Rhein Tech Laboratories 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com APPENDIX H: Client: Alinco, Inc. Model: DJ-C7T Standards: FCC 15.121/IC RSS-215 Report #: 2004067 Date: April 22, 2004 MANUAL Please see the following pages.
VHF/UHF FM TRANSCEIVER DJ-C7 T/E Instruction Manual Thank you for purchasing this ALINCO transceiver. This instruction manual contains important safety and operation instructions. Please read it carefully before using the transceiver and be sure to keep it for future reference. ALINCO, INC.
NOTICE / Compliance Information Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Contents Before Operating the Transceiver..................................... Attention ..................................................................................... Points to Note Before Transmitting............................................. Points to Note When Using an External Power Supply .............. 1. Functions and Features................................................. 1.1 Standard Accessories .......................................................... 2. Accessories................
7. Cloning ........................................................................... 7.1 Cloning ................................................................................. ■Connecting the Transceiver .......................................... ■Receiving the Master Data ............................................ ■Transmitting Data from the Master Transceiver ............ 8. Maintenance and Reference ......................................... 8.1 Troubleshooting.....................................
Before Operating the Transceiver Attention • Do not open the case or touch the interior components. Tampering can cause equipment. • Do not expose the transceiver to direct sunlight, dusty places or place it near sources of heat. • Keep the transceiver away from TVs, tuners or other equipment if it interferes with reception. • Securely connect the antenna included with the transceiver. • When transmitting for a long time, the transceiver can overheat.
1. Functions and Features 1 • 39 CTCSS tone squelch settings • Tone burst function (1000,1450,1750 and 2100Hz) • Split function • Cloning • Li-ion Battery adoption 2 Functions and Features / Accessories 2. Accessories 2.1 Attaching the Accessories ■Connecting and Disconnecting the Antenna • Connecting 1.Connect the helical antenna to the antenna connector at the upper left corner. 2.Hold the helical antenna by its base, and turn it clockwise until it stops.
■Attaching and Detaching the Battery Pack • Attaching Projections 1.Align the projections on the battery pack with the pits on the transceiver. Pits Latch • Detaching 1.Push the latch upward. Latch • The battery pack is not charged when shipped. It must be charged before using. • The battery pack can be charged by mounting it on the DJ-C7 and connecting AC adaptor for charge of battery to the DC power supply jack on the transceiver.
■Prevent Short Circuiting the Battery Pack Be extra cautious when carrying the battery pack; shortcircuiting will produce surge current possibly resulting in fire. 2 ■Battery Recharger (EDC-126) • Recharging AC adaptor plug Accessories Power plug Terminals 1.Mount the battery pack on the transceiver. 2.Connect AC adaptor plug to the external power supply jack on the transceiver. 3.Connect the power plug in an outlet.
3. Control Function 3.1 Name and Operation of the Transceiver Controls ■Top and Front Views Item 1 2 SP/MIC Connector 2 Dial 3 TX/RX Lamp 4 Keypad 5 FUNC Key 6 Microphone 7 8 9 Speaker Power Key Display (LCD) 9 4 8 5 6 7 3 For connection of the optional external speaker (8Ω) and microphone (2kΩ) with 2.5ø stereo plug. Rotate this dial to select transmitting / receiving frequency, memory channel, and other functions.
■Side View Item 3 Control Function 10 SMA Antenna Connector 11 PTT Key 12 MONI Key 13 DC-IN Jack 10 11 12 10 13 Description For connection of the included helical antenna. If you use other antenna, choose one with low SWR (Standing Wave Ratio) designed for VHF and UHF frequencies. Press this key to transmit. When the key is released, the transceiver returns to a receiving state. When this key is pressed, the squelch is unmuted and you can hear the received signal.
3.2 Keypad 3 Control Function Key V/M SCAN BAND FUNC PWR Dial Independent Operation Switches between VFO and Memory mode. (See on P.XX) Starts and stops scanning. (See on P.XX) Switches between bands. (See on P.XX) Press FUNC While F is ON Programs to memory channels. (See on P.XX) Sets Tone Squelch setting. (See on P.XX) Sets Shift setting. (See on P.XX) Dial Operation with Holding Key Switches between Busy and Timer scan. (See on P.XX) Adjusts frequency in 1 MHz unit. (See on P.
3.3 Display 1 3 16 Control Function 15 4 5 6 14 13 12 12 3 2 11 10 9 9 8 7 1 Appears when the 2 Appears when keys are locked. 10 Appears when the battery save function is on. 3 Indicates the shift (+/-) direction or split operation. 11 Appears when the auto power off function is activated. 4 Appears when the tone squelch is set. 12 Appears when the reverse tone squelch is set. 5 Appears when the bell function is on. 13 Appears when the repeater mode is on.
4. Basic Operations 4.1 Turning the Power ON Hold the second. 4.2 Adjusting the Audio Volume key down for a • There are 31 volume levels. (00-30) • Default is set as 10. 1. Press the dial once. To turn the power OFF, hold the key down until the display disappears. will be displayed on the LCD indicating the present volume level. 4 Basic Operations Caution When you turn it on through the external power supply of a voltage of over 6.
4.3 Adjusting the Squelch The squelch is a function for eliminating noise which is generated when none of the signals are monitored. "To open squelch" means that the DJ-C7 monitors any of the higher signals than the squelch level you set, and the receiving sound will be heard. • There are 10 squelch levels. (0-9) • Default is set as 3. 4 1. Press the dial twice. 4.4 Operating Modes The DJ-C7 has two operating modes; VFO mode and Memory (MR) mode.
■Entry Completion Digit for Different Tuning Steps 4.5 VFO Mode This is a mode which is set as the factory-shipped configuration. Radio frequencies and various settings can be changed by rotating the dial in this mode. 1. Press the key to select the band to be changed its tuning step. ■Switching the Band Everytime you press the BAND key, below 7 bands can be switched in order. 145.000(142.000~169.995MHz) 380.000(380.000~429.995MHz) 433.000(430.000~469.995MHz) .531(531~1620kHz) 1.625(1.625~9.995MHz) 76.
4.6 Memory Mode This mode allows you to program frequencies into the DJ-C7 memory. A programmed frequency is called as a channel. The DJ-C7 has four types of memory functions; Memory channel (general), Program scan channel, Priority channel, and VFO auto programmed channel. ■Types of Memory Memory channel (general) (0-199) 4 Basic Operations Program scan channel (OA, Ob-4A, 4b) Priority channel (PRI) VFO auto programmed channel (AH, AL) This is a channel which is called up in Memory mode.
■Clearing a Memory Channel ■Contents of Memory Channel The following settings can be stored in each memory channel. 1. Set Memory Write Protect function to "OFF" state, if necessary. For more information on this function, please refer to "Memory Write Protect function" on P.XX. 2. Press the key to switch to the Memory mode. 3. Rotete the dial to select the memory channel number you want to delete. 4 key while the Basic Operations 4. Press the key, and press the F icon appears on the LCD.
4.7 Receiving 1. Adjust a volume level. (See on P.XX) 4.8 Transmitting 1. Select a frequency on which you want to transmit signals. 2. Adjust a squelch level. (See on P.XX) 2. Press the PTT key. 4 Basic Operations 3. Select a frequency on which you want to receive signals. When the red TX/RX indicator lights, it is now ready for transmitting.
5. Advanced Operations 5-1 Scanning 3. Release the This function automatically detects receiving frequencies to help you locate the signal that you want to receive. There are two types of scanning; Busy scan and Timer scan. The default is set as Busy ("bUSY") scan. Switching between those two types can be done in the Setting mode. (See on P.XX) Busy scan: If no signal is monitored after scanning stops, it will detect the next frequency.
4. Rotate the dial in the clockwise direction to make the scanning take place in the UP direction. Conversely, rotate the dial in the counter-clockwise direction to make the scanning take place in the DOWN direction. 5. Press any key other than the MONI key to stop scanning. ■Memory Scan Scanning is performed to detect signals among programmed frequencies as the memory channels. Memory channels need to be set in advance. Otherwise, the following operations can't be done.
5.4 Priority This function monitors two frequencies alternately to increase efficiency for receiving signals. Every 5 seconds, the DJ-C7 momentarily switches from a specified frequency to the frequency which is programmed as a priority channel (see on P.XX) for 0.5 seconds. 1. Hold the key down for a second to start the Priority monitoring function. 5.
6. Repeat steps from 1 to 4, and press the the state of step 4. key in After "XX" is displayed, press the key again to display . With the OFF state, press the PTT key or leave 5 seconds as it is to release the Tone Squelch function. 7. While "XX" is displayed on the LCD, press the PTT key or leave 5 seconds as it is to perform the Reverse Tone Squelch. To release the Reverse Tone Squelch function, press the PTT key or leave 5 seconds as it is while "XX" is displayed.
6. Parameter Setting Mode The DJ-C7's Setting mode is used to set the various operating functions. 6.1 Mode Setting Items (1) Audio Volume Level (2) Antenna Type (3) Repeater function (4) Tone Burst Frequency (5) APO (Auto Power Off) 6.2 Selecting the Setting Mode 1. Press the key, and press the dial once while the F icon appears on the LCD. It switches to the Setting mode, and the item name will be displayed on the LCD. 2. Select an item by pressing the dial.
1. " 6.3 Selecting the Parameters The following 11 functions can be set in the DJ-C7's Setting mode. " is displayed on the LCD. 2. Rotate the dial to select an antenna between Earphone and External (SMA) as follows. "SmA" (1) Audio Volume Level -> "EAr" When you use an earphone, you may reduce entire volume level with this function if the volume is too loud. (3) Repeater function 1. " " is displayed on the LCD. 2. Rotate the dial to switch HIGH/LOW of the volume level as follows.
(5) APO (Auto Power Off) This function automatically turns the power OFF if there is no key operation for a specified period of time to prevent battery charge wastage. This is useful if you easily forget to turn off the transceiver. 1. " • The factory-shipped default is set as ON. • This function will be released temporarily when the DJ-C7 receives signals or there is a key operation. • This function will not be performed while the DJ-C7 is under scanning. • LCD displays even with the hibernation state.
(11) AM / FM (9) Memory Write Protect function This function prevents from overwriting or deleting memory channels by mistake and protects what you've programmed. You can always program frequencies to blank channels regardless of this setting. 1. " You can select a modulation mode between AM and FM. It is necessary to switch a display for setting a tuning step in a specified band in advance. For more information on this, please refer to "Entry Completion Digit for Different Tuning Steps" on P.XX.
7. Cloning 2. Wait for a while until master data is transferred completely. 7.1 Cloning With the Cloning function, it is possible to connect two transceivers by a cable, and copy all settings from one unit (call as a Master) to the other (call as a Slave). This function transfers all master's settings including memory channel data. ■Connecting the Transceiver • Connect both of the speaker jacks on the sending transceiver (Master side) and the receiving transceiver (Slave side) with a ø 2.
2. Press the dial. " " is displayed on the LCD, and the master's transceiver starts to transfer data. " " is displayed on the LCD when transfer is completed successfully. 3. Turn the power OFF on the master's side to release the Clone mode. 7 Cloning If the DJ-C7 should fail to transfer data, " " is displayed on the LCD. When you see the indicator, redo from step 1.
8. Maintenance and Reference 8.1 Troubleshooting Please check the list below before concluding that the transceiver is faulty. If a problem persists, reset the transceiver. This may correct erroneous operations. Symptom Nothing appears on the display when you turn the power on. No speaker audio. No reception. Possible Cause Action Poor Li-ion battery pack connection Check if the battery pack terminals are clean. Dead battery. Recharge the battery pack. You are releasing the key too quickly.
8.2 Resetting 8.3 Options When you reset the transceiver, all settings are returned to the initial (default) factory setting. You can reset programmed channel memory when the write protect is off. 1. Press and hold the to turn the power on. key and press the 2. Release the keys when all icons are displayed. The transceiver returns to the initial VFO mode.
8.4 Transmission System DJ-C7T: 144.000-147.995 MHz 420.000-449.995 MHz DJ-C7E: 144.000-145.995 MHz 430.000-439.995 MHz DJ-C7T: 144.000-147.995 MHz DJ-C7E: 144.000-145.995 MHz MIC Audio frequency amplification limiter low pass filter BA4510FV VHF-VCO 2SC5066FT Buffer amplifier 2SC5066FT PLL MB15A01 Buffer amplifier 2SC5066FT Excitation amplifier µPC2771TB ANT Power amplifier 2SK3078A 12.6 MHz UHF-VCO 2SC5066FT 8 Maintenance and Reference DJ-C7T: 420.000-449.995 MHz DJ-C7E: 430.000-439.
9. Specifications ●General ●Transmitter 144.000 - 147.995MHz (T Version) 144.000 - 145.995MHz (E Version) 420.000 - 449.995MHz (T Version) UHF 430.000 - 439.995MHz (E Version) 88.100 - 107.995MHz (T Version) FM Radio 87.500 - 107.995MHz (E Version) RX 108.000 - 173.995MHz (T Version) Frequency VHF 144.000 - 145.995MHz (E Version) Range 380.000 - 511.995MHz (T Version) UHF 430.000 - 439.995MHz (E Version) F3E Modulation 50ohm (SMA) Antenna Impedance External Terminal 3.7 - 6.
VHF/UHF FM HANDHELD TRANSCEIVER 144.000 - 145.995MHz / 430.000 - 439.995MHz AUS F I E B D LUX S DK GR NL UK FIN IRE P CE0336! This device is authorized for use in all EFTA member states (CH, ICE, LI, NOR). An operator's license is required for this device.
ALINCO, INC. Head Office: Shin-Dai Building 9th Floor 2-6-1 Dojimahama, Kita-ku, Osaka 530-0004, Japan Phone: +81-6-4797-2136 Fax: +81-6-4797-2157 E-mail: export@alinco.co.