Reader User Guide ISO8030 & ISO8030BT Series Portable Wand Including Aleis DataLink Version Draft A – 10/06/2009 IMPORTA T! This User Guide must be read in conjunction with Reader, prior to use. Copyright Aleis Pty Ltd 2008 13429 A1064AUS Aleis Pty Ltd ACN 130 754 826 www.aleis.
Aleis 8030 Series Operational Manual Aleis 8030 Series 2 of 34
Aleis 8030 Series Operational Manual Regularity otices and Conformity ................................................................................................................................ 4 Part 1: Important User Instructions ............................................................................................................................... 5 1.0 8030 Reader Instructions .................................................................................................................
Aleis 8030 Series Operational Manual Regularity otices and Conformity USA – FCC Information to the user (FCC Part 15.105) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Aleis 8030 Series Operational Manual Part 1: Important User Instructions 1.0 8030 Reader Instructions IMPORTA T Must be read prior to using system USER I STRUCTIO S The following instructions must be wholly adhered to or permanent damage to the antenna/reader and/or permanent data loss can occur. Non-conformance to the handling and operating instructions will immediately void all warranties for the antenna/reader and software. 1.
Aleis 8030 Series Operational Manual 2.0 The 8030 Keypad 3.0 8030 Series Reader Method of Use Helpful Hints First, it is recommended to go to Menu Setup diagram in User Guide, then go to ME U key on reader, and become familiar with the settings in the reader while looking at the User Guide. Pressing C once takes you back to previous step. Keep session numbers recorded somewhere so you know which cattle are recorded in individual session numbers.
Aleis 8030 Series Operational Manual 3.3 How to: Create Sessions using F1 and F2 Keys. 1. Press F2 to end current session. 2. Press F1 to start new session. Four Beeps will be heard. Note: you can start a new session even if the one you have ended has no RFID devices in it. 3.4 How to: Upload RFIDs into the Reader The feature of uploading RFIDs into the 8030 portable wand is to allow you to find particular RFIDs that you need to identify.
Aleis 8030 Series Operational Manual Step 2: Upload the files into the reader. 1. Open up Aleis DataLink. 2. Once the software has found the reader, click on the Open button located at the left side of the DataLink screen (there is a big yellow manilla folder on the button). 3. Find the file that you created, and click on the open button. 4. You will see that file name listed in the main screen of Aleis DataLink where the session names and numbers are normally displayed. 5. Click on that file name. 6.
Aleis 8030 Series Operational Manual 3.6 Formatting the File System Formatting of the file system is very important to keep your reader operating at its maximum performance. Once the reader has read and stored a lot of tags eg 40000+ you may notice a slow down in its performance when storing and recalling data. This is similar to your PC when the Hard Drive gets full. When you clear the reader it doesn’t actually remove the data so you can retrieve it if you accidentally have cleared the reader.
Aleis 8030 Series MENU Memory Status Reader Information System Setup Read Setup Session 8030 Series Menu Tree Turn Unit ON 4.
No RF Signal being received. Two very quick beeps (every 30 seconds) Aleis 8030 Series No Charge—unit will turn off Half Charged Fully Charged Legend for LCD Visual Displays. Battery Level Indicator (Solid) Connected BATTERY LOW 11 of 34 (Flashing) Flashes as unit is about to turn off. 6 Auxiliary LED’s – 3 each side of the screen No Signal—no IDs will be sent Signal at 2/3 Strength Signal at Full Strength RF Signal Indicator Current RFID number, eg.
Aleis 8030 Series Operational Manual 6.0 Menu Main Menu (Reader selection choices) 6.1 Sesssion ew -New Session Send to PC Send to PC Current Session All Sessions Clear Clear Current Session All Sessions Select - Selects Session number and count. 6.
Aleis 8030 Series Operational Manual 6.3 System Setup Communications Interface Select Interface Serial RF Modem Bluetooth Protocol Select Protocol Tiris Aleis Combined (Tiris/Aleis) Allflex USA Serial Baud Rate 9600 38400 57600 115200 Tag Format ISO 26 Digit ISO 27 Digit 16 Digit Scale Interface No Scales Ruddweigh Thunderbird Tru-Test Display Backlight Threshold (Select required lighting Eg 1 = always bright. 16 = will come on when very dark.
Aleis 8030 Series Operational Manual Load Defaults Load Defaults 8030/50 Series 9030/50/60 Series Set Date/Time -Sets Date and Time 6.4 Reader Information (This is for technical assistance only & product identification) Reader Info Hardware: Software: Date: Serial o: Reader Type: (Hardware Version) (Software Version) (Software Date) (Reader Serial Number) (Aleis Reader Model) 6.
Aleis 8030 Series Operational Manual 7.0 Battery Charging Charge for 24 hours for 1st initial charge. Aleis suggests a form of transient protection unit be used while charging the reader to help prevent power surges/spikes. The batteries in the unit can be charged by using the 6-pin connector on the side of the unit. When the battery charger is plugged in, it will automatically turn the reader ON. This is completely normal – you do not need to turn the unit OFF.
Aleis 8030 Series Operational Manual 7.4 Battery Charging Options An optional Car Cigarette Lighter Battery Charger is available. 7.5 Alternative Recharging Methods Contact Aleis for alternative methods of charging. 8.0 The Clock on the 8030 Reader The clock on the 8030 Reader is what will put the date and time stamp on each RFID that is read by the reader.
Aleis 8030 Series Operational Manual Aleis DataLink Software 10.0 Aleis DataLink Software IMPORTA T Must be read prior to using software This software has been purposefully designed to download the RFID’s and/or respective data relating to those RFID’s from the Aleis 7000 8030/50 and 9030/50/60 Series Readers. Aleis accepts no responsibility for any form of improper use, negligent or otherwise, resulting in the loss of RFID’s with the use of this software.
Aleis 8030 Series Operational Manual 10.1 Aleis DataLink Installation To install DataLink: 10.2 1. Place the DataLink CD into the CD drive; the program will automatically begin installation. If not Go to My Computer Double click on the CD Rom Drive Browse the CD and Double click on the icon called DataLink 2. Follow the installation prompts, and click on Finish when installation is complete.
Aleis 8030 Series Operational Manual 10.
Aleis 8030 Series Operational Manual 10.4 Producer Transfer (Australia Only) This opens the NLIS Transfer Wizard, using the selected fields in the current session(s). This button is used for Producer to Producer transfers. For further information please use the help feature in Aleis DataLink. Producer Transfer Steps Step 1 Click on the "Producer Transfer" button.
Aleis 8030 Series Operational Manual Step 3 After completing the form Click on "Next" If you choose to tick the Upload Later box the Transfer will not be completed but you can complete the transfer at any time by resuming the upload from the Upload Centre. The PIC From PIC To and Vendor Dec/Waybill No. can be loaded straight into the form if the fields PI1, PI2 and VEN were used as Data entry on Data entry readers.
Aleis 8030 Series Operational Manual Step 4 Click on the "Start" box On a successful or unsuccessful transfer you will get a message in the status box.
Aleis 8030 Series Operational Manual 10.5 3rd Party Transfer (Australia Only) This opens the NLIS Transfer Wizard, using the selected fields in the current session(s). This button is used for Third Party transfers with or without written permission. For further information please use the help feature in Aleis DataLink 3rd Party Transfer Steps Step 1 Click on the "3rd Party Transfer" button.
Aleis 8030 Series Operational Manual Step 3 After completing the form Click on "Next" If you choose to tick the Upload Later box the Transfer will not be completed but you can complete the transfer at any time by resuming the upload from the Upload Centre. The PIC From PIC To and Vendor Dec/Waybill No. can be loaded straight into the form if the fields PI1, PI2 and VEN were used as Data entry on Data entry readers.
Aleis 8030 Series Operational Manual Step 4 Click on "Yes" You have to accept this agreement to finish the transaction You will then be presented with the following Box Step 5 Click on the "Start" Box On a successful or unsuccessful transfer you will get a message in the status box.
Aleis 8030 Series Operational Manual 10.6 Retrieve Tag Bucket (Australia Only) This opens the NLIS Transfer Wizard, to retrieve all RFID and NLIS ID tag numbers that match a specific PIC from the NLIS database. You can also retrieve the Lifetime Traceability (LT), EU Status (EU), Last Transfer Date (TFR) and the Issue Date (ISS) For further information please use the help feature in Aleis DataLink Retrieve Tag Bucket Steps Step 1 Click on the "Retrieve Tag Bucket" button.
Aleis 8030 Series Operational Manual Step 2 After completing the form Click on "Next" You will then be presented with the following Box Step 3 Click on "Start" The Tag Bucket will be loaded into the main screen of DataLink.
Aleis 8030 Series Operational Manual 10.7 Tag Replacement (Australia Only) This opens the NLIS Tag Replacement Request form using the selected tags in the current session. This button is used for replacing defective RFID tags. For further information please use the help feature in Aleis DataLink Tag Replacement Steps Step 1 Click on the "Tag Replacement" button.
Aleis 8030 Series Operational Manual Step 2 Type in the Replacement tag and the Broken tag in the boxes below Step 3 Click on the "Add Request" Box and the tags will be inserted into the box below.
Aleis 8030 Series Operational Manual You will be presented with the following Box Step 5 After completing the form Click on "Next" You will be presented with the following Box Step 6 Click on "Start" Aleis 8030 Series 30 of 34
Aleis 8030 Series Operational Manual On a successful or unsuccessful tag replacement you will get a message in the status box 10.8 LIS Upload Centre (Australia Only) This opens the Upload Centre screen, which displays all transactions with the NLIS database. Both successful and unsuccessful transactions are displayed and information regarding the transaction.
Aleis 8030 Series Operational Manual 11.0 Aleis Conditions of Sale 1. In these conditions: (1) `Vendor' means Aleis Pty Ltd ACN 130 754 826 of the Cnr Old Rosevale & Jandowae/Kingaroy Rds, Jandowae, Queensland, 4410 which is the seller of the goods (2) ‘Factory’ means the Vendor’s principal place of business at the Cnr Old Rosevale & Jandowae /Kingaroy Rds, Jandowae, Queensland 4410. (3) Purchaser' means the customer(s) described overleaf which is the purchaser of the goods.
Aleis 8030 Series Operational Manual 12. (3) Vendor shall not be liable for and purchaser releases vendor from any claims in respect of faulty or defective design of any goods supplied unless such design has been wholly prepared by vendor and the responsibility for any claim has been specifically accepted by vendor in writing and in any event vendor's liability hereunder shall be strictly limited to the replacement of defective parts in accordance with para 11(1) of these conditions.
Aleis 8030 Series Operational Manual 23. The Purchaser shall pay all and any import duties, levies or imports and/or any sales, use, excise, gross receipts, value added, goods and services tax, property or other taxes or duties of any kind whatsoever assessed upon or relating in any way to the goods ordered by the Purchaser irrespective of the person, nation, state or authority requiring payment thereof. 24.