ALT, 1750, 2100, 1000, 1450Hz) ■ Reception Bell (Beeper) function ■ DJ-S45 T/E 3 types of Scan function (VFO, Memory, Tone) 1 4 types of Scan function (LPD (VFO), Memory, Tone, PMR) ■ Cable Cloning ■ Rain Proof DJ-S45 CQ Caution Insert the rubber covers properly and firmly into the jacks of the external speaker, microphone, and power supply.
2.Accessories 2. Accessories 2-1 Attaching and Detaching Accessories 2 2-1-1 Antenna( DJ-S45 T/E only) 1. Hold the antenna by its base and turn it clockwise until it stops. Check to be sure the antenna is securely connected. 2. Turn the antenna counter-clockwise to detach it. Caution The DJ-S45 CQ takes fixed type antenna due to a legal requirement. NEVER try to detach it. 2-1-2 Hand Strap 1. Attach the hand strap in the upper slot at the rear of the transceiver as shown in the illustration.
2.Accessories 2-2 Setting Batteries 1. Open the cover latch and then open the cover. Cover latch Cover 2. Set two commercially available AA batteries in the +/- orientation marked at the internal front side. 2 3. Close the cover and then fix it with the cover latch. 2-3 Lithium Ion Battery Pack [EBP-60] (Option) Please refer to the instruction manual that comes with the battery pack for operating and charging procedures.
2.Accessories 2-4 Battery Level Indicator 2 •Battery consumption level may change depending on the surrounding temperature or the frequency of use. •Even if the battery icon appears to indicate the necessity of charging the battery, it can be used further if the usage is only for low output transmission or reception. Battery icon *When the battery level becomes low, the battery icon appears. Charge or replace the battery.
3.Control Functions 3. Control Functions 3-1 Names and Operations of the Transceiver Controls ■ Top and Front Views ① ④ 3 ⑤ ③ ② ① ⑥ ⑦ ⑧ ⑨ No. Name ① Power/Volume Dial ② MIC Connector ③ SP Connector ④ RX/TX Lamp ⑤ ⑥ Speaker F key ⑦ ⑧ ⑨ Display (LCD) Keypad Microphone Functions Switches power ON/OFF, and also adjusts the audio volume. For connection of the optional external microphone (2k Ω) with 2.5 ø stereo plug. For connection of the optional external speaker(8 Ω) with 3.
3.Control Functions ■ Side Views ⑩ ⑩ ⑭ ⑫ 3 ⑪ ⑬ Antenna side No. ⑩ ⑪ ⑫ ⑬ ⑭ 11 Dial side Name Functions Undetachable fixed type antenna. DJ-S45 CQ Install the included antenna. Choose an DJ-S45 T/E SMA Antenna Connector antenna which has low SWR (standing Wave Ratio) if you purchase one. PTT (press to talk) key While this key is held down, the transceiver transmits. When the key is released, the transceiver returns to the receive mode.
3.Control Functions 3-2 Key Operations ① ② 3 ③ ④ ⑤ ⑥ No. Name ① PTT ② MONI ③ F/SET ④ ▼/T SQL ⑤ V/M / MW ⑥ ▲/RPT Independent operation After pressing F key Transmits or completes the setting in the Setting mode. Activates the monitoring Switches the key lock ON/OFF (page 34). function. Accesses Various functions. DJ-S45 T/E Adjusts the frequency in 1MHz step(page 17). Decreases the frequency Sets the tone squelch function (page 36~38). and memory channels.
3.Control Functions ① ② 3 ③ ④ ⑤ ⑥ No. Name ① PTT 13 ② MONI ③ F ④ ▼/T SQL ⑤ ⑥ ▲/RPT Pressed for a while Enables transmission while holding. Activates the monitor operation while holding (page 21). Activates the Setting mode (page 28). Pressed shorter than 2 sec., starts downward scanning, and pressed longer than 2 sec., decreases the value continuously (page 30~33). During transmission Transmits tone call signal (page 21). DJ-S45 T/E Sets the transmission output level low (page 22).
3.Control Functions 3-3 Display ① ② ③ ⑤ ⑥ ④ ⑦ ⑧ ⑨ ⑩ No. ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮ ⑯ ⑰ ⑱ Name 3 ⑭ ⑪⑫⑬ ⑮ ⑯ ⑰ ⑱ Indication Appears when the F key is pressed. Appears when keys are locked. Indicates the shift (+/-) direction. Appears when the tone encode (ENC) is set. Appears when the tone squelch is set. Appears when the bell function is ON. Blinks during memory writing mode. Indicates memory No. in the Memory mode and setting No. in the Setting mode.
4.Basic Operations 4. Basic Operations 4-1 Turning the Power ON Rotate the dial clockwise. 4 Dial Caution The dial also performs adjusting the audio volume. Therefore, do not rotate it far, otherwise the audio may be too loud. To turn the power OFF, rotate the dial counter-clockwise until it clicks. 4-2 Adjusting the Audio Volume To increase:Rotate the dial clockwise. To decrease:Rotate the dial counter-clockwise.
4.Basic Operations 4-3 Operating Modes The DJ-S45 T/E has two operating modes; VFO and Memory. The DJ-S45 CQ has three operating modes; LPD (VFO), PMR and Memory. ■ Switching among modes Every time you press the V/M key, you can change the operating mode as shown in the diagram. DJ-S45 T/E VFO Memory 4 DJ-S45 CQ LPD (VFO) PMR Memory 4-4 LPD (VFO) Mode The factory setting is the LPD (VFO) mode.
4.Basic Operations 4-4-1 Frequency Setting When ▲/▼ keys are pressed, the frequency increases and decreases in tuning steps. 4 ■ Adjusting the Frequency in 1MHz Steps( DJ-S45 T/E only) Press the F key twice, and then the MHz figure of the display blinks. Press ▲/▼ keys while the figure is blinking to adjust the frequency in the 1MHz increments. 4-5 PMR Mode( DJ-S45 CQ only) The frequencies of PMR channels have already been programmed accordingly. PMR mode 4-5-1 Frequency Number Setting 1.
4.Basic Operations 4-6 Memory Mode The Memory mode is used to call up on a previously programmed frequency. This transceiver has 100 memory channels (0~99CH). 4-6-1 Memory Channel Programming 1. Switch to the LPD (VFO) or PMR mode by pressing the V/M key. 2. Select the desired frequency or channel. 3. Press the F key, and then press the V/M key while the "F" icon appears. The memory channel No. and the "W" icon blinks. 4 Memory Channel No. 4. Select a memory channel to program by pressing the ▲/▼ keys.
4.Basic Operations 4-6-2 Selecting a Memory Channel 4 1. Switch to the Memory mode by pressing the V/M key. The memory channel No. appears on the display. The Memory mode is not activated if there is no preprogrammed data in the Memory channels. By pressing ▲/▼ keys, memory No. increases and decreases by programmed channels in numerical order. Memory mode 4-6-3 Clearing a Memory Channel Data 1. Switch to the Memory mode by pressing the V/M key. 2.
4.Basic Operations 4-6-4 Programmable Items to Memory Channel The following data can be stored in each memory channel. •Frequency •Offset Frequency •Shift Direction •Tone Frequency •Skip CH Setting •Tone Encoder / Decoder Settings •Busy Channel Lock Out (BCLO) 4 4-7 Receiving 1. Turn the power ON. 2. Rotate the dial to adjust the audio volume. 3. Eliminate the noise by setting the squelch. Refer to "Adjusting Squelch Level" below. 4. Select the desired frequency or channel.
4.Basic Operations 4-7-2 Monitor Function •While the MONI key is pressed, the squelch opens and noise is heard from the speaker regardless of the squelch setting. "BUSY" appears on the display. •Weak signals under the squelch threshold level can be heard, using this function. •Monitoring the selected frequency can be performed even if the tone squelch is set. 4 4-8 Transmitting 1. Select the desired frequency or channel. 2. Press and hold the PTT key, speak into microphone with normal loudness and tone.
4.Basic Operations 4-8-1 Switching of Transmission Output Level( DJ-S45 T/E only) Transmission power can be changed to HI/LO by pressing the ▲/▼ keys while transmitting. "LO" appears on the display when the transmitting power is low, and "HI" appears when the transmitting power is high. Initial setting is "HI".
5.Parameter Setting Mode 5. Parameter Setting Mode In the Setting mode, you can set various functions of the DJ-S45 CQ/T/E . 5-1 Selectable Parameters Please refer to "5-2 Selecting the Setting Mode" (page 28) for how to enter to the Parameter Setting mode and "9-1 Resetting" (page 43) for the initial factory (default) settings. The ITEM No. increases when the F key is pressed, and it decreases when MONI key is pressed.
5.Parameter Setting Mode ■ 00.600 Offset frequency setting ITEM No. 03 DJ-S45 T/E 03 DJ-S45 CQ LPD (VFO) mode This function sets the width of the frequency shift (0-99.995MHz). ■ bEP-on Beeper ON/OFF ITEM No. 04 DJ-S45 T/E 04 DJ-S45 CQ LPD (VFO) mode 01 DJ-S45 CQ PMR mode Select ON to enable a beep that sounds after certain keys are touched and/or setting is done. ■ ALt Call tone setting ITEM No.
5.Parameter Setting Mode ■ bS-on Battery saving ON/OFF ITEM No. 08 DJ-S45 T/E 08 DJ-S45 CQ LPD (VFO) mode 05 DJ-S45 CQ PMR mode Select ON to save the battery consumption during the stand-by status. ■ bEL-oF Bell ON/OFF ITEM No. 09 DJ-S45 T/E 09 DJ-S45 CQ LPD (VFO) mode 06 DJ-S45 CQ PMR mode The bell function can inform you a signal is being received by a tone sound and LCD indication (Bell icon) like a pager. ■ Stb-on 5 Stand-by-beep ON/OFF ITEM No.
5.Parameter Setting Mode ■ SCAn-t Scan (timed/busy channel) switching ITEM No. 12 DJ-S45 T/E 12 DJ-S45 CQ LPD (VFO) mode 09 DJ-S45 CQ PMR mode Choose between timed scan (SCAn-t) and busy channel scan (SCAn-b). Refer to "6-1 Scanning"(page 30) for details. ■ m**-oF Scan skip setting ITEM No. 13 DJ-S45 T/E 13 DJ-S45 CQ LPD (VFO) mode 10 DJ-S45 CQ PMR mode Memory channel numbers that you want to skip while in Memory Scan operation.
5.Parameter Setting Mode ■ SHIFt ITEM No. ■ 05.000 ITEM No. ■ tonE ITEM No. ■ 88.5 ITEM No. 5 Repeater shift direction setting 17 DJ-S45 T/E Repeater offset frequency setting 18 DJ-S45 T/E Repeater tone encoding ON/OF 19 DJ-S45 T/E Repeater tone frequency setting 20 DJ-S45 T/E Above items No.17 to 20 are related to "Quick-Repeater-Access" ONLY. Refer to page X for operation. ITEM No. 17 and 18 set the same parameters as explained in ITEM No.2 and 3, ITEM No.
ITEM NO.
5.
6.Advanced Operations 6. Advanced Operations 6-1 Scanning Use this function to automatically search for signals. When a signal is received, scanning pauses, and resumes after a while depending on the settings of scanning mode. ■ Scanning Modes Timed Scan:While the scan is pausing, when the signal disappears, the scan resumes and moves to the next channel. Even if a signal is being received, the scan resumes after five seconds.
6.Advanced Operations 6-1-1 LPD (VFO) Scan Scans the entire band in the LPD (VFO) mode. 1. Switch to the LPD (VFO) mode by pressing the V/M key. 2. Press and hold the ▲/▼ keys for 1 to 2 seconds to start scanning. The decimal point blinks during the scan. Scanning direction goes upward by pressing the ▲ key, and downward by pressing the ▼ key. 6 3. To stop scanning, press the PTT key, the F key or the V/M key. While MONI key is being pressed, scanning stops temporarily and monitor function is activated.
6.Advanced Operations 6-1-3 Memory Scan Scans only the programmed memory channels. 1. Switch to the Memory mode by pressing the V/M key. 2. Press and hold the ▲/▼ keys for 1 to 2 seconds to start scanning. The decimal point blinks during the scan. The operation is the same as the LPD (VFO) scan. 3. To stop scanning, press the PTT key, the F key or the V/M key. While MONI key is being pressed, scanning stops temporarily and monitor function is activated. When the key is released, scanning restarts.
6.Advanced Operations 6-1-5 Tone Scan This function helps you to find the tone frequency in case CTCSS system is used. 1. Press and hold the ▲/▼ keys for 1 to 2 seconds in the tone squelch setting mode (page 36~38). LPD (VFO) mode Scanning starts and the decimal point blinks. 39 kinds of tone frequencies are scanned in order. When the tone frequency matches, PMR mode scanning stops and you can hear the received signal. Scanning will not resume until the ▲/▼ keys are pressed again. 6 2.
6.Advanced Operations ■ Quick-Repeater-Access Operation 1. Press the V/M key to activate the LPD (VFO) mode. 2. Press the F key, then the ▲ key while the "F" icon appears. The "XX" icon appears on the display and the repeater function is set. The shift frequency, direction and tone set in the Setting mode (page 27, ITEM No.17 to 20) are applied automatically. 3. To cancel this function, repeat the procedure step 2, and the "XX" icon will disappear.
6.Advanced Operations 6-4 Tone Call (Tone Burst) Use this function to call a partner by adding an audible tone to the transmitting signal. The tone signal is output while the MONI key is pressed down while the PTT key is pressed and held. The call tone sound can be selected in the Setting mode (page 24, ITEM No.05). Use this function to access tone burst system repeaters by selecting proper tone. Caution A tone call signal cannot be output with a tone ENC signal.
7.Selective Communicating 7. Selective Communicating When communicating with a specific station, tone squelch (CTCSS) function can be used. Tone squelch is a function that enables to receive the signal only when its encoding tone matches to your tone decode setting. There are 39 different selectable tone frequencies/numbers. No. 01 02 03 04 05 06 07 08 09 10 Frequency 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 No. 11 12 13 14 15 16 17 18 19 20 Frequency 94.8 97.4 100.0 103.5 107.2 110.9 114.
7.Selective Communicating 4. Press the PTT key or the V/M key to complete the setting and return to the LPD (VFO) mode. When "T" is displayed, the tone ENC is set. Only the tone transmitting functions operates (encode). When "T SQ" is displayed, the tone squelch is set. Both the tone transmitting functions and the tone squelch operate (decode). The CTCSS operation is deactivated when none of icons appear. Reference : Monitoring can be performed by pressing the MONI key even during setting operation.
7.Selective Communicating 7-2 PMR Tone Squelch ( DJ-S45 CQ only) 1. Press the V/M key to activate the PMR mode. 2. Press the F key, then the T SQL key while "F" icon appears. The tone number blinks. The default setting is "09". 3. Change the tone number with ▲/▼ keys. Select the tone number to use from the list above. 4. Press the PTT key or the V/M key to complete the setting and return to the PMR mode. Select OFF (oF) to disable the tone squelch operation.
8.Cloning / Packet Operation 8. Cloning / Packet Operation 8-1 Cloning When using the cloning function, all setting information (including memory data) of one transceiver (master unit) can be transferred and copied to another transceiver (slave unit) by connecting them with a cable. ■ Connecting the Transceivers Connect the external speaker jacks on both the master and slave transceivers with commercially available φ 3.5 stereo mini plug cable. If you prefer to make one, please refer the chart below.
8.Cloning / Packet Operation ■ Transmitting the Master Data 1. Press and hold the MONI key and press the PTT key three times. "CLONE" appears on the display to indicate the Clone mode is activated. 2. Press the PTT key on the master unit. "Sd ***" is displayed and the datatransfer starts. "PASS" appears when the cloning completes. Turn the power OFF after "PASS" is displayed. If the data is not transmitted correctly, "PASS" is not displayed. Turn the power ON again, and repeat the procedure from step 1.
8.Cloning / Packet Operation ■ Receiving the Master Data 1. "Ld ***" appears on the slave unit's display while the master data is being transmitted. "End" appears when the cloning completes. 2. Turn the transceiver power OFF. Caution •Do not disconnect the cable while cloning. •All data in the slave transceiver will be updated to the master transceiver's data during the cloning operation. Be sure you want to overwrite the data before cloning.
8.Cloning / Packet Operation 8-2 Packet Operation( DJ-S45 T/E only) Packet operation is one of the data communication methods, which enables data transmission and reception with personal computer through TNC. ■ Packet Operation Connections 3.5¿ PLUG SP SP T GND GND 2.5¿ PLUG 10µF MIC MIC 3.0V N C 10k½ PTT GND GND (Low) 3.0V Power is supplied from internal 3V line through a 100½ resistor. Connection figure of the packet operation with this unit is shown above.
9.Maintenance and Reference 9. Maintenance and Reference 9-1 Resetting When you reset the transceiver, all settings are returned to the initial factory (default) settings. 1. Turn the power ON while the F key and V/M key are held down. 2. While all the display indications appear, release the keys. Initial Factory Settings 9 43 DJ-S45 DJ-S45 CQ T E LPD (VFO) mode PMR mode Frequency 445.000MHz 433.000MHz 434.
9.
10.Specifications 10. Specifications ■ DJ-S45 CQS/CQL General Frequency Range Modulation Ant. Impedance Supply Voltage Current Transmit (DC6.0V) Receive Frequency Stability Dimension Weight LPD (VFO) mode PMR mode TX;433.06000-434.78000MHz TX;446.00625-446.09375MHz RX;433.06000-434.78000MHz RX;446.00625-446.09375MHz F3 50 Ω 3.0-6.0VDC(DC-JACK), 2xAA Batteries, Li-ion pack LPD (VFO) mode PMR mode Approx.0.45A Approx.0.20A Approx. 60mA +5~-5ppm 57(W) x98 (H) x27.
10.Specifications ■ DJ-S45 T/E General Frequency Range Modulation Ant. Impedance Supply Voltage Current Transmit (DC6.0V) Receive Frequency Stability Dimension Weight DJ-S45 T DJ-S45 E TX: 420.000-449.995MHz TX: 430.000-439.995MHz RX: 420.000-473.995MHz RX: 430.000-439.995MHz F3 50 Ω 3.0-6.0VDC(DC-JACK), 2xAA Batteries, Li-ion pack Hi-Power Lo-Power Approx.0.45A Approx.1.00A Approx. 60mA +5~-5ppm 57(W) x98 (H) x27.9 (D) mm (Projections exclusive) Approx.
ALINCO, INC. Head Office:Shin-Dai building 9th Floor 2-6, 1-Chome, Dojimahama, Kita-ku, Osaka 530-0004, JAPAN Phone:+81-6-4797-2136 Fax: +81-6-4797-2157 E-mail:export@alinco.co.jp Printed in Japan Copyright Alinco, Inc.