DS-225 series 1
Contents 1. Warning & Statements。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 2. Voltage。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 3. Device Application。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 4. Technical Specifications。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 5. Structure Overview。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 6. Installation & Sandpaper Replacement。。。。。。。。。。。。。。。 7. Installation & viscid disc Replacement。。。。。。。。。。。。。。。 8. Connection Set for Dust Outlet。。。。。。。。。。。。。。。。。。。。。。 9. Switch& Speed Governor Operation。。。。。。。。。。。。。。。。。 10.
12. Suction adjustment。。。。。。。。。。。。。。。。 13. LED light (Optional)。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 14. Application Diagram。。。。。。。。。。。。。。。。。。。。。。。。。。。 15. Cleaning。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。 16. Replacement of carbon brush。。。。。。。。。。。。。。。。。。。。 1) Work area a) Keep work area clean and well lit. Cluttered and dark areas may result in an accident. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions.
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious bodily injury. b) Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, protective eyewear, or hearing protection used for appropriate conditions will reduce personal injuries.
ensure these are connected and properly used. Use of these devices can reduce dust related hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will deliver better results and safer at the rate for which it was designed for. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
are less likely to bind and are easier to control; g) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations other than it was intended for could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
devices, may also occur if the supply voltage falls below rated voltage. 2. Device Application As one of our products, the device belongs to the hand-held electric tools. The device mainly caters for lime surface, including the interior wall, ceiling, exterior wall, corridor, etc. Remove the painting lime mud from the wall, and make the surface even or smooth. It may promote the wall grinding efficiency and quality by workers.
Frequency 60（Hz） Rated Power 750（W） No-load Speed 800-1750 (R/min) Sandpaper Dimensions Spindle Thread Ф225（mm） M14 Safety Standard II / Net/Gross Weight 13.8（Lbs） 4．Structure Overview (See following pictures) Complete appliance DS-225 28.7x10.8x17.5（in/2pc） Length 4.1FT/5.
DS-225AVS 28.7x10.8x17.5（in/2pc） Length 4.1FT/5.
DS-225-2 44x11x7.4（in/1pc）Length 4.1FT/6.
DS-2252VS 44x11x7.4 ( in/1pc ) Length 4.1FT/6.
DS-225-2 Plastic viscid disc component 2. Sandpaper 4. Speed governor 3.
5. Dust Outlet 6.Vacuum dust hose 7. Handle 8.
9.
5. Installation & Sandpaper Replacement (See following picture) Note: Prior to installation or removing the sandpaper, make sure to not only switch off the device, but also cut off the power supply.
——Installation Guide To ensure the replacement procedures, place the device on smooth and even ground prior to installation. Take the sandpaper from the toolbox, and attach it onto the disk. The back of the sandpaper (Item 1) will automatically glue with the disk/adhesive disk (Item 2), making both connection and conduction available. In order to promote the grinding efficiency, it is necessary to change the sandpaper after the device has been operational for a certain period.
6. Installation & viscid disc Replacement (See following picture) If the viscid disc is damaged during use, a new viscid disc can be purchased from our company for replacement. 。 ——Installation Guide Viscid disc Remove the sandpaper, put the Allen wrench into the hexagon hole in the center of the viscid disc and then rotate anticlockwise to take off the damaged viscid disc. Install the new viscid disc (see the picture). 7.
a b Component b Lock a As the name implies, it is used for connecting the device to Dust Outlet (accessory). The dust will come out from the wall upon operating the grinder.
reduce the amount of dust. ——Installation Guide Plug the component b into component, make the lock in the groove and rotate clockwise. ——Dismantling Process Rotate the lock anticlockwise and pull out the dust hose 8. Switch & Speed Governor Operation The switch of the machine is a two step switch. As shown in following picture, press the switch button and push forward to power on. Press the switch button and turn back to power off.
9. The operation of the edge angle Disc side cover Disk If closer contact with the wall is needed, please remove the corner plate of the sander.
10. Folding installation and disassembly The main board long straight tubes, the upper and lower joint of folding, folding screw locking hand-wheel on the joint. Then insert the extension rod, a locking hand-wheel screw on the handle on the contrary can be removed.
Locking hand wheel 12.
Suction adjustment guide: suction adjustment knob can adjust the suction level. It is advised to have the suction on the first setting and increase suction power according to needs. 13. LED light (Optional) When working in the dusky condition, LED light could be added for help.
14.
Ceiling position With the tension spring machine, motor back hook arm on both sides of the hole allows for easier polishing of the ceiling. 15. Cleaning Regular cleaning shall be conducted after grinding. ● Cleaning the devices frequently may help extend operating life and reduce repair rate. It is recommended to clean the connection sets and components of electric motor without application of water. ● Timely cleaning is recommended after each use of the devices.
Carbon brush replacement position 27
CE Declaration of conformity The following product complies with safety requirements of the CE-Directive based on its design and type: Product Description: Electric disc-type sander ( Pole-mounted) Type of Product: DS-225series Year of Product: 2016 Satisfies the requirement EC-Machinery Directive 2006/42/EC of the Council Directive*: EC-Low Voltage Directive 2006/95/EC EC-Directive of Electromagnetic Compatibility 2004/108/EC and conforms with the norms**: EN 60745-1:2009+A11 EN 60745-2-3:2011 EN
