User's Guide

ManualsBrandsALE USA ManualsElectronicsOmniAccess Stellar

Alcatel-Lucent Enterprise

OmniAccess Stellar AP1360 Series

Installation Guide

060492-10 Rev. A

*060492-10 Rev. A*

https://www.al-enterprise.com

The Alcatel-Lucent name and logo are trademarks of Nokia used under license

by ALE. To view other trademarks used by affiliated companies of ALE holding,

visit: https://www.al-enterprise.com/en/legal/trademarks-copyright. All

other trademarks are the property of their respective owners. The

information presented is subject to ALE without notice. Neither ALE Holding

nor any of its affiliates assumes any responsibility for inaccuracies contained

herein. (2019)

1. Introduction

The high performance and rugged OAW-AP1360 series

supports IP67 standard for harsh outdoor environments,

such as exposure to high and low temperatures, persistent

moisture and precipitation, and electrical interfaces

include industrial strength surge protection. The OAW-

AP1360 series supports a maximum concurrent data rate of

1.267Gbps (867Mbps in 5GHz and 400Mbps in 2.4GHz), and

dual Gigabit Ethernet links, integrated omni-directional

antennas, it is ideal for medium density outdoor

environments.

1.1. Package Contents

Item

Name

Qty

Unit

Outdoor Access Point

Pcs

Quick Start Guide

Pcs

Installation Guide

Pcs

Regulatory Compliance

and Safety Information

Pcs

User Guide Info Card

Pcs

Cable Gland

pcs

Figure 1: Product Packing

◆ Outdoor AP mounting kit package, which contains

the following items. (To be ordered separately)

Table 1

Item

Description

Graphics

Qty

Mounting bracket（D1）

Mounting bracket（D2）

Mounting bracket（D3）

Item

Description

Graphics

Qty

Spacing tube

Screw bolt M8 x 65

Screw bolt M8 x 25

Screw bolt M6 x 12

Spring washer Φ8

Spring washer Φ6

D10

Screw nut M8

D11

Locknut M8

D12

Hose clamp

(102-152mm)

D13

Expansion bolt M6x60

NOTES：

⚫ Component dimensions are in metric.

⚫ The weatherproof caps for Ethernet and Console are

connected to the AP, not loose in the package.

⚫ Do not open or remove the Protective vents.

⚫ Inform your supplier if there are any incorrect, missing,

or damaged parts. If possible, retain the carton,

including the original packing material. Use these

materials to repack and return the unit to the supplier

if needed.

1.2. Hardware Overview

Figure 2: OAW-AP1361/OAW-AP1361D Front View

Figure 3: OAW-AP1362 Front View

Figure 4: OAW-AP1361/OAW-AP1361D Rear View

Figure 5: OAW-AP1362 Rear View

Figure 6: OAW-AP1361/OAW-AP1361D Bottom View

Figure 7: OAW-AP1362 Bottom View

1.3. Pre-Installation Checklist

Before installing your OAW-AP1360 Series, be sure that you

have the materials and tools listed below：

⚫ IEEE 802.3af compliant PoE source.

⚫ Gigabit Ethernet cable of required length and RJ45

connector.

⚫ Grounding wire #8AWG of required length.

⚫ Tools:

◼ Ratchet wrench

◼ Hexagon sockets

◼ Screw driver

◼ Rotary hammer

◼ Percussion bit Φ8

◼ Ratchet Crimping Plier for non-insulated

terminal

◼ Crimping Tool for RJ45 Modular Plug

◼ Ethernet cable tester.

◼ Heat shrinkable tube

◼ Heat gun

1.4. Deployment Process Overview

The deployment of an Access Point typically consists of the

following stages:

⚫ WLAN Planning—The administrator determines how

many APs will be needed for their wireless network

strategy and where they will be deployed.

⚫ AP Installation—Each AP can be physically installed at

proper location. Each location should be as close as

possible to the center of the intended coverage area

and should be free from obstructions or obvious sources

of interference.

⚫ AP Configuration—The administrator defines the

operational behavior for each AP, such as RF

characteristics and security features.

NOTES:

⚫ Installing the Outdoor Access Point requires

professional training. The AP must be professionally

installed by a qualified engineer familiar with WLAN

system.

⚫ For AP configuration information, please refer to the

User Guide.

2. Installing the AP

2.1. Using the Mounting Kits

2.1.1. Assembling Access Point(A) with

Mounting bracket(D1), to get

Subassembly (E1)

2.1.1.1. Materials Preparation

Table 2

Item

Description

Graphics

Qty

Access Point

OAW-AP1360 series

Mounting bracket（D1）

Screw bolt M6 x 12

Spring washer Φ6

2.1.1.2. Assembly Processes

Step-1. Connecting the AP(A) with Mounting

bracket(D1)

Step-1

Step-2. Get Subassembly (E1)

Step-2

Note：

⚫ Must use a proper Ratchet wrench to tighten the Screw

bolt(D7)

2.1.2. Assembling Mounting bracket(D2)

with bracket(D3), to get

Subassembly(E2)

2.1.2.1. Materials Preparation

Table 3

Item

Description

Graphics

Qty

Mounting bracket（D2）

Mounting bracket（D3）

Spacing tube

Screw bolt M8 x 65

Spring washer Φ8

D10

Screw nut M8

D11

Locknut M8

2.1.2.2. Assembly Processes

Step-3. Insert the Mounting bracket (D2) into bracket

(D3), and align Mounting bolt hole(A) with

Mounting bolt hole(B).

Step-3

Step-4. To get a required installation angle of pitch,

adjusting the Dowel pin(A) on Bracket(D2) to

match up with the Positioning teeth of

Mounting bracket(D3)

Step-4

Step-5. Insert the Spacing tube (D4) into bracket (D2),

align the hole of the tube (D4) with the

Mounting bolt hole (B) of bracket (D2).

Step-5

Step-6. From the side of bracket (D3), where Dowel pin

(B) stands, put the Screw bolt (D5) through the

Mounting bolt hole(A) and stick out at the

other side. Make sure the Screw bolt goes

through Mounting bracket(D3), bracket(D2)

and Spacing tube(D4) in sequence. Then put a

Spring washer (D8) and a Screw nut (D10) on

it in sequence. Finally, tighten the Screw nut

(D10) with ratchet wrench.

Step-6

Step-7. To prevent the screw nut from loosening and for

better reliability, put a Locknut(D11) on the

end of the Screw bolt(D5). Then tighten it up

with ratchet wrench.

Step-7

Note：

⚫ Must use a proper Ratchet wrench to tighten the Screw

nut(D10) and the Locknut(D11)

Step-8. Get Subassembly (E2)

Step-8

2.1.3. Assembling Subassembly(E1) with

Subassembly(E2), to get Final-

Assembly (F)

2.1.3.1. Materials Preparation

Table 4

Item

Description

Graphics

Qty

Subassembly（E1）

Subassembly（E2）

Screw bolt M8 x 25

Spring washer Φ8

D10

Screw nut M8

D11

Locknut M8

2.1.3.2. Assembly Processes

Step-9. Overlap Subassembly (E1) to Subassembly

(E2), align the Mounting bolt hole(C) with

Mounting bolt hole(D).

Step-9

Step-10. To get a required horizontal angle, adjusting

the Dowel pin(C) on Bracket(D2) to match up

with the Positioning teeth of Bracket (D1).

Summary of content (3 pages)

PAGE 1
Alcatel-Lucent Enterprise OmniAccess Stellar AP1360 Series Installation Guide Item Description Graphics Qty D4 Spacing tube 1 D5 Screw bolt M8 x 65 1 D6 Screw bolt M8 x 25 1 D7 Screw bolt M6 x 12 3 D8 Spring washer Φ8 2 D9 Spring washer Φ6 3 D10 Screw nut M8 2 Figure 7: OAW-AP1362 Bottom View 060492-10 Rev. A *060492-10 Rev. A* 1.3.
PAGE 2
.2.1. Pole Mounting 2.2.2.2. Mounting Processes 2.2.1.1. Step-16. Draw four center marks on the wall where is planned to mount the outdoor AP. And then drill four Φ8×45 mm holes on the wall for expansion bolts. Materials Preparation Table 5 Item Description F Final assembly（F） Graphics Qty 1 Step-20 ◆ 2.3.3. Connecting the Grounding Wire D12 Hose clamp Step-16 2 Step-17. 2.2.1.2. Mounting Processes Step-14.
PAGE 3
6 BI_DB- 7 BI_DD+ 8 BI_DD- Bi-directional pair -B, PoE Positive Bi-directional pair +D, PoE Negative Bi-directional pair -D, PoE Negative 3.3. Power ⚫ Maximum (worst case) power consumption: <11.8W (802.3af PoE) 3.4. Environmental ⚫ Protective level of enclosure: IP67 ⚫ Operating Temperature: -40˚C to 65˚C Humidity: 5% to 95% non-condensing ⚫ Storage and transportation Temperature: -40˚C to 85˚C For additional specifications on this product, please refer to the Data Sheet.