360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com APPENDIX I: MANUAL Scanning Receiver Certification Report Alinco, Inc.
DJ296 INSTRUCTION MANUAL 1. INNOVATIVE AND NEW FEATURES . Comes equipped 39 CTCSS Tone Squelch function. . Comes equipped 104DCS Digital code squelch function. . TOT (Time Out Timer) can be set to a Duty Cycle most accommodating to the user’s requirements. . Alphanumeric channel name function. . Tone burst function (1750, 2100, 1000, 1450 Hz) . Nine Autodial memories easily accessed from the DTMF keypad with redial function. . Direct frequency entry from DTMF function. . Burglary Alarm Function .
. CONTROLS/FUNCTIONS Top, Front, Sides and Rear View 4 3 2 9 10 11 1 5 7 12 6 8 1. LCD DISPLAY PANEL Refer to LCD Display section of this manual. 2. MAIN TUNING DIAL The main tuning dial/knob may be rotated in either direction to select RX/TX frequency and volume/squelch level. 3. EXTERNAL MICROPHONE JACK When the external microphone is prefered, plug in a 2.5mm stereo plug into this jack. 4. EXTERNAL SPEAKER JACK When the external speaker is prefered, plug in a 3.5mm mono plug into this jack. 5.
. LCD Display 1 2 3 4 6 5 7 8 9 20 18 12 19 10 11 13 14 15 16 17 1. F When the F icon appears, secondary function keys may be activated. 2. + It indicated the plus or minus offset direction. 3. T It appears when the tone encoder is activated. 4. TSQ It appears when the tone squelch is activated. 5. DCS It appears when the digital code squelch is activated 6. The “ “icon appears when the key and frequency Lock is activated. 7.
Operation Manual DJ296 Contents 5 Operation 1(Basics) 5-1 Adjusting the Volume 5-2 Adjusting the Squelch 5-3 Receiving 5-4 Transmitting 5-5 Frequency Selection 5-6 Channel Step 5-7 Shift Direction and Offset Frequency 5-8 Memory Channel Operation 5-9 CALL Channel Operation 5-10 Scanning 5-11 Output Power Switching 5-12 Key Lock Function 5-13 Tone Burst Function 5-14 Auto Power Off Function 5-15 Battery Save (BS) Function 5-16 Lamp Function 5-17 Monitor Function 5-18 Beep Function 5-19 Clock Shift Function 6
5 Operation 1 (Basics) 5-1 Adjusting the Volume . [VOL] appears on LCD when VOL key is pressed, volume level is displayed. The initial value is 00 (minimum). The volume can be increased or decreased by rotating the dial. The maximum value is 20. There are 21 steps from 00-20 in volume adjustment. The setting value can be kept even while the power is off. . When the volume point data is (00), the voice can not be heard. Press any key (except for FUNC, MONI key) to complete the setting.
[UP/DOWN with channel step] 1. Rotating the dial clockwise increases frequency 1 channel step/1 click, and rotating counterclockwise decreases the frequency 1 channel step/1 click. [1MHz UP/DOWN] 1. Press the [F] key then rotate the dial while [F] icon is ON, the frequency increases or decreases by 1MHz depending on the direction of the rotation. [Keypad Direct Entry] The frequency is set with the numerical keys of 0~9. Setting 1. Enter the 100MHz digit. 2. Enter the 10MHz digit. 3. Enter the 1MHz digit. 4.
width may be compensated. 5-7 Shift Direction and Offset Frequency Usually the repeater is used in the duplex mode. Namely the signal received with a certain frequency is transmitted with another frequency. The difference between these frequencies is the offset frequency. The setting range of the offset frequency is from 0 to 99.995MHz. 1. Press and hold the F key, then press 2/SHIFT key while [F] icon is ON. The current offset frequency and shift direction will appear.
When the memory channel is programmed, [M] appears on the LCD. 3. Press and hold the FUNC key, then press MW key while [F] icon is ON. A beep sounds, and the programmed frequency will be erased. Then [M] starts flashing. 4. While [M] is flashing, the erased memory is still displayed on the LCD. Press and hold the F key then press the MW key again, the erased memory can be recovered. If CH or mode had been changed, the recovery is not available.
(1) VFO SCAN 1. Press the V/M key to enter VFO mode. 2. Press the SCAN key to start scanning. The decimal point of the frequency on the LCD starts flashing to indicate the scanning is started. The unit scans by a channel step to the last direction of operation. 3. Rotate the dial clockwise to scan upward and counterclockwise to scan downward. VFO SCAN covers all receiving frequency range for scanning. 4. Press any key (except for MONI key) to stop scanning. (2) Memory Scan 1.
When tone and DCS are set, the signal will be transmitted with tone frequency and DCS code. 5-14 Auto Power Off Function The function prevents the battery from consuming when you forget to turn off the power switch. (1) Setting Press and hold the F key, then press 6/APO key while F icon is ON. [APO] appears on the LCD and the auto power off function is programmed. . The initial setting is OFF. . To release the APO, press and hold the F key then press 6/APO key while F is ON .
In the unlikely event that CPU clock noise is present on a particular operating frequency programmed into the radio, you can shift the CPU clock frequency to avoid the CPU clock noise, which normally is so weak that it is inaudible even if the radio is tuned exactly to its frequency. CPU clock can be shifted in the set mode. 6 Operation 2 (Applications) 6-1 Selective Calling When you communicate with the specific station, tone squelch function or DCS function is useful.
Changing both of tone encoder/tone decoder frequencies 1. Set the tone encoder in the tone squelch setting mode. (T icon is ON.) Change the tone encoder frequency with dialing, then the setting is completed. 2. When memory is programmed in this mode, the current tone frequency will be programmed to both of encoder frequency and decoder frequency. Changing the tone decoder frequency only 1. The tone squelch is programmed in the tone squelch setting mode. (T.SQL icon is ON.) 2.
6 digits are displayed, and nothing appears at first. 2. Select the dialer memory NO. with the dial. 3. For example, when you input 1 2 3 4 5 6 7 8 9, the LCD displays as shown below: [ 1] - [ 1 2] - [ 1 2 3 ] [ 1234]-[123456]-[234567]-[345678]-[456789] 4. Press and hold the F key, then press 0 key while F icon is ON, pause can be set instead of the code. Pause is indicated by [ - ]. Entering a pause puts a gap between transmission of codes.
1. When the DTMF code is transmitted using the auto dialer, the code is transmitted with programmed burst/ pause time. The initial setting is 60ms. DTMF first digit's burst time 2. When the DTMF code is transmitted using the auto dialer, the code will be transmitted at the programmed first digit burst time. The initial setting is 60ms. 3. WAIT time cannot be changed while CH is displayed.
6-12 TOT Penalty Function When the transmission is completed by the TOT function, the transmission will be inhibited within the programmed TOT Penalty time. The transmission is inhibited during the penalty time. 1. TOT Penalty function and its penalty time can be programmed in the set mode. If the PTT key is pressed during the TOT Penalty time, an alarm tone will sound. 2. The penalty will be cancelled if you keep holding down the PTT key until TOT expires and also TOT Penalty time elapses.
If data transfer is failed, "PASS" does not appear on the LCD. Try again from the first. 7-2 Burglary Alarm Function If someone tries to steal your transceiver, an alarm goes off from the speaker. Setting Be sure to set the battery pack. 1. Plug the external DC power plug cord to the car battery, etc. 2. Set to SCR-ON in the set mode. 3. Turn off the power switch of the unit. . To release the setting, set to SCR-OF in the set mode. Operation .
1. [BS-ON] appears on the LCD. 2. Rotate the dial, and the display toggles as shown below. Then ON and OFF are switched repeatedly. ..downward upward….. ……BS-ON - BS-OF ………. …………………………………. [No.2] Scan Type Selection 1. [TIMER] appears on the LCD. 2. Rotate the dial, and the display toggles as shown below. The scan types are switched repeatedly. .downward upward….. …..TIMER …..BUSY ….. ………………………….. [No.3] Beep Tone ON/OFF 1. [BEP-ON] appears on the LCD. 2. Rotate the dial to set to [BEP-OF]. 3.
The setting is available up to max. 15 seconds. [No.8] DTMF WAIT time 1. [DWT-01] appears on the LCD. 2. Rotate the dial, and the display toggles as shown below. Then the DTMF WAIT time will be changed. 3. ** shows the current DTMF WAIT time. The initial setting is 0.1 second, and [DWT-01] appears on the LCD. 4. Rotate the dial to change the DTMF WAIT time. ……Downward…………………..Upward…………… …..DWT-01….DWT-04……DWT-07….. DWT-10 …… ………………………………………………………….. [No.9] DTMF Burst/Pause Time 1.
…………MRS-OF …..MRS-ON……….. …………………………………………… 9 RESET Function Press and hold the F key, then turn on the power. The unit returns to the factory's default setting. …………………………………………………………………………………………………….. VFO frequency 223.500MHz CALL frequency 223.500MHz Memory channel a blank SHIFT setting none SHIFT frequency 1.6MHz Channel step 5kHz …………………………………………………………………………………………………….. . Press and hold the F key, the LCD's all segments are turned ON. When you release the F key, the reset will be performed.