Assembly Instruction

ManualsBrandsAlcott Hill ManualsCeiling LightsEngebretson 2 - Light 17'' Unique/Statement Bowl Flush Mount

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing

the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool

before removal. Do not subject glass parts to any shock while in operation or shattering may result.

1of5

Part

Description

Quantity

A Crossbar

Nipple

1pc.

2 pcs.

1pc.

Hex Nut

Package Contents

Lock Washer

1pc.

Ceiling Canopy

Shade

ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wire

strippers,electrical tape,safety glasses.

EstimatedAssemblyTime:20-30 minutes

BulbRecommended: (2) MediumBase 75WMaximum

Preparation:Identify andinspect allparts beforebeginning installation.Check package

contentlist anddiagrams belowto besure allparts arepresent. Ifany partsare missing

ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer

servicefor replacementparts.

Finial

Assembly Instruction

Summary of content (5 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (2) Medium Base 75W Maximum Estimated Assembly Time: 20-30 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
FINISH: VINTAGE BRONZE 2.4mm 13Ga GND 1 6” 3.5” 2 16” Dia. 17” Dia. (2) 75W Medium Base Bulbs (Not Supplied) NO. PART NUMBER NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" REPLACEMENT PART DESCRIPTION REQ.
PAGE 3
Assembly Instruction STEP 1 - Attach Crossbar to Outlet Box Figure 1 Outlet Box A. Secure the Crossbar (A) to the outlet box with outlet box screws (not supplied). Tighten until snug. Mounting Hole Crossbar Outlet Box Screw (not Supplied) STEP 2 - Attach Nipple to Crossbar Figure 2 A. Locate the Nipple (B) and thread one Hex Nut (D) onto it about half way. Slip a Lock Washer (C) onto it and thread one end of the Nipple (B) into the center hole of the Crossbar (A). B.
PAGE 4
Assembly Instruction STEP 6 - Make Wire Connections A. Use standard wire connectors to make all wire connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors. B. Connect White Supply Wire from the Outlet Box to White Wire from fixture. C. Connect Black (or Red) Supply Wire from the Outlet Box to Black Wire from fixture. D. Connect Ground Wire from the Outlet Box to Ground Wire from fixture. E.
PAGE 5
Assembly Instruction STEP 6 - Install Bulb A. This fixture uses standard bulb with a medium screw base . Maximum 75 watts. B. Insert bulb and screw snugly into place. Socket Bulb Figure 7 STEP 7 - Install Shade Spring A. Locate the Shade (G) wedge in the two Shade Holders without Spring. Pull the one Shade Holder with the Spring outside and position the Shade (G) onto the bottom of the Ceiling Canopy (E). The Shade Holder will engage the Shade (G) after release.