00 WATT CD STEREO SYSTEM BLUETOOTH® WITH MULTICOLOR BEAT-PULSING LED LIGHTS Model: CD6698BL PRODUCT GUIDE
Safety Precautions WARNING: SHOCK HAZARD-DO NOT OPEN AVERTISSEMENT: RISQUE DE CHOC ÉLECTRIQUE-NE PAS OUVRIR * SEE MARKING ON REAR OF PRODUCT * WARNING: • TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE. • TO AVOID ELECTRICAL SHOCK, DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. EN • THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUID, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
Safety Precautions • If the unit is brought directly from a cold to a warm location, or is placed in a very damp room, the moisture may condense on the lens inside the unit. Should this occur, the unit will not operate. In this case, remove the disc and leave the unit in a warm place for several hours until the moisture evaporates. • For the unit to operate at its best, it should not be subject to temperatures below 41°F (5°C) or above 95°F (35°C).
LOCATION OF CONTROLs 1. CD Door 2. / TUNE – button / TUNE + button PLAY/PAIR button STOP button OPEN / CLOSE button 3. DISPLAY 4. USB port (for charging only) 5. VOLUME control 6. Remote sensor 7. STANDBY/ON button / PRESET EQ button / MEM.UP button PROG/MEM button SOURCE button 8. Line in / Aux jack 1 2 3 6 7 4 8 5 EN EN REMOTE CONTROL 1 9 10 2 11 3 12 4 5 13 14 6 15 7 8 1. ON/STANDBY button 2. SOURCE button 3. / TUNE – button 4. STOP button 5. PLAY/PAUSE button 6. / PROG/MEM button 7.
SYSTEM CONNECTIONS SPEAKER CONNECTIONS Connect the speakers to the R terminal and the L terminal. NOTE : Connecting speakers other than the speakers supplied with the unit may damage the unit. CAUTIONS: • Ensure that the power supply in your house complies with that indicated on the identification sticker located on the back of your unit. (AC 120V ~ 60Hz). • If you are not going to use the unit for a long time, disconnect the AC power plug from the wall outlet. • This unit is designed for continuous use.
Playback via Bluetooth® enabled devices Initial device pairing and connection In order to pair and connect your Bluetooth® device for the first time: 1. Press the SOURCE button to Bluetooth® mode and “ ”icon is shown on the display. The “ ” icon flashes which means the unit is in Bluetooth® mode and ready to pair. 2. Turn on the Bluetooth® device you wish to pair and connect. 3. Press and hold the PAIR button on the remote control for 3 seconds.
RANDOM PLAYBACK All tracks on the disc can be played in random order (Using the remote control only). Random Playback Press the RANDOM button on the remote control until “ ” is shown on the display. All tracks will be played randomly. To cancel, press the RANDOM button on the remote control until “ ” disappears. PROGRAMMABLE CD PLAYBACK A program of up to 20 tracks can be set to play in a preset order. 1. In CD stop mode, press the /PROG/MEM button and the “MEM” & “ ” will blink on the display. 2.
TROUBLESHOOTING GUIDE Problems BLUETOOTH® Bluetooth® devices doesn’t pair with this unit. CD Disc in place but unit won’t play Disc skips RADIO Poor FM reception OTHERS System doesn’t turn on No sound Solutions • Make sure your Bluetooth® device is working properly. • Make sure the source is Bluetooth® mode. • Check your device’s manual for details on Bluetooth® pairing and linking. • Make sure the source is CD mode. • Make sure button is pressed. • Make sure disc label is facing up.
LIMITED WARRANTY VENTURER ELECTRONICS (“VENTURER”) makes the following limited warranty. This limited warranty extend to the original consumer purchaser and is limited to non-commercial use of the product. Ninety (90) Day Parts & Labor Warranty Venturer products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of ninety (90) days from the date of their original retail purchase.
Printed in China 811-669891W010 BWA17AA005_IB_r.